JIKONG V19

Contents

JIKONG V19 Active Balance BMS User Manual

Model: V19 | Brand: JIKONG

1. Introduction

This manual provides comprehensive instructions for the JIKONG V19 Active Balance Battery Management System (BMS). The JIKONG V19 BMS is designed for large capacity series lithium battery packs, offering advanced features such as active balancing, voltage acquisition, and various protection mechanisms. It supports Li-ion, LiFePO4, and LTO battery types and is suitable for a wide range of applications.

2. Key Features

The JIKONG V19 BMS offers a robust set of features to ensure optimal battery performance and safety:

  • Active Balancing: Continuous balancing current of 0.4A-2A for enhanced battery consistency and extended lifespan.
  • Wide Battery Compatibility: Supports Li-ion, LiFePO4, and LTO battery types.
  • Cell Configuration: Compatible with 4S-8S battery strings.
  • Current Ratings: Available in various continuous charge/discharge current options (40A, 60A, 100A, 200A, 300A).
  • Communication Interfaces: Built-in Bluetooth, with optional support for HEAT, CANBUS, and RS485.
  • Display Options: Available with 2.3-inch, 3.2-inch, or 4.3-inch LCD displays.
  • Comprehensive Protection: Includes overcharge, over-discharge, overcurrent, short circuit, over-temperature, and low-temperature protection.
  • Smart Functions: Features intelligent sleep mode, alarm function, and ACC detection.
  • GPS Support: Optional GPS interface for battery location tracking.
  • Heating Function: Optional heating to maintain battery activity in low temperatures.

3. Application Scenarios

The JIKONG V19 Active Balance BMS is suitable for a wide range of applications, including:

Diagram showing various application scenarios for the JIKONG BMS, including E-bikes, Electric Tricycles, Low Speed Quads, Forklifts, Cleaning Cars, Tourist Cars, Industrial Drones, Scooters, RV Energy Storage, Lithium batteries, Power Banks, and Storage batteries.

Figure 3.1: Wide range of application scenarios for the JIKONG BMS.

  • E-bikes and Electric Tricycles
  • Low Speed Quads and Scooters
  • Forklifts and Cleaning Cars
  • Tourist Cars
  • Industrial Drones
  • RV Energy Storage
  • Power Banks and general Lithium battery applications
  • Storage battery systems

4. Product Overview (Section 1.1 from PDF)

The lithium battery intelligent protection board is a management system tailored for large capacity series lithium battery packs, with voltage acquisition, high current active balancing, overcharge over-temperature protection, coulomb meter, Bluetooth communication, GPS remote and other functions. It can be applied to lithium iron phosphate, ternary lithium battery types.

The protection board relies on energy transfer active balancing technology with independent intellectual property rights, which can achieve a maximum continuous 2A balance current. The high current active equalization technology can ensure the consistency of the battery to the greatest extent, improve the battery range, and delay the aging of the battery.

The protection board has a mobile APP supporting Android and iOS operating systems. The APP can be connected to the protection board through the Bluetooth of the mobile phone to check the working status of the battery, modify the working parameters of the protection board, control the charge and discharge switch, and so on. The protection board is small in size, simple in operation and full in function, and can be widely used in battery packs of small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage, base station backup power supply, solar power stations and other products.

5. Functional Characteristics (Section 1.2 from PDF)

The JIKONG V19 BMS includes the following functional characteristics:

List of functional characteristics with checkmarks, including LED Bluetooth status indicator, APP remote operation, battery capacity calculation, high precision voltage/current acquisition, information screen display, accurate time logging, RS485/CAN/ACC/Parallel/Alarm/Heating/GPS support, and various charge/discharge protections.

Figure 5.1: Functional characteristics of the JIKONG BMS.

  • LED Bluetooth status indicator
  • APP Bluetooth remote operation
  • Battery capacity calculation
  • High precision voltage acquisition (±3mV)
  • High precision current acquisition
  • Support information screen display
  • Accurate time logging
  • Support RS485 (Optional)
  • Support CAN (Optional)
  • Support ACC detection function (Optional)
  • Support parallel function (Optional)
  • Support alarm function (Optional)
  • Support heating function (Optional)
  • Support GPS communication
  • Charge overcurrent protection
  • Charge overvoltage protection
  • Charge over temperature protection
  • Low temperature protection during charge
  • Discharge overcurrent protection
  • Discharge undervoltage protection
  • Discharge over temperature protection
  • Short circuit protection

6. Structural Block Diagram (Section 1.3 from PDF)

The following diagram illustrates the internal structure and main components of the JIKONG Active Balancing Protection Board (JK-B2A8S-30P).

Exploded view of the JIKONG BMS showing Cooling aluminum alloy, JIKONG MCU, MOS, and Sampling cable interface.

Figure 6.1: Exploded view of the JIKONG BMS showing key internal components.

Key components include:

  • JIKONG MCU: Main control unit.
  • MOS: Power MOSFETs for switching and protection.
  • Cooling Aluminum Alloy: For heat dissipation.
  • Sampling Cable Interface: For connecting cell voltage sensing wires.
  • Temperature Interface: For NTC temperature sensors.
  • GPS Interface: For optional GPS module.
  • Display Interface: For connecting LCD display.
  • Balance with Acquisition Interface: For active balancing and cell voltage acquisition.

7. Product Selection Guide (Sections 2.1, 2.2, 2.3 from PDF)

This section provides guidance on selecting the appropriate JIKONG BMS model based on your battery configuration and desired features.

7.1. Product Function Configuration Table (JK-B2A8S-30P)

Serial NumberFunctionConfiguration
1Active equalizing current2A
2Bluetooth functionStandard option
3GPS interfaceStandard option
4NTC quantity1 built-in, 2 external, 4 external optional configuration
5CANOptional
6RS485Optional
7Display interfaceStandard option
8Heating functionOptional
9Alarm functionOptional
10Battery parallel functionOptional
11ACC detection functionOptional
12Charging overvoltage, overcurrent protectionStandard option
13Discharge undervoltage, overcurrent protectionStandard option
14Short circuit protectionStandard option

7.2. Product Adaptation Guide

Serial NumberProduct SpecificationBattery TypeNumber of Adaptive Battery Strings
1JK-B2A8S-30PTernary lithium battery3~8
Lithium iron battery3~8
Lithium titanate battery7~8

7.3. Function Selection Guide

Serial NumberBattery StringOptional FunctionProduct Model
13~8Standard optionJK-B2A8S-30P
2Standard + CAN communicationJK-B2A8S-30PC
3Standard + RS485 communicationJK-B2A8S-30PR
4Standard + heatingJK-B2A8S-30PH
5Standard + heating + CAN communicationJK-B2A8S-30PHC
6Standard + heating + RS485 communicationJK-B2A8S-30PHR
7Standard + heating + CAN communication + RS485 communicationJK-B2A8S-30PHCR

8. Function Introduction and Usage Instructions (Section 3 from PDF)

8.1. Active Equalization (Section 3.1 from PDF)

Diagram illustrating active balancing, showing energy transfer from higher voltage cells to lower voltage cells to achieve voltage balance with minimal energy loss.

Figure 8.1: Active Balancing (Lossless Balancing) principle.

The protection board adopts active equalization technology. The principle of equalization is to transfer the energy of the high-voltage cell to the low-voltage cell, achieving energy transfer through the protection board. Before using the balancing function, users need to set the basic parameters of the battery and download the JIKONG BMS-APP. After downloading, set the battery type on the parameter setting page of the APP. For default parameters, refer to Section 9. After setting the battery type, set basic battery parameters in common settings, including the number of cells, battery capacity, trigger equalization differential pressure (the default value can be retained), voltage calibration, and current calibration.

Users can set the balance trigger pressure difference (mV) in the parameter setting of the APP. When the balance is turned on, it will be activated automatically if the pressure difference of any two strings of batteries in the battery pack is greater than the set value, and it will be turned off when the pressure difference is less than the set value. The default balance current is 2A. Users can adjust the balance current according to their own battery capacity. It is recommended that the balance current not exceed 0.2C of the battery capacity (C). If the balancing function is not needed, it can be set to off in the BMS control page of the APP.

8.2. GPS and Display Interface (Section 3.2 from PDF)

The protection board reserves a GPS port, enabling users to select a GPS device to meet battery location requirements. Additionally, a display interface is reserved, supporting JIKONG displays for convenient battery information viewing. Users can select these options based on their actual needs.

Icons representing various rich interfaces: CAN, RS485, BT (Bluetooth), NTC (Temperature), Soft Switch, SOC Indicator, Key Switch, Active Equalizer.

Figure 8.2: Rich interfaces available on the JIKONG BMS.

8.3. Heating Function (Section 3.3 from PDF)

The protection board supports an optional heating function. This uses a resistance heater or heating film to warm the battery at low temperatures, preventing charging and discharging issues due to reduced battery activity. The designed heating current is 20A. Users can control this function via the BMS control page in the APP based on ambient temperature. It is recommended to install a temperature control switch (45°C to 65°C normally closed type) in series with the heating circuit as a secondary protection to prevent thermal runaway.8.4. Alarm Function (Section 3.4 from PDF)

The protection board supports an optional alarm function. When the BMS detects safety risks such as overtemperature, overcharge, or overdischarge of the battery, an external alarm will be triggered.8.5. Battery Parallel Function (Section 3.5 from PDF)

The protection board supports an optional parallel function for battery packs, meeting the demand for energy storage systems. This function requires synchronous use with parallel modules, and the "disable charging current limiting" function must be turned off in the APP.

8.6. ACC Detection Function (Section 3.6 from PDF)

The protection board supports an optional ACC detection function, which can enable discharge. There are two ways to achieve this: apply voltage between ACC+ and ACC- (20V-100V), or directly short-circuit ACC+ and ACC-. Additionally, a charger detection function is reserved via C_detect+ and C_detect- interfaces for enabling charging.8.7. Charge Overvoltage Protection and Recovery (Section 3.7 from PDF)

The protection board is equipped with standard charge overvoltage protection. Users can set single overcharge protection voltage and recovery voltage in the APP. If any cell voltage exceeds the set protection voltage, the BMS will stop charging. Charging resumes when all cell voltages drop below the recovery voltage.8.8. Discharge Undervoltage Protection and Recovery (Section 3.8 from PDF)

Standard discharge undervoltage protection is included. Users can set undervoltage protection voltage, recovery voltage, and automatic shutdown voltage in the APP. If any cell voltage falls below the protection voltage during discharge, the BMS will stop discharging. Discharge resumes when all cell voltages rise above the recovery voltage. If any cell voltage falls below the automatic shutdown voltage, the BMS will automatically shut down.8.9. Charge Overcurrent Protection and Recovery (Section 3.9 from PDF)

Standard charge overcurrent protection is provided. Users can set continuous charging current, overcurrent delay, and recovery time in the APP. If the charging current exceeds the set limit for the specified delay, charging will stop. Charging resumes after the recovery time.8.10. Discharge Overcurrent Protection and Recovery (Section 3.10 from PDF)

Standard discharge overcurrent protection is provided. Users can set continuous discharge current, overcurrent delay, and recovery time in the APP. If the discharge current exceeds the set limit for the specified delay, discharging will stop. Discharging resumes after the recovery time. Note: The maximum continuous discharge current cannot exceed the design value of 300A.

8.11. Overtemperature Protection and Recovery (Section 3.11 from PDF)

Standard charge and discharge overtemperature protection is included. Users can set protection and recovery temperatures in the APP. If the temperature exceeds the set limit, charging or discharging will stop. Operation resumes when the temperature returns to a safe level.8.12. Low Temperature Protection and Recovery (Section 3.12 from PDF)

Standard charge low temperature protection is included. Users can set protection and recovery temperatures in the APP. If the temperature falls below the set limit, charging will stop. Charging resumes when the temperature rises above the recovery level. In extremely cold areas, using the optional heating function is recommended.8.13. Short Circuit Protection and Recovery (Section 3.13 from PDF)

Standard short circuit protection is included. Users can set short circuit protection delay (µs) and recovery time (S) in the APP. If a short circuit occurs during initial charging or connecting a load, the delay can be adjusted to prevent false triggers due to peak currents. The BMS will resume operation after the recovery time.8.14. Emergency Switch (Section 3.14 from PDF)

The BMS includes a standard emergency switch function. If issues like over-temperature, over-discharge, over-charge, or cell drop occur, activating the emergency switch in the APP will enable charge and discharge for 30 minutes, providing emergency use time. The protection board will continue to operate until the 30-minute cycle ends, even if cell voltage reaches automatic shutdown levels.8.15. Intelligent Sleep (Section 3.15 from PDF)

The BMS features a standard intelligent sleep function. Users can enable or disable this in the APP. This function closes the protection board when it's in standby (charging and discharging current less than 1A for 26 consecutive hours) to reduce energy consumption. It can be reactivated by pressing a button or connecting a charger.8.16. Communication Function (Section 3.16 from PDF)

The protection board supports optional CAN and RS485 functions. Users can select these based on their needs and set the address and communication protocol in the APP. Refer to the JIKONG Protection Board communication protocol document for specific details.

9. Specifications (Section 4 from PDF)

This section details the main parameters and default settings for the JIKONG V19 BMS.

9.1. Basic Parameters (Section 4.1 from PDF)

Serial NumberProjectArgumentUnit
1Supply voltage7.5-36V
2Operating power consumption<1400mW
3Operating temperature-30-70°C
4Maximum number of collection strings8String
5Maximum balancing current2A
6Maximum charging current300A
7Maximum discharge current300A
8Maximum instantaneous current600A
9Maximum internal loop resistance0.25mΩ
10Protective plate size182.75*127.26*15.6mm
11Finished weight541g

9.2. Default Parameters (Section 4.2 from PDF)

NUMParameterLi-ion DefaultLiFePO4 DefaultLTO DefaultUnit
1Balancing initial voltage332V
2Maximum balancing current222A
3Unit overcharge voltage4.23.62.7V
4Single overcharge protection recovery4.183.552.65V
5Monomer undervoltage protection2.822.61.8V
6Single undervoltage protection recovery2.852.651.85V
7Automatic shutdown voltage2.82.51.7V
8SOC-0% voltage2.92.61.85V
9SOC-100% voltage4.183.52.65V
10Trigger balancing differential pressure0.010.010.01V
11Charging overcurrent protection delay303030S
12Charge overcurrent protection release time606060S
13Discharge overcurrent protection delay300300300S
14Discharge overcurrent protection release time606060S
15Short-circuit protection delay555µS
16Short circuit protection release time303030S
17Charging overtemperature protection temperature707070°C
18Charge overtemperature restore temperature606060°C
19Discharge overtemperature protection temperature707070°C
20Discharge overtemperature recovery temperature606060°C
21Charging low temperature protection temperature-20-20-20°C
22Charge low temperature to restore temperature-10-10-10°C
23MOS Overtemperature protection temperature100100100°C
24MOS Overtemperature protection recovery temperature808080°C
25Device address000/

10. Interface Definition (Sections 5.1, 5.2 from PDF)

This section describes the physical appearance, connectors, and LED definitions of the JIKONG V19 BMS.

10.1. Product Appearance (Section 5.1 from PDF)

The JIKONG V19 BMS is designed with a compact and robust form factor. The overall dimensions for the JK-B2A8S-30P series protection board are 182.75mm × 127.26mm × 15.6mm.

10.2. Product Connector and LED Definition (Section 5.2 from PDF)

The BMS features several connectors for various functions. Below is a table detailing the interface definitions for the JK-B2A8S-30P model.

CouplerConnector TypeInterface NamePin NumberPin NameDefinition
P1XH-10AW-2.54Balance with Acquisition interface1B-Total negative battery
2B1The first battery positives
3B2The second battery positive
4B3The third battery positive
5B4The fourth battery positive
6B5The fifth battery positive
7B6The sixth battery positive
8B7The seventh battery positive
9B8The eighth battery positive
10B+Protection board power supply, connected to the battery
P2A1254WF-2A (Optional)Alarm interface1GNDAlarm power negative
2VCCAlarm power positive
P3A1254WF-4A (Optional)Communication interface1CAN LCAN signal negative terminal
2CAN HCAN signal positive terminal
3RS485 ARS485 signal positive terminal
4RS485 BNegative terminal of RS485 signal
P41.25T-4PWTGPS interface1GNDPower/signal ground
2RXUART RX, 3.3V
3TXUART TX, 3.3V
4VGPSPower output, the voltage is close to B+
P5HY2.0-4PTemperature interface (4 external optional)1T5AFifth temperature sensor pin A
2T5BFifth temperature sensor pin B
3T4AFourth temperature sensor pin A
4T4BFourth temperature sensor pin B
P6HY2.0-4PTemperature interface1T2ASecond temperature sensor pin A
2T2BSecond temperature sensor pin B
3T1AFirst temperature sensor pin A
4T1BFirst temperature sensor pin B
P7A1254WF-5A (Optional)ACC interface1ACC+ACC Positive
2ACC-ACC Negative
3NCEmpty
4C_Detect+The charger output 12V positive
5C_Detect-The charger output 12V negative
P8A1254WF-6ADisplay interface1VCCDisplay power output
2AThe display RS485 signal is positive
3BDisplay RS485 signal negative
4GNDNegative terminal
5K+Activation signal positive
P9A1254WF-3A (Optional)Parallel interface1P-statusParallel module status signal
2P-ENParallel module enable signal, output low level Turn on parallel module
3GNDSignal ground
Heating wire16AWG-Orange-15CM (Optional)1HT-Heater element negative electrode
D1Bluetooth connection indicatorWhen the Bluetooth is connected to the protection board, the indicator is steady on, and when the connection is disconnected, the indicator is blinking.
P-Connect to external load or negative terminal of charger, equipped with M6 screws.
B-Connect to the negative battery terminal, equipped with M6 screws.

11. Dimensions (Section 5.3 from PDF)

The dimensions of the JIKONG V19 BMS (JK-B2A8S-30P series protection board) are 182.75mm × 127.26mm × 15.6mm. The following diagram provides a visual representation of these dimensions.

Diagram showing the dimensions of the JIKONG BMS (JK-B2A8S-30P) with measurements in millimeters.

Figure 11.1: Dimensions of the JK-B2A8S-30P BMS.

Additionally, various LCD display options are available with different sizes and cable lengths:

Diagram showing 2.3 inch, 3.2 inch, and 4.3 inch LCD displays with their respective dimensions and cable lengths.

Figure 11.2: LCD display options and their dimensions.

  • 2.3 inch LCD: Cable C long 280mm, Cable B long 300mm, Cable C long 3000mm.
  • 3.2 inch LCD: Cable long 400mm. Dimensions: 100.5mm x 61.5mm.
  • 4.3 inch LCD: Switch Cable long 120mm. Dimensions: 140mm x 98mm.

12. Installation Method (Section 5.4 from PDF)

The JIKONG V19 BMS (JK-B2A8S-30P series protection board) is suitable for 3-8 series lithium battery packs. The wiring method varies depending on the number of cells in the battery pack. The general wiring diagram is shown below.

Wiring diagram for the JIKONG BMS (JK-B2A8S-30P) showing connections for load, charger, heating wire, temperature probe, and battery terminals.

Figure 12.1: JK-B2A8S-30P Wiring Diagram.

General Wiring Steps:

  1. Connect Balance Wires: Connect the balance wires from the battery cells to the P1 (Balance with Acquisition interface) connector on the BMS. Ensure correct polarity and sequence (B-, B1, B2... B+).
  2. Connect Main Power: Connect the main negative terminal of the battery pack to the B- terminal on the BMS. Connect the main positive terminal of the battery pack to the B+ terminal on the BMS.
  3. Connect Load and Charger: Connect the load and charger to the P- terminal (Load/Charger Negative) and B+ terminal (Load/Charger Positive) respectively.
  4. Optional Connections:
    • NTC Temperature Sensor: Connect NTC sensors to the P5/P6 temperature interfaces.
    • Heating Wire: If using the optional heating function, connect the heating wire to the HT- terminal.
    • GPS Module: Connect the GPS module to the P4 GPS interface.
    • Display Screen: Connect the LCD display to the P8 Display interface.
    • Communication Modules (CAN/RS485): Connect optional CAN or RS485 modules to the P3 Communication interface.
    • Parallel Module: If using the parallel function, connect the parallel module to the P9 Parallel interface.
    • ACC Detection: Connect ACC wires to the P7 ACC interface if using this function.

13. APP Operation Instructions (Section 6 from PDF)

The JIKONG V19 BMS can be managed and monitored via a mobile application.

13.1. APP Installation (Section 6.1 from PDF)

The mobile APP matching the product can be obtained by scanning the QR code below. An Android version 7 or higher is required for the Android APP.

QR code for JIKONG Mobile APP link.

Figure 13.1: QR code for JIKONG Mobile APP.

13.2. Device Activation (Section 6.2 from PDF)

Before powering on the protection board, ensure that the balance cable is properly connected and that P- and B- are correctly wired. Verify that the protection board is securely fixed to the battery cells. Failure to do so may lead to abnormal operation or damage.

The protection board does not have a power-on control switch. It is designed for charging activation mode (charger voltage 2V higher than battery voltage). After battery assembly, connect the charger to activate the protection board.

In addition to charging activation, the protection board also supports key activation and display activation. Users with a display screen and button can activate the device by inserting the cable into the display interface and pressing the button.

13.3. Parameter Setting (Section 6.3 from PDF)

Detailed instructions for setting protection board parameters are available in the "Instructions for Setting Protection Board Parameters" document. This document covers settings for voltage, current, temperature, and other operational parameters.

JIKONG BMS Communication showing mobile app interfaces and control options.

Figure 13.2: JIKONG BMS Mobile App Interface.

14. Troubleshooting

This section provides general guidance for common issues you might encounter with your JIKONG V19 BMS.

Common Issues and Solutions:

  • BMS Not Activating: Ensure all balance wires and main power connections (P- and B-) are correct and secure. Activate the BMS by connecting a charger (voltage 2V higher than battery) or by pressing the button on the optional display.
  • Balancing Not Occurring: Check the APP settings for active equalization. Ensure the balance trigger pressure difference is set correctly and the function is enabled. Verify that the battery type and cell count are accurately configured in the APP.
  • Overcurrent/Overvoltage/Overtemperature Protection Triggered: The BMS is functioning as designed to protect your battery. Check the battery cells for abnormalities, reduce the load/charge current, or allow the battery to cool down. Review APP settings for protection thresholds.
  • Short Circuit Protection Triggered: Disconnect the load/charger and inspect all wiring for actual short circuits. If no physical short is found, adjust the short circuit protection delay in the APP to accommodate high inrush currents from certain loads/chargers.
  • Communication Issues (Bluetooth/RS485/CAN): Ensure the respective communication modules are correctly connected and enabled in the APP. Check for proper wiring for RS485/CAN. For Bluetooth, ensure your mobile device's Bluetooth is on and paired with the BMS.
  • Inaccurate Readings (Voltage/Current/Temperature): Verify that all sensing wires (balance wires, NTC sensors) are correctly connected and not damaged. Perform calibration in the APP if available.
  • Heating Function Not Working: Ensure the optional heating module is connected correctly and the function is enabled in the APP. Check the temperature settings for low-temperature protection and heating activation.

If you encounter persistent issues, refer to the detailed parameter setting instructions in the full PDF manual or contact JIKONG technical support.

15. Warranty and Support

Service Commitment: The warranty covers goods within three years from the date of receipt, providing global warranty services for quality issues not caused by human factors (including functional failures, component defects, etc.). Service form: Support free repair or replacement (depending on the product's repairability evaluation results).

After-Sales Process:

  1. Customer Application: Submit applications through official after-sales channels (email/online customer service), providing order numbers, fault descriptions, and evidence (photos/videos).
  2. Return of Goods: The customer pays for the international logistics cost of sending the product back to China and provides the waybill number for tracking purposes.
  3. Packaging Requirements: Ensure that product accessories are complete and packaging is intact to avoid transportation damage.
  4. Detection and Processing: After receiving the product, the quality department will complete the inspection and inform the repair/replacement plan within 5-7 working days. Responsibility definition: Non-human damage: Free repair/replacement, and the seller bears the return international logistics costs.

For further support, please refer to the official JIKONG BMS Energy Store contact information.

16. Additional Resources

For the complete and detailed user manual, including advanced parameter settings and specific wiring diagrams, please refer to the official PDF document:

View User Manual (PDF)

© 2025 JIKONG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.