1. Introduction
The NEEWER QZ-C is a versatile 2.4G TTL wireless flash trigger designed for Canon R6, R5, and 6D Mark II cameras. It features an intuitive HD OLED touchscreen for smooth control, supporting multiple flash modes including TTL, Manual, and Strobe. With its 2.4G Q System, it can remotely trigger compatible NEEWER Q flashes, offering 1/8000s HSS sync and a 100m transmission range. The trigger is powered by a 1000mAh rechargeable lithium battery, providing 6-10 hours of runtime.

2. Package Contents
- 1 x NEEWER QZ-C Flash Trigger
- 1 x USB to Type-C Cable
- 1 x Storage Case

3. Setup
3.1 Mounting the Trigger
- Ensure your camera is turned off.
- Slide the NEEWER QZ-C flash trigger onto your camera's hot shoe until it clicks into place.
- Tighten the locking mechanism (if present) to secure the trigger.
3.2 Initial Charging
Before first use, fully charge the device using the provided USB-C cable. Connect the USB-C cable to the trigger's charging port and the other end to a suitable USB power source. Charging time is approximately 2.5 hours.

4. Operating Instructions
4.1 Power On/Off
Press and hold the power button to turn the device on or off.
4.2 Touchscreen Controls
The HD OLED touchscreen allows for intuitive control. Swipe or tap on the screen to navigate menus and adjust settings.
- Page Lock: To prevent accidental touches during shooting, pull down the screen to activate the page lock. Long press the flash trigger button for 2 seconds or tap the screen for 2 seconds to unlock.
- Adjustable Screen Brightness: Swipe down to access the settings UI and tap 'MENU' to open the menu. Slide to adjust the screen brightness for optimal visibility in any lighting environment.

4.3 Flash Modes
- TTL Auto Flash: Automatically adjusts flash output for correct exposure.
- Manual (M) Mode: Allows manual adjustment of flash output from 1/256 to 1/1.
- Strobe Mode: Fires a series of rapid flashes for creative effects.
- Exposure Compensation: Adjust flash exposure by ±3 EV in 1/3 EV increments.
- S1/S2 Mode: Optical slave modes for triggering off-camera flashes.
- Zoom Setting: Automatic or manual zooming from 20mm to 200mm.
4.4 TCM Conversion
With TCM conversion, you can effortlessly switch between the high efficiency of TTL mode and the precision of manual mode. Note: To enable the TCM function, please update your flash firmware to the latest version. This feature is only supported on Q6, Z2-C, Z2Pro-C, Z3-C and Z880-C flashes.

4.5 2.4G Q System
The built-in 2.4G Wireless Q System allows remote control of compatible NEEWER Q flashes (off-camera only). It supports 5 groups (A, B, C, D, E), 32 channels, and IDs from 01-99. The transmission range is up to 100m.

4.6 High Speed Sync (HSS)
Achieve shutter speeds up to 1/8000s for freezing fast action or using wide apertures in bright conditions.

5. Maintenance
5.1 Battery Charging
Charge the 1000mAh lithium battery using the USB Type-C port. A full charge takes approximately 2.5 hours. The device supports real-time battery display on the screen.
5.2 Firmware Update
Update firmware via the Type-C port for new features and improvements. Refer to the NEEWER official website for the latest firmware and update instructions.
6. Troubleshooting
- Device Unresponsive: If the device becomes unresponsive, press and hold the power button and test button simultaneously to force a shutdown.
- TTL/Strobe Modes Not Working: Ensure single contact mode is disabled in the settings for proper TTL and Strobe functionality.
- TCM Function Issues: If TCM is not working, verify that your flash firmware is updated to the latest version and that your flash model (Q6, Z2-C, Z2Pro-C, Z3-C, Z880-C) is supported.
- Connectivity Problems: Check that the flash trigger and receiver flashes are set to the same group, channel, and ID. Ensure they are within the 100m transmission range.
7. Specifications
| Feature | Description |
|---|---|
| Model | QZ-C |
| Weight | 60g (2.1oz) |
| Dimensions | 64 x 41 x 38mm (2.5" x 1.6" x 1.5") |
| Compatible Brand | Canon |
| Compatible Models | R6, R5, R3, R, M6, 850D, 800D/T7i, 760D/T6s, 750D/T6i, 650D, 600D, 7D Mark II, 7D, 6D Mark II, 6D, 5D Mark IV/III/II, 1D Mark III, 1DX, 550D, 500D, 450D, 90D, SL3/250D, T100/3000D 4000D (NOT compatible with RP R50 T7/1500D 2000D) |
| Battery | Built-in 3.7V, 1000mAh, 3.7Wh Lithium Battery |
| Charging Time | Approx. 2.5 hours |
| Battery Life | Approx. 6-10 hours |
| Flash Modes | TTL Auto Flash, Manual Flash, Strobe Flash |
| Sync Modes | Front Curtain Sync, Rear Curtain Sync, High-speed Sync (HSS up to 1/8000s) |
| Exposure Compensation | ±3EV in 1/3EV increments |
| Buzzer | Controllable via flash trigger |
| ZOOM Setting | Automatic, Manual (20-200mm) |
| TCM Conversion | Converts TTL shooting values to M output values |
| Firmware Update | USB C interface |
| Memory Function | Yes |
| Display | Touchscreen, screen brightness adjustable |
| Transmission Range | 0-100m |
| Channels | 32 |
| Wireless ID | OFF, 01-99 |
| Groups | A, B, C, D, E |

8. User Tips
- TTL and Strobe Mode Activation: For proper functionality of TTL and Strobe modes, ensure that the 'single contact mode' is disabled in the trigger's settings.
- TCM Function Compatibility: To utilize the TCM conversion feature, confirm that your NEEWER Q flash unit has the latest firmware installed and is one of the supported models (Q6, Z2-C, Z2Pro-C, Z3-C, Z880-C).
- Canon R7 Compatibility: While the Canon R7 is not officially listed as a compatible model, some users have reported success with similar Canon cameras. Always check for the latest firmware updates for the QZ-C trigger, as these may expand compatibility.
9. Warranty & Support
For detailed warranty information, technical support, or service inquiries, please refer to the official NEEWER website or contact their customer service department. Keep your purchase receipt as proof of purchase.