1. Product Overview
This module is a 3.2-inch graphical LCD display specifically designed for energy storage battery management systems (BMS). It features a 128×64 resolution dot-matrix blue screen LCD and has a built-in TTL communication interface. Users can view key parameters such as current battery voltage, current, and state of charge (SOC) via buttons, and also configure the protection board's CAN/RS485 protocol settings through the buttons.
The display is compatible with the following JIKONG V19 PB Series BMS models:
- JK-PB1A16S10P V19
- JK-PB1A16S15P V19
- JK-PB2A16S15P V19
- JK-PB2A16S20P V19
- JK-PB2A16S30P V19


Manufacturing Process
The following video provides an insight into the manufacturing process of JIKONG products, highlighting the quality and precision involved in producing components like the 3.2-inch SOC Power Display.
2. Setup and Installation
2.1 Package Contents
Ensure all items are present in the package:
- 1 x JIKONG 3.2-inch Display
- 1 x Connection Cable

2.2 Interfaces and Cables
The display features two main interfaces for connection:
- **P1 (Activation Switch Interface GH1.25-6P):** Used for connecting an activation switch.
- **P2 (User Interface HY2.0-6P):** Used for communication with the BMS.

2.3 Wiring Diagram and Connection
To connect the display to your JIKONG V19 PB Series BMS:
- Connect one end of the provided cable to the user interface (P2) of the display screen.
- Connect the other end of the cable to the TTL communication interface of the protection board (BMS).
Important: There is no need to distinguish the direction of the cable connection to the TTL communication interface.
P1 Interface Definition (Activation Switch)
| Serial Number | Explanation |
|---|---|
| 1 | VIN, connected to 12V power supply |
| 2 | Connect to protection board TX (RXD, connected to the TX of the protection board) |
| 3 | Connect to protection board RX (TXD, connected to the RX of the protection board) |
| 4 | GND, ground connection |
| 5 | Connect to the positive terminal of the switch (K+) |
| 6 | Connect to the negative terminal of the switch (K-) |
P2 Interface Definition (User Interface)
| Serial Number | Explanation |
|---|---|
| 1 | Connect to the negative terminal of the switch (K-) |
| 2 | Connect to the positive terminal of the switch (K+) |
| 3 | GND, ground connection |
| 4 | Connect to protection board RX (TXD, connected to the RX of the protection board) |
| 5 | Connect to protection board TX (RXD, connected to the TX of the protection board) |
| 6 | VIN, connected to 12V power supply |
3. Operating Instructions
3.1 Button Functions
The display features four buttons for navigation and control:
- **K1:** Power button / Menu button
- **K2:** Confirm button
- **K3:** Down key (for navigation)
- **K4:** Return key (Back button)
3.2 Initial Activation
After correctly connecting the display to the protection board (BMS), long press the K1 power button to activate the protection board. The display interface after startup will show the main menu.

3.3 Navigating the Display
Use the K3 button to move the cursor (arrow) between menu options. Press K2 to confirm your selection.
Viewing Battery Group Information (GROUP)
From the main menu, use K3 to select "GROUP" and press K2. The display will show relevant information about the current battery group, including voltage (Vtg), current (Cur), state of charge (SOC), and capacity (CAP).

Viewing Cell Pack Information (PACKS)
From the main menu, use K3 to select "PACKS" and press K2. The display will show the voltage value of each cell in the current battery pack. Only 4 cells are displayed per page; use K3 to switch to the next page to view more cells.

Setting CAN/RS485 Protocol (SETTING)
From the main menu, use K3 to select "SETTING" and press K2 to enter the protocol setting page. In this page, use K3 to choose between setting the CAN or RS485 protocol, then press K2 to confirm. Continue using the K3 navigation key and K2 confirmation key to complete the protocol configuration.

Viewing Software Version (ABOUT)
From the main menu, use K3 to select "ABOUT" and press K2 to enter the About page, which displays the current software version information (e.g., Ver:1.10).
4. Maintenance
This manual primarily covers the operation and basic structure of the JIKONG 3.2-inch SOC Power Display. Specific maintenance procedures beyond general care (e.g., keeping the device clean and dry) are not detailed in the provided documentation. For advanced maintenance or repairs, please contact JIKONG customer support.
A detailed PDF manual, titled "3.2-inch Lattice Screen Operation and maintenance manual", is available for download from the manufacturer or seller's website. This document contains further information on the product's operation and structure.
5. Troubleshooting
No specific troubleshooting steps are provided in the available documentation. If you encounter issues with your JIKONG 3.2-inch SOC Power Display, please ensure all connections are secure and the device is powered correctly. If problems persist, refer to the Warranty and Support section for assistance.
6. Specifications
| Feature | Specification |
|---|---|
| Brand Name | JIKONG |
| Model | JK33 |
| Type | LIFEPO4 Battery BMS Display |
| Handware or Smart | SMART BMS (Display for) |
| Balance Function | Active Balanced BMS (Display for) |
| Charge and Discharge Port | Common Port BMS (Display for) |
| Charging Current | 10A (BMS specification, display shows data) |
| Usage Scenario | Power BMS, Energy Storage BMS, 3C Digital BMS |
| Function | Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection (BMS functions, displayed on screen) |
| Certification | CE |
| Display Size | 3.2 inch |
| Display Type | 128x64 Dot-Matrix Blue Screen LCD (LCD-12864-TTL) |
| Communication Interface | TTL |
| Supported BMS Models | JK-PB1A16S10P V19, JK-PB1A16S15P V19, JK-PB2A16S15P V19, JK-PB2A16S20P V19, JK-PB2A16S30P V19 |
6.1 Mechanical Dimensions


7. User Tips
- Always ensure the display is compatible with your specific JIKONG V19 PB Series BMS model before connecting. Refer to the compatibility list in Section 1.
- When connecting the communication cable, ensure it is firmly seated in both the display's P2 port and the BMS's TTL communication interface.
- If the display does not power on after connection, double-check the wiring and ensure the BMS is active. A long press on K1 is required for initial activation.
8. Warranty and Support
For warranty information, technical support, or service inquiries regarding your JIKONG 3.2-inch SOC Power Display, please contact the manufacturer or your authorized seller directly. Ensure you have your product model (JK33) and any relevant purchase details available when seeking support.