DIATONE MAMBA MK5 G4 AIO

Contents

DIATONE MAMBA MK5 G4 AIO Flight Controller and 40A 32Bit 6S ESC User Manual

Model: MAMBA MK5 G4 AIO | Brand: DIATONE

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your DIATONE MAMBA MK5 G4 AIO Flight Controller with integrated 40A 32Bit 6S ESC. Please read this manual thoroughly before use to ensure optimal performance and safety.

Package Contents

Verify that all items are present in your package:

  • DIATONE MAMBA MK5 G4 AIO Flight Controller/ESC Board
  • High Frequency 470uF/35V Capacitor (1x)
  • AIR UNIT sh1.0 Connector (1x)
  • 16AWG 60mm Wires (2x)
  • AMASS Original XT60 Connector (1x)
  • Mounting Hardware (grommets, screws)
Contents of the DIATONE MAMBA MK5 G4 AIO package
Figure 1: Contents of the DIATONE MAMBA MK5 G4 AIO package, including the flight controller, capacitor, XT60 connector, wires, and mounting hardware.

2. Specifications

Flight Controller (FC)

FeatureSpecification
Firmware TargetAlpha (Does NOT support BetaFlight)
MCU170MHz STM32G473
GyroscopeIIM-42652
OSDYes
UARTs4 Sets
Motor Signal Outputs4 Sets
Power LEDYes
LED ControllerYes
AIR UNIT PortYes
Buzzer SupportYes
Input Voltage4~6S Lipo (14.8~25.2V)
BEC ProtectionYes
Receiver ProtectionYes
TVS ProtectionYes
BEC Output10V 2A & 5V 2A
Mounting Size25.5×25.5mm/M2
Overall Dimensions35×34.5×6.5mm

Electronic Speed Controller (ESC)

FeatureSpecification
Input Voltage4~6S Lipo (14.8~25.2V)
Continuous Current40A×4
Burst Current45A (10S)
Firmware TargetBLHeli_32 MAMBA F40_128K
ESC ProtocolDshot300/600/1200/2400
PWM Frequency24~128K
Dimensional drawing of the DIATONE MAMBA MK5 G4 AIO Flight Controller
Figure 2: Dimensional drawing of the DIATONE MAMBA MK5 G4 AIO Flight Controller, indicating mounting hole spacing and overall size.

3. Setup and Installation

Mounting the AIO Board

  1. Ensure your frame has 25.5x25.5mm mounting holes.
  2. Use the provided M2 grommets and screws to securely mount the AIO board to your frame. Ensure the board is oriented correctly according to your flight controller software's default settings or adjust in the software.
  3. Avoid overtightening screws to prevent damage to the board.

Wiring Diagram

Refer to the following diagram for proper wiring connections. Pay close attention to power polarity and signal connections.

Detailed wiring diagram and pinout for the DIATONE MAMBA MK5 G4 AIO Flight Controller
Figure 3: Detailed wiring diagram and pinout for the DIATONE MAMBA MK5 G4 AIO Flight Controller, showing connections for motors, power, UARTs, and peripherals.

Key Connections:

  • Power Input (BAT): Connect your 4-6S Lipo battery directly to the BAT+ and BAT- pads. Solder the provided XT60 connector to the 16AWG wires, then solder these to the board. Ensure correct polarity.
  • Capacitor: Solder the included 470uF/35V capacitor to the main battery pads (BAT+ and BAT-) to filter power noise. Observe polarity.
  • Motors (M1-M4): Connect your ESC motor wires to the corresponding M1, M2, M3, M4 pads.
  • UARTs: Use the available UARTs for connecting peripherals such as your receiver, VTX, GPS, etc. Refer to the diagram for specific TX/RX pins.
  • AIR UNIT Port: Dedicated port for digital FPV systems.
  • Buzzer: Connect a buzzer to the BZ+ and BZ- pads for audible alerts.
  • LED: Connect compatible LED strips to the LED pad.

Firmware Flashing

IMPORTANT: This AIO board ONLY supports Alpha firmware. It is NOT compatible with BetaFlight.

  1. Download the latest Alpha firmware for the STM32G473 MCU.
  2. Connect the AIO board to your computer via the USB-C port.
  3. Use the appropriate Alpha firmware configurator software to flash the firmware.
  4. After flashing, perform a full chip erase and calibrate the accelerometer.

4. Operating Instructions

Initial Configuration

  1. After flashing Alpha firmware, open the Alpha configurator.
  2. Configure your receiver type (e.g., SBUS, CRSF, ELRS) and connect it to the appropriate UART.
  3. Set up your motor protocol (Dshot300/600/1200/2400). Dshot600 is a common starting point.
  4. Calibrate your ESCs if necessary, though Dshot protocols typically do not require manual calibration.
  5. Configure OSD settings, VTX settings, and any other peripherals connected to the board.
  6. Perform motor direction tests in the configurator to ensure motors spin in the correct direction for your frame type.

Powering On

Once all connections are secure and configurations are complete, connect your 4-6S Lipo battery. The board should power on, and any connected LEDs or buzzers should indicate readiness. Always ensure propellers are removed during initial power-on and testing.

5. Maintenance

  • Regular Inspection: Periodically check all solder joints and connections for looseness or corrosion.
  • Cleaning: Keep the board free from dust, dirt, and debris. Use compressed air or a soft brush. Avoid using liquids directly on the board.
  • Physical Damage: Inspect for any cracks, bent pins, or other physical damage, especially after crashes.
  • Firmware Updates: Check for official Alpha firmware updates periodically to benefit from bug fixes and new features.

6. Troubleshooting

Common Issues and Solutions:

  • No Power/Board Not Lighting Up:
    • Check battery connection and polarity.
    • Verify the Lipo battery is charged and within the 4-6S voltage range.
    • Inspect for any short circuits on the board or connected components.
  • Motors Not Spinning/Erratic Behavior:
    • Ensure ESC protocol (Dshot) is correctly configured in Alpha firmware.
    • Check motor signal wire connections to the AIO board.
    • Verify motor direction in the configurator.
    • Inspect motors and propellers for damage.
  • No Connection to Alpha Configurator:
    • Ensure the correct USB-C cable is used and connected securely.
    • Install necessary USB drivers for the STM32 microcontroller.
    • Try a different USB port or computer.
    • Ensure the board is not powered by the Lipo battery while connecting via USB, unless specifically required for certain operations.
  • Peripherals Not Working (Receiver, VTX, GPS):
    • Verify correct wiring to the designated UARTs.
    • Ensure the UARTs are enabled and configured correctly in the Alpha firmware.
    • Check baud rates and protocols for each peripheral.
  • Board Overheating:
    • Ensure adequate airflow around the board.
    • Check for any short circuits or excessive current draw from motors/ESCs.
    • Verify that the BEC output is not overloaded by connected devices.

User Tips:

  • Always double-check solder joints for cold joints or bridges before powering on.
  • Use a smoke stopper for the first power-up after any new build or significant wiring changes to prevent damage.
  • Keep your Alpha firmware updated for the best performance and stability.
  • When troubleshooting, isolate components by disconnecting non-essential peripherals to pinpoint the issue.

7. Warranty and Support

For technical support, firmware updates, or warranty inquiries, please contact the manufacturer, DIATONE, or your authorized reseller. Keep your proof of purchase for warranty claims.

© 2024 DIATONE. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.