1. Introduction
This manual provides detailed instructions for the safe and efficient operation of your HZTZ Thermal Label Printer. Please read this guide thoroughly before use to ensure proper setup, functionality, and longevity of your device. This printer is designed for high-speed, no-ink label printing, ideal for small businesses, shipping, and various labeling needs.
1.1 Safety Precautions
Warning:
- It is strongly recommended to use the adapter provided by our company. Connecting an improper adapter may cause fire, explosion, or damage to the printer.
- When the printer is working or just after printing, do not open the top cover of the machine, and do not touch the print head or printer body with your hands. Overheating may cause burns.
General Precautions:
- Do not use or store the printer in places with high temperature, high humidity, or serious pollution.
- Connect the printer's power adapter to a properly grounded socket. Avoid using the same socket as a large motor or other device that can cause power voltage fluctuations.
- Avoid water or conductive substances (such as metal) entering the inside of the printer. Once this happens, turn off the power immediately.
- The printer must not print without paper, otherwise the printing roller and thermal print head will be seriously damaged.
- Users are not allowed to disassemble the printer for maintenance or modification without authorization.
- In order to ensure printing quality and product life, it is recommended to use equivalent quality thermal paper.
- Please keep this user manual properly for future reference.
2. Product Overview
Familiarize yourself with the physical components and dimensions of your thermal label printer.
2.1 Product Dimensions

2.2 Internal Components

2.3 Rear Ports and Controls

3. Setup
3.1 Paper Roll Installation
Follow these steps to correctly load thermal paper into your printer:
- Open the printer cover.
- Place the thermal paper roll as shown in the figure, with the paper side up, into the paper loading position. The maximum diameter for a roll is 100mm.
- Pull out a short length of paper to the outside of the box.
- Close the top cover.

Note: The printer supports both roll paper and stacked paper loading methods. Ensure the paper side is up for roll paper.
3.2 Software & Drivers
Printer drivers and tools can be downloaded from: www.cnfujun.com/d/66
The website provides resources for iOS, Android, Mac, and Windows users, including app downloads, print PDF videos, print label videos, and driver installation guides.
3.2.1 USB Connection for Mac OS
Note: Bluetooth connection is not supported on Mac systems for driver installation.
Before installing the driver, confirm the printer is turned on and connected to your computer via USB cable.
- Mac Driver Installation:
- Our package contains a USB flash drive with an installation package. Locate and double-click the file (e.g., "Labelprinter2.3.3.dmg").
- Double-click the installer package (e.g., "Label Printer_sign2.3.3.pkg").
- Click "Continue" through the installation prompts.
- Enter your computer's local password and click "Install Software".
- Click "Install" to proceed.
- Once installation is successful, click "Close".
- Add Printer to Your MacBook:
- Click the Apple icon in the upper left corner of your screen, then click "System Settings...".
- Navigate to "Printers & Scanners".
- Click "Add Printer, Scanner, or Fax..." to add the printer driver.
- For MAC (M1 system), click "+" to add a new printer.
- Select "LABEL-9X00" in the box to automatically identify and add it.
- Click "Add" to complete the addition.
3.2.2 Driver Installation for Windows OS
Find the "LabelDriver.exe" file, double-click to open it.
- User Account Control: If prompted, allow the app to make changes to your device.
- Install Printer Driver: Select "Installing the Printer Driver" and click "Next".
- Connection Check: Click "Next". Ensure the printer is powered on and the USB cable is connected to the computer.
- Specifying Ports:
3.2.2.1 USB Port Connection
- Select the USB port (e.g., SBOOL VID 0416 PID 5011) and click "Next".
- Default selected model, click "Next".
- Default generated printer name, click "Next".
- Prompt to prepare to install the driver, click "Next".
- If "Windows Security" appears, click "Install". The printer will automatically print a test page. Click "Close".
3.2.2.2 Bluetooth Port Connection
- Select the "Bluetooth" port and click "Next". Ensure your computer's Bluetooth is turned on.
- The computer will search for nearby Bluetooth devices. Select the printer with the default Bluetooth name "Bluetooth Printer" to connect. The printer's self-test page contains its Bluetooth name and address. The software default Bluetooth pairing code is "1234". Click "Next".
- Default selected model, click "Next".
- Default generated printer name, click "Next".
- Prompt to prepare to install the driver, click "Next".
- If "Windows Security" appears, click "Install". The printer will automatically print a test page. Click "Close".
3.2.2.3 Network or WIFI Port Connection
- Select the "Network or WIFI" port and click "Next".
- Click "Next".
- Default selected Port (from the self-test page, e.g., IP address 192.168.1.100), click "Next".
- Default generated printer name, click "Next".
- Prompt to prepare to install the driver, click "Next".
- If "Windows Security" appears, click "Install". The printer will automatically print a test page. Click "Close".
4. Operating Instructions
4.1 Printing on Mac
- Open the PDF file you wish to print.
- Click "File" then "Print...".
- Click "Other" to select the correct printing size.
- Select the desired label size, for example, "100mmX150mm" or "4.00x6.00".
- After selecting the size, click "Default Settings" then "Save Current Settings as Preset...".
- Enter a name for your preset (e.g., "Label Print Preset") and click "OK".
- Finally, click "Print" in the lower right corner of the print dialog.
4.2 Printing via Bluetooth/USB (General)
The printer supports both Bluetooth and USB connections for printing from various devices.

Ensure your device (iOS, Android, Windows, Mac OS, iPad) is connected to the printer via the appropriate method (Bluetooth or USB cable) and the necessary drivers/apps are installed as described in Section 3.2.
Video 4.1: Demonstration of the HZTZ Thermal Label Printer in action, printing various labels.
5. Maintenance
5.1 How to Clean the Print Head
The print head should be cleaned when:
- The printing is not clear.
- A vertical column of the printed page is not clear.
- Paper feeding noise is loud.
- There is too much carbon deposit on the print head.
Follow these steps for print head cleaning:
- Turn off the power of the printer, open the upper cover, and remove any paper.
- If you have just finished printing, wait for the print head to cool down completely.
- Use a soft cotton cloth dipped in absolute ethanol (should be wrung out) to wipe away dust and stains on the surface of the thermal sensor of the print head.
- Wait for the absolute ethanol to evaporate completely, then close the upper cover and try printing again.
Notice:
- Make sure the power is turned off during routine maintenance of the printer.
- Do not touch the surface of the print head with your hands or metal objects, and do not use tweezers and other tools to scratch the surface of the print head, printing roller, and sensor.
- Organic solvents such as gasoline and acetone must not be used.
6. Troubleshooting
6.1 Label Calibration and Exception Handling Methods
6.1.1 Label Calibration Method
If the paper is skipping or continuous printing occurs without stopping, the printer needs calibration:
- Put the paper into the printer and power on the printer.
- When the power light is on, press and hold the "FEED" button for 5-6 seconds until the LED light flashes and the buzzer beeps.
- Release the "FEED" button.
- Restart the printer and perform a test print.
Note: Calibration values may vary with different paper specifications. Perform calibration as needed.
6.1.2 Exception Handling After Calibration
(1) With paper, but the printer reports an error:
- Remove the paper and power off the printer.
- Power on the printer. Once the red light flashes, immediately long-press the "FEED" button.
- Release the button when the red light flashes again and the buzzer beeps.
- Wait 2 seconds, then restart the printer and test it again.
(2) Without paper, but the printer does not report an error:
- Remove the paper.
- Power on the printer and press and hold the "FEED" button for 5-6 seconds until the red light flashes and the buzzer beeps twice.
- Release the button.
- Restart the printer and perform a test print.
7. Specifications
| Feature | Detail |
|---|---|
| Brand Name | HZTZ |
| Type | Thermal Printer |
| Use | Thermal Printer |
| Print Speed | 20ppm |
| Max Paper Size | 110mm |
| Interface Type | Bluetooth |
| Signal Connection Type | Bluetooth |
| Supports Network Printing | Wired/Wireless |
| Paper Feed Mode | Friction Feed |
| Double-sided Printing | No |
| Battery Included | No |
| High-concerned chemical | None |
| Origin | Mainland China |
| Product Weight | 0.858 kg |
| Package Length | 20 cm |
| Package Width | 14 cm |
| Package Height | 10 cm |
8. User Tips
- Power Supply: The printer typically comes with its own power adapter. Ensure you use the provided adapter for optimal performance and safety.
- Connectivity: For Mac users, remember that Bluetooth is primarily for printing, not for initial driver installation. Use a USB cable for driver setup on Mac.
- Label Types: This thermal printer is versatile and can handle various label types, including shipping labels, product labels, and custom designs.
9. Warranty and Support
For warranty information, technical support, or further assistance, please refer to the official product page or contact the seller directly. A comprehensive user manual in PDF format is also available for download from the official product website: User Manual (PDF).
10. FCC Compliance
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Use only the supplied antenna.