JIKONG LCD-3.2D-STTL

Contents

JIKONG JKBMS 3.2 Inch SOC Power Display User Manual

Model: LCD-3.2D-STTL

1. Product Introduction

This module is a 3.2-inch graphical LCD display specifically designed for energy storage battery management systems (BMS). It features a 128x64 resolution dot-matrix blue screen LCD and has a built-in TTL communication interface. Users can view key parameters such as current battery voltage, current, and state of charge (SOC) via buttons, and also configure the protection board's CAN/RS485 protocol settings through the buttons.

JIKONG 3.2 Inch SOC Power Display
Figure 1: JIKONG 3.2 Inch SOC Power Display (LCD-3.2D-STTL)
Display compatibility with JIKONG PB series BMS
Figure 2: The 3.2 inch display is compatible with JIKONG PB Series BMS models including JK-PB1A16S10P V19, JK-PB1A16S15P V19, JK-PB2A16S15P V19, JK-PB2A16S20P V19, and JK-PB2A16S30P V19.

2. Specifications

2.1 General Specifications

  • Brand Name: JIKONG
  • Type: LIFEPO4 Battery BMS
  • Handware or Smart: SMART BMS
  • Balance Function: Active Balanced BMS
  • Charge and Discharge Port: Common Port BMS
  • Charging Current: 10A
  • Function: Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection
  • Usage Scenario: Power BMS, Energy Storage BMS, 3C Digital BMS
  • Certification: CE
  • High-concerned chemical: None
  • Origin: Mainland China

2.2 Physical Dimensions

Dimensions of the JIKONG 3.2 inch display
Figure 3: Dimensions of the display module. Length: 105mm, Width: 69.40mm, Height: 58.01mm. The screen itself measures 98.52mm x 56.40mm.
MeasurementValue
Overall Length105mm
Overall Width69.40mm
Overall Height58.01mm
Screen Length98.52mm
Screen Width56.40mm

3. Package Contents

  • 3.2 Inch Display x 1
  • Cable x 1
Packing list showing the 3.2 inch display and connecting cable
Figure 4: The package includes one 3.2 Inch Display and one connecting cable.
3.2 inch screen display with 50 cm display cable
Figure 5: The 3.2 inch screen display (LCD-12864-TTL) comes with a 50 cm display cable.

4. Setup and Installation

4.1 Interfaces and Cables

The display module features several connectors for power, communication, and switch activation. Refer to the table below for detailed interface definitions.

Display interface and buttons
Figure 6: Overview of the display module showing connectors and buttons.
ConnectorPinExplanation
P1 (Activation Switch Interface GH1.25-6P)1Connect to 12V power supply (VIN)
2Connect to protection board TX (RXD)
3Connect to protection board RX (TX)
4GND (Ground connection)
5Connect to the positive terminal of the switch (K+)
6Connect to the negative terminal of the switch (K-)
P2 (User Interface HY2.0-6P)1Connect to the negative terminal of the switch (K-)
2Connect to the positive terminal of the switch (K+)
3GND (Ground connection)
4Connect to protection board RX (TXD)
5Connect to protection board TX (RXD)
6Connect to 12V power supply (VIN)

4.2 Wiring Diagram

Simply connect one end of the wiring to the user interface (P2) of the display screen and the other end to the TTL communication interface of the protection board. There is no need to distinguish the direction of the wires for this connection.

Wiring diagram showing the 3.2 inch screen display connected to a JIKONG V19 PB Serial BMS via UART connector
Figure 7: Connection of the JIKONG 3.2 Inch Screen Display (LCD-12864-TTL) to a JIKONG V19 PB Serial BMS via the UART Connector.

5. Operation

5.1 Button Functions

Display interface and buttons with labels
Figure 8: The display features four buttons: K1 (Power/Menu), K2 (Confirm), K3 (Down/Up), and K4 (Back).
  • K1 (Power/Menu Button): Used to power on/off the protection board (long press) and navigate to the main menu.
  • K2 (Confirm Button): Used to confirm selections.
  • K3 (Down/Up Key): Used to navigate through menu options or switch pages.
  • K4 (Return Key): Used to go back to the previous menu level.

5.2 Initial Activation and Display

After correctly connecting the display to the protection board, press the K1 power button to activate the protection board (after powering on, long press K1 to shut down the protection board). The display interface after startup is shown below:

Initial display screen showing menu options: GROUP, PACKS, SETTING, ABOUT
Figure 9: Initial display screen after startup, showing main menu options.

5.3 Viewing Battery Group Information

To view relevant information about the current battery group:

  1. Operate K3 to align the arrow with the "GROUP" option.
  2. Press K2 to display the battery group information.
Display showing battery group information: Voltage, Current, SOC, Capacity
Figure 10: Example display of battery group information, including voltage (Vtg), current (Cur), state of charge (SOC), and capacity (CAP).

5.4 Viewing Cell Pack Information

To view the voltage of each cell in the current battery pack:

  1. Press K4 to return to the previous menu.
  2. On the main menu, select the "PACKS" option.
  3. Press K2 to display the voltage of each cell. Only 4 cells are displayed per page; use K3 to switch to the next page.

5.5 Configuring CAN/RS485 Protocol Settings

To configure the protection board's CAN/RS485 protocol settings:

  1. On the main menu, select "SETTING".
  2. Press K2 to enter the protocol setting page.
  3. Use K3 to choose between setting the CAN or RS485 protocol.
  4. Press K2 to confirm your selection.
  5. Continue using the K3 navigation key and K2 confirmation key to complete the protocol configuration.
Display showing CAN/RS485 protocol settings and inverter protocol information
Figure 11: Display showing options for setting CAN/RS485 protocol and inverter protocol information.

5.6 Viewing Software Version

To view the current software version information:

  1. On the main menu, select "ABOUT".
  2. Press K2 to enter the About page, which displays the current software version information.
Display showing software version information
Figure 12: Display showing the software version, e.g., "Ver:1.10".

6. Maintenance

To ensure the longevity and optimal performance of your JIKONG JKBMS 3.2 Inch SOC Power Display, follow these general maintenance guidelines:

  • Cleaning: Gently wipe the screen and casing with a soft, dry, lint-free cloth. Avoid using abrasive cleaners, solvents, or aerosol sprays that could damage the display or electronic components.
  • Environmental Conditions: Operate and store the display in a clean, dry environment, away from extreme temperatures, direct sunlight, and high humidity.
  • Connection Integrity: Periodically check all cable connections to ensure they are secure and free from corrosion or damage. Loose connections can lead to intermittent operation or data loss.
  • Firmware Updates: Check the official JIKONG website or contact support for any available firmware updates. Keeping the device updated can improve performance and add new features.
  • Handling: Handle the display with care to prevent physical damage. Avoid dropping the device or subjecting it to strong impacts.

7. Troubleshooting

If you encounter issues with your JIKONG JKBMS 3.2 Inch SOC Power Display, consider the following troubleshooting steps:

  • No Display/Power:
    • Ensure the 12V power supply is correctly connected to the P1 or P2 connector (Pin 1 or Pin 6 respectively, depending on the connector used for power).
    • Verify that the power button (K1) has been pressed and held to activate the protection board.
    • Check the power source for proper voltage and current output.
  • Incorrect Readings:
    • Confirm that the communication cable between the display and the BMS is securely connected to the correct TX/RX pins on both ends.
    • Ensure the CAN/RS485 protocol settings are correctly configured via the "SETTING" menu on the display.
    • Verify that the BMS itself is functioning correctly and providing accurate data.
  • Buttons Unresponsive:
    • Restart the display by powering it off and on again.
    • Ensure there is no physical obstruction preventing button presses.
  • Display shows "Extremely empty" or similar:
    • This message (as seen in Figure 12) might indicate a communication issue or a specific status from the connected BMS. Refer to your BMS manual for interpretation of such messages.

If the problem persists after attempting these steps, please contact JIKONG customer support for further assistance.

8. User Tips

  • Verify Product Received: One user reported receiving an LED bar instead of the 3.2" LCD panel. Always verify that the product received matches your order description and the images in this manual upon delivery.
  • Check Compatibility: Ensure your JIKONG PB Series BMS model is listed as compatible with this 3.2-inch display (e.g., JK-PB1A16S10P V19, JK-PB2A16S30P V19, etc.).
  • Secure Connections: Double-check all wiring connections, especially the communication and power cables, to prevent issues with data display or power supply.
  • Refer to BMS Manual: For detailed interpretation of specific data points or error messages displayed, always consult the user manual for your connected JIKONG PB Series BMS.

9. Warranty and Support

JIKONG products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please refer to the official JIKONG website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

A user manual in PDF format is available for download. You can find it at: JIKONG 3.2-inch Lattice Screen Operation and Maintenance Manual (PDF)

Manufacturing Process

Video: Overview of the manufacturing process for JIKONG BMS boards, showcasing assembly and quality control.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.