HXCONTROLLER HM Series MPPT Solar Charge Controller

Contents

HXCONTROLLER HM Series MPPT Solar Charge Controller

User Manual for 60A, 100A, and 120A Models with WiFi Monitor

1. Introduction

Thank you for choosing the HXCONTROLLER HM Series MPPT Solar Charge Controller. This manual provides essential information for the safe and efficient operation of your device. Please read it thoroughly before installation and use.

1.1 What is MPPT Technology?

Maximum Power Point Tracking (MPPT) is an advanced charging technology that adjusts the working status of electrical modules to enable the battery board to output more electricity. Due to the nonlinear characteristics of solar arrays, there exists a maximum energy output point (maximum power point) on their curve. Traditional controllers (switch charging technology and PWM charging technology) cannot maintain charging the battery at this point, and therefore cannot obtain the maximum energy of the battery panel. However, solar controllers with MPPT control technology can always track the maximum power point of the array to obtain the maximum energy to charge the battery.

1.2 Key Features

  • Advanced MPPT Charging Mode: High efficiency (≥98.1%) and PV utilization (≥99%). Built-in DSP controller.
  • Automatic Battery Voltage Detection: Supports 24V to 192V systems.
  • Multiple Battery Adaptation: Compatible with USER (Lithium, LiFePO4, Li(NiCoMn)O2), Vented, Flooded, Sealed, Gel, and NiCd batteries. User-programmable for absorption voltage, floating voltage, low voltage disconnect, and load timer.
  • HD Colorful Display: Provides clear visibility of solar panel voltage, battery voltage, charging current, daily/total cumulative power generation, equipment temperature, battery type, and other parameters.
  • Built-in WiFi Device & APP Monitoring: Allows remote monitoring of the controller's working status via a smartphone app (iOS and Android). Requires a 2.4GHz WiFi network within 5-10m of the router for optimal signal.
  • Max 480V Solar Panel Input: Supports high voltage solar panel configurations, allowing more panels in series.
  • Fan Heat Dissipation: Intelligent fan cooling activates at >45℃ and turns off at <40℃, ensuring efficient heat dissipation and extended product life (up to 5000 hours).
  • Comprehensive Protections: Includes self-recovery, reverse connect protection, over-current protection, short-circuit protection, open-circuit protection, and high-temperature protection.

2. Safety Guidelines

Please observe the following safety precautions during installation and operation to prevent injury and damage to the controller or other components.

  • Battery Handling: When installing batteries, be very careful. For open lead-acid batteries, wear protective goggles. If contact with battery acid occurs, rinse immediately with clean water.
  • Short Circuits: Avoid placing metal objects near the battery to prevent short circuits.
  • Ventilation: During battery charging, acidic gases may be generated. Ensure good ventilation around the environment. Batteries may produce combustible gases; keep away from sparks.
  • Environmental Conditions: Outdoor installation should avoid direct sunlight and rainwater infiltration.
  • Connections: Virtual connection points and corroded wires may cause significant heating and melting of insulation, potentially leading to fires. Ensure all connection heads are tightened and secure. Use zip ties to fix wires in mobile applications to prevent shaking.
  • High Voltage: When connecting the system, the output voltage of the component may exceed the safety voltage of the human body. Use insulated tools and ensure hands are dry.
  • Battery Terminals: The battery terminals on the controller can be connected to either the same battery or the same set of batteries.
  • Battery Manufacturer Guidelines: Always follow the safety recommendations of the battery manufacturer.
  • Wiring: System connection wires should be selected according to a current density not exceeding 4A/mm².
  • Grounding: Ground the ground terminal of the controller.

3. Setup and Installation

3.1 Installation Safety Distance

To ensure effective heat dissipation of the controller, maintain the following safety clearances:

  • Left/Right: 20 cm
  • Top/Bottom: 30 cm
Diagram showing recommended safety distances for controller installation: 20cm clearance on sides, 30cm clearance on top and bottom.
Figure 3.1: Recommended installation clearances for heat dissipation.

3.2 Line Connection Requirements

Follow the connection sequence carefully to avoid damage:

  1. First, connect the positive and negative terminals of the battery.
  2. Then, connect the positive and negative terminals of the DC load.
  3. Finally, connect the positive and negative terminals of the solar panel.
Wiring diagram for the MPPT solar charge controller showing connections for PV input, battery, load, and RS485 communication. The diagram illustrates connecting the battery first, then the load, and finally the solar panel.
Figure 3.2: Wiring diagram for the controller.

Note: When activating the machine for the first time, ensure the battery has sufficient voltage to prevent the controller from failing to power on due to low voltage.

4. Operating Instructions

4.1 Controller Appearance and Interface

Diagram of the MPPT solar charge controller's front panel, highlighting the LCD display, control buttons (ESC, UP, DOWN, SET), and indicator lights for PV, Charge, Load, and Alarm.
Figure 4.1: Controller appearance and interface.

The controller features a colorful LCD display and four buttons for navigation and settings:

  • ESC: Escape/Back
  • UP: Navigate Up / Increase Value
  • DOWN: Navigate Down / Decrease Value
  • SET: Confirm / Enter Setting

4.2 Key Operation and Display Information

The display provides real-time information about your solar system. Use the UP and DOWN buttons to browse different screens and the SET button to confirm selections.

Close-up of the controller's display showing various parameters like PV voltage, current, battery voltage, device temp, battery type, load mode, system volume, and status.
Figure 4.2: Detailed view of the colorful display.

The main display shows:

  • PV: Solar panel status and input voltage/current.
  • CHARGE: Battery charging status and voltage/current.
  • LOAD: Load status and output voltage/current.
  • ALARM: Indicates system warnings or faults.
  • Daily/Total: Daily and total cumulative power generation (KWH).
  • Device Temp: Internal temperature of the controller.
  • Bat Type: Configured battery type (e.g., Seal, Gel, User).
  • Load Mode: Current load operating mode (e.g., Keep On, Light).
  • System Vol: Configured system voltage (e.g., Auto).
  • Load Switch: Status of the load output (Turn On/Turn Off).
  • Status: Current operating status (e.g., System normal, Charging ready, Charge power tracking).

4.3 Quick Parameter Setting

Press and hold the SET button for 5 seconds to enter quick settings. Here you can adjust basic parameters:

Quick Settings
SettingValue/Option
Backlight modeKeep On
Load output TypeLight control/Manual
Load setting time17:30–08:30
Time settingYYYY-MM-DD HH:MM
Clean generationNO
LanguageEnglish

4.4 Advanced Settings

To enter advanced settings, press and hold the ESC key and the SET key for 5 seconds. You will be prompted to enter a password. The default password is 1111.

In advanced settings, you can customize battery parameters, including absorption voltage, floating voltage, and low voltage disconnect. This allows fine-tuning the controller's behavior to match your specific battery type and system requirements.

4.5 WiFi Monitoring (APP)

The controller has a built-in WiFi device for remote monitoring via a smartphone app. Both iOS and Android systems are supported.

Screenshots showing the steps to set up the WiFi monitoring app: Download 'Smart Life' app, Register Account, Input WiFi Password, View Historical Data, and Adjust User Settings.
Figure 4.3: WiFi APP setup and monitoring interface.

Setup Steps:

  1. Download: Search for "Smart Life" in your app store or scan the QR code in the user manual (PDF).
  2. Register Account: Use your phone or Apple ID to register.
  3. Input WiFi Password: Turn on WiFi, allow the app to obtain mobile phone permissions, and enter your WiFi password.
  4. Monitor: View historical data and adjust user settings.

WiFi Status Indicator:

WiFi Status Display
WiFi Module AbnormalityShow
WiFi not connectedWiFi icon flashes white slowly
Excellent WiFi signalWiFi icon 3 bars blue
Good WiFi signalWiFi icon 2 bars blue
Poor WiFi signalWiFi icon 1 bar blue

Important: Install the controller in a location with good WiFi signal. The controller should be 5-10m away from the router. Only 2.4GHz WiFi networks are supported.

5. Specifications

The following table details the specifications for the HXCONTROLLER HM Series MPPT Solar Charge Controllers:

Detailed parameter table for MPPT Solar Charge Controller HM Series, including models 60A, 100A, and 120A, showing maximum photovoltaic voltage, charging current, battery types, maximum input power of solar panel, charging voltage, charging method, DC output current, operating temperature, cooling method, altitude, product size, and gross weight.
Figure 5.1: HM Series MPPT Solar Charge Controller Parameter Table.
General Specifications
FeatureSpecification
Brand NameHXCONTROLLER
Model NumberMPPT 60A/100A/120A Solar Charge Controller (HM Series)
ApplicationVoltage Controller, Solar System Controller
Is Smart DeviceYes (Built-in WiFi)
Maximum Current60A, 100A, 120A (Adjustable)
Max Input Voltage (PV)480VDC (Solar Panel Open Circuit Voltage)
Battery Voltage24V-192V (Auto-recognition + adjustable)
Charging MethodPower tracking, fast charging, floating charging
Start ChargingPhotovoltaic voltage > battery voltage + 2V
DC Output Current40A
Operating Temperature-20°C to 65°C (Max 65 degree)
Cooling MethodAir Cooling, Fan
Altitude0-3000m
Product Size (60A)262x218x102mm
Product Size (100A/120A)329x268x102mm
Gross Weight (60A)2.8kg
Gross Weight (100A/120A)5kg
CertificationCE

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your MPPT solar charge controller.

  • Cleaning: Periodically clean the exterior of the controller to prevent dust buildup, especially around ventilation openings. Use a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.
  • Connections: Regularly check all wiring connections (solar panel, battery, load) to ensure they are tight and free from corrosion. Loose connections can lead to overheating and inefficient operation.
  • Ventilation: Ensure that the area around the controller remains clear of obstructions to allow for proper airflow and heat dissipation. Maintain the recommended safety distances.
  • Firmware Updates: Check the manufacturer's website or app for any available firmware updates to ensure your controller has the latest features and bug fixes.
  • Battery Health: Monitor your battery's health and voltage regularly. Ensure your battery type settings in the controller match your actual battery type for optimal charging.

7. Troubleshooting

If you encounter issues with your controller, refer to the following common problems and solutions:

  • Controller Not Powering On:
    - Check battery connections and ensure they are secure.
    - Verify that the battery voltage is sufficient to power the controller (especially during first activation).
  • No Charging from Solar Panels:
    - Check solar panel connections and polarity.
    - Ensure solar panel voltage is above the battery voltage + 2V to initiate charging.
    - Verify that there is sufficient sunlight.
    - Check for any alarms on the display indicating PV input issues.
  • Load Not Working:
    - Check load connections and ensure they are secure.
    - Verify the load mode settings (e.g., Keep On, Light control) and load switch status.
    - Check battery voltage; if it's too low, the controller may disconnect the load to protect the battery.
  • WiFi Connection Issues:
    - Ensure the controller is within 5-10m of a 2.4GHz WiFi router.
    - Check WiFi signal strength on the controller's display (refer to WiFi Status Indicator table).
    - Verify the WiFi password entered in the app is correct.
    - Restart the controller and your router.
  • Overheating:
    - Ensure adequate ventilation around the controller and that safety distances are maintained.
    - Check if the cooling fan is operating correctly when the device temperature rises above 45°C.
  • Alarm Indication:
    - Refer to the controller's display for specific alarm codes or messages. Consult the full user manual (PDF) for detailed explanations of alarm conditions.

For more detailed troubleshooting, please refer to the comprehensive user manual PDF: View User Manual (PDF)

8. User Tips

  • The MPPT functionality of this controller is highly effective, providing superior charging efficiency compared to older PWM controllers.
  • The colorful display is clear and easy to read, making it convenient to monitor system parameters.
  • Ensure your WiFi signal is strong and 2.4GHz for reliable app monitoring.
  • Properly secure all connections to maximize efficiency and prevent issues.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact HXCONTROLLER Official Store directly. Keep your purchase receipt as proof of purchase.

You can also refer to the detailed user manual (PDF) for additional support and information:

Download Full User Manual (PDF)

10. Product Video

Video demonstrating the controller's display and connections, showcasing its operation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.