JIKONG 3.2inch V19 SOC Display LCD-12864-TTL

Contents

JIKONG 3.2-inch V19 SOC Display User Manual

Model: LCD-12864-TTL

1. Product Introduction

This module is a 3.2-inch graphical LCD display specifically designed for energy storage battery management systems (BMS). It features a 128x64 resolution dot-matrix blue screen LCD and has a built-in TTL communication interface. Users can view key parameters such as current battery voltage, current, and state of charge (SOC) via buttons, and also configure the protection board's CAN/RS485 protocol settings through the buttons.

Important Note: This 3.2-inch V19 Display is only compatible with JKBMS PB Series models: JK-PB1A16S10PV19, JK-PB1A16S15PV19, JK-PB2A16S15PV19, JK-PB2A16S20PV19, and JK-PB2A16S30PV19. It cannot be used with other BMS models.

JIKONG 3.2 inch V19 SOC Display compatibility with JKBMS PB Series models.
JIKONG 3.2 inch V19 SOC Display compatibility with JKBMS PB Series models.

2. Specifications

AttributeValue
Brand NameJIKONG
TypeLIFEPO4 Battery BMS Display
ModelLCD-12864-TTL
Display Size3.2 inch
Resolution128x64 dot-matrix
Display ColorBlue screen
Communication InterfaceTTL
Usage ScenarioPower BMS
Balance FunctionActive Balanced BMS
Charge and Discharge PortCommon Port BMS
Charging Current10A
FunctionShort Circuit Protection
OriginMainland China

2.1 Mechanical Dimensions

Mechanical dimensions and connector locations of the JIKONG 3.2 inch V19 Display.
Mechanical dimensions and connector locations (Switch Key Connector, Display Cable) of the JIKONG 3.2 inch V19 Display. Dimensions: 105mm (length) x 69.40mm (width).

3. Setup and Connection

3.1 Packing List

Ensure all components are present:

  • 1 x 3.2 Inch Display
  • 1 x Cable (50 cm)
Packing list showing 1x 3.2 Inch Display and 1x Cable.
Packing list showing the 3.2 Inch Display and its connecting cable.

3.2 Interface and Cables

The display module features two main interfaces:

  • P1 Activation Switch Interface (GH1.25-6P)
  • P2 User Interface (HY2.0-6P)
JIKONG 3.2 inch Screen Display (LCD-12864-TTL) with 50 cm display cable.
JIKONG 3.2 inch Screen Display (LCD-12864-TTL) with its 50 cm display cable.

3.3 Connection Diagram

Connect one end of the provided cable to the user interface (P2) of the display screen and the other end to the TTL communication interface of the protection board. There is no need to distinguish the direction of the cable for connection.

Connection diagram of the JIKONG 3.2 Inch Screen Display (LCD-12864-TTL) to a JIKONG V19 PB Serial BMS via UART Connector.
Connection diagram of the JIKONG 3.2 Inch Screen Display (LCD-12864-TTL) to a JIKONG V19 PB Serial BMS via UART Connector.

3.4 Interface Pin Definition

ConnectorPin No.Description
P1 Activation Switch Interface (GH1.25-6P)1VIN: Connect to 12V power supply
2RXD: Connect to protection board TX
3TXD: Connect to protection board RX
4GND: Ground connection
5K+: Connect to the positive terminal of the switch
6K-: Connect to the negative terminal of the switch
P2 User Interface (HY2.0-6P)1K-: Connect to the negative terminal of the switch
2K+: Connect to the positive terminal of the switch
3GND: Ground connection
4TXD: Connect to protection board RX
5RXD: Connect to protection board TX
6VIN: Connect to 12V power supply

4. Key Operation and Display Instructions

4.1 Button Functions

The display features four buttons for navigation and control:

  • K1: Power button / Menu button
  • K2: Confirm button
  • K3: Down / Up button
  • K4: Back button
Display interface showing menu options (GROUP, PACKS, SETTING, ABOUT) and button functions (Power/Menu, Confirm, Down/Up, Back).
Display interface showing menu options and button functions.

4.2 Initial Startup

After correctly connecting the display to the protection board, press the K1 power button to activate the protection board. To shut down the protection board, long press K1. The initial display interface after startup will show the main menu:

  • GROUP
  • PACKS
  • SETTING
  • ABOUT

4.3 Viewing Battery Group Information (GROUP)

From the main menu, use K3 to move the cursor to the “GROUP” option, then press K2 to display relevant information of the current battery group. This includes parameters like Voltage (Vtg), Current (Cur), State of Charge (SOC), and Capacity (CAP).

Display showing inverter protocol information (Vtg, Cur, SOC, CAP) and options to set up RS485 and CANBUS protocols.
Display showing detailed battery group information and protocol setup options.

4.4 Viewing Individual Cell Information (PACKS)

Press K4 to return to the previous menu. From the main menu, select the “PACKS” option using K3 and press K2 to display the voltage of each cell in the current battery pack. Only 4 cells are displayed per page; press K3 to switch to the next page to view more cells.

4.5 Protocol Settings (SETTING)

From the main menu, select “SETTING” using K3 and press K2 to enter the protocol settings page. Here, you can use K3 to choose between setting the CAN or RS485 protocol. Press K2 to confirm your selection. Continue using K3 for navigation and K2 for confirmation to complete the protocol configuration.

4.6 About Information (ABOUT)

From the main menu, select “ABOUT” using K3 and press K2 to enter the About page. This page displays the current software version information of the display module (e.g., Ver:1.10).

5. Maintenance

  • Keep the display clean and free from dust and moisture.
  • Avoid exposing the device to extreme temperatures or direct sunlight for prolonged periods.
  • Do not use harsh chemicals or abrasive cleaners on the screen or casing. Use a soft, dry cloth for cleaning.
  • Ensure all cable connections are secure to prevent intermittent operation.

6. Troubleshooting

6.1 Common Issues

  • Display not turning on:
    • Check if the display cable is securely connected to both the display (P2) and the BMS TTL communication interface.
    • Ensure the BMS is powered on and providing 12V to the display's VIN pin.
    • Press the K1 power button firmly.
  • Incorrect data displayed:
    • Verify that the display is compatible with your specific JKBMS PB Series model (refer to Product Introduction).
    • Check the communication cable for damage or loose connections.
    • Ensure the correct protocol (CAN/RS485) is configured in the 'SETTING' menu if applicable.
  • Buttons unresponsive:
    • Ensure the display is powered on.
    • Gently press the buttons to check for any physical obstruction.

7. User Tips

  • For optimal readability, install the display in a location with adequate lighting but away from direct glare.
  • When navigating menus, a short press on K3 moves the cursor, and a short press on K2 confirms the selection. K4 always acts as a 'Back' button.
  • Regularly check the 'ABOUT' section to note the software version, which can be helpful for support inquiries.

8. Warranty and Support

For warranty information and technical support, please refer to the official JIKONG Smart BMS Store or contact your point of purchase. Keep your purchase receipt as proof of purchase.

A user manual in PDF format is available for download: JIKONG 3.2-inch Lattice Screen Operation and Maintenance Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.