BAJETON BJ-9000

Contents

BAJETON BJ-9000 Multi-Band Handheld Radio User Manual

Model: BJ-9000

Introduction

This manual provides detailed instructions for the safe and efficient operation of your BAJETON BJ-9000 Multi-Band Handheld Radio. Please read this manual thoroughly before using the device and keep it for future reference.

BAJETON BJ-9000 Walkie Talkie with display showing frequencies and features like APRS, CB/SSB/HF, Cross Band Repeater, NOAA, Bluetooth Programming.

Figure 1: BAJETON BJ-9000 Multi-Band Handheld Radio Overview

Getting to Know Your Device

Device Layout

Diagram of BAJETON BJ-9000 showing custom buttons PF2 and PF3 with functions like PTT, MONI, RADIO, Beacon TX, SOS, Scan, Search, Spectrum.

Figure 2: Customizable Side Buttons and Functions

The BAJETON BJ-9000 features a Channel Knob, Power Switch/Volume Knob, PPT A/B/C Buttons, Side Key 2, Speaker, Function Keypad, and Numeric Keypad. It also includes an Accessory Interface and a 2.4-inch HD Large Colorscreen Display.

Key Functions

No.ButtonFunction
①OKMenu Select / Confirm Key. Long press to enter spectrum mode.
②A/B/CShort press to switch between A/B/C segments. Long press to enter remote sub-tone scan mode.
③Direction KeysNavigation keys.
④Exit/ClearShort press: Exit / Clear Key. Long press to enter frequency sweep mode.
⑤V/MShort press: Switch between Channel Mode and Frequency Mode. Long press to enter the APRS positioning interface.
⑥Number Keys (0-9)In standby state: In Frequency Mode, used to set the working frequency; in Channel Mode, used to switch channel. After quick setup, long pressing keys 0-9 allows fast access to the assigned functions.

Interface Icons

IconDescription
VOXVoice-Activated Transmission enabled.
APRSAutomatic Packet Reporting System enabled.
MOMonitor function enabled.
TWTri-Watch Active (monitors 3 channels simultaneously).
Keypad LockKeypad is locked. Long press '#' to unlock.
RSSISignal Strength indicator.
GPSGPS positioning with status icon.
ZRepeater Mode ON.
BluetoothBluetooth Enabled.
BatteryBattery Status. Flashing indicates low battery.
Power SaveEnergy-saving mode active.
H/M/LHigh/Medium/Low Power Indicator.
N/WNarrowband/Wideband Mode Indicator.
+/-Frequency Mode (+/- Frequency Offset).
RFrequency Invert (RX/TX frequencies inverted).
TSimplex communication (identical TX/RX frequencies).
EncryptionEncryption function activated.
AMAM (Amplitude Modulation) demodulation mode.
SCRScrambler Function (voice encryption).

Setup

Battery and Antenna Installation

Ensure the battery is properly installed and charged before use. The original antenna has a frequency range of FM/136-174/400-470MHz. If you need to use frequencies beyond this range, you must purchase a specialized antenna separately that is compatible with the desired frequency range (e.g., a 27MHz CB antenna for 27MHz frequency).

Charging Instructions

  1. Dock Charging (Optional): Insert the battery pack or the radio with the battery pack into the charging dock. Ensure proper contact with the charging terminals of the dock.
  2. Type-C Charging: Connect the provided charging cable to the power adapter and plug the power adapter into an AC power outlet. Insert the charging cable into the Type-C interface of the main unit's battery.
  3. Charging Indicator: When the device is charging, the red indicator light indicates charging in progress. The green indicator light indicates charging is complete.
BAJETON BJ-9000 Walkie Talkie showing NOAA Weather Radio and FM Radio features.

Figure 3: NOAA Weather Radio and FM Radio Features

Bluetooth APP Programming

The BAJETON BJ-9000 supports Bluetooth programming via a mobile application. This allows for convenient and fast frequency input and adjustment without complex cables.

  1. Download the programming application by scanning the QR codes provided below for iOS or Android devices.
  2. Pair your mobile device with the radio via Bluetooth.
  3. Use the app to input and adjust frequencies and other settings.
QR codes for downloading the Bluetooth Programming APP for iOS and Android.

Figure 4: Bluetooth Programming App QR Codes

APRS/GPS Configuration

The radio features built-in APRS and GPS for real-time location sharing and monitoring.

  1. Open the menu and select 'APRS Set'.
  2. Enable APRS and GPS, and determine the time zone.
  3. Choose 'Fixed Position' or 'GPS Position' as needed for beacon setup.
  4. Customize the side keys for quick access to APRS functions if desired.

Video 1: Demonstration of APRS and GPS Setup

Wireless Copy Frequency

This feature allows you to instantly copy frequency and CTCSS from another radio, simplifying operations.

Two BAJETON walkie talkies demonstrating the Wireless Copy Frequency feature.

Figure 5: Wireless Copy Frequency in action

Operating Instructions

Power On/Off and Volume Control

Rotate the Power Switch/Volume Knob clockwise until a "click" is heard to power on. Rotate counterclockwise until a "click" is heard to power off. Rotate clockwise to increase volume and counterclockwise to decrease volume.

Menu Navigation

From the home screen, briefly press the OK key to enter the menu. Use the arrow Direction keys to navigate. Press OK again to confirm selections. Press Exit/Clear to exit the menu.

Primary/Secondary Frequency Toggle

On the standby screen, briefly press the A/B/C key to select the primary frequency highlighted in blue background. Non-highlighted frequencies are secondary.

Channel Mode / Frequency Mode Toggle

On the standby screen, briefly press the V/M key to switch between frequency mode and channel mode. Note: If no valid channels are stored, switching to Channel Mode is disabled.

Voice-Activated Transmission (VOX) Function

To enable VOX, navigate to Menu → VOX. When enabled, the radio automatically enters transmit mode if the microphone detects sufficient sound input. Adjust the VOX sensitivity level via menu settings. VOX delay time must be configured to maintain transmission continuity.

Sweep Function

Assign a side key function as "Sweep" or long-press Exit/Clear to quickly enter sweep mode. It detects the transmitter's carrier frequency and CTCSS/DCS (sub-tone) information, displaying them on the screen. Once the carrier frequency is detected, press the OK key to save the scanned frequency to a specified channel list. Supported Ranges: VHF: 136-174 MHz, UHF: 400-520 MHz.

Repeater Setup

The BJ-9000 features a Cross Band Repeater function, allowing interconnection between different frequency bands (e.g., U/V bands) to extend communication range.

Diagram illustrating the Cross Band Repeater function, showing U trans U and U trans V modes.

Figure 6: Cross Band Repeater Functionality

  1. Activating Repeater Mode: Menu → Radio → AB RPT-Mode → ON. The standby screen will display the repeater icon Z.
  2. Repeater Requirements: Devices enabling the relay function must operate on different frequency bands.
  3. Repeater Direction Logic: In default standby, both primary and secondary frequencies act as receivers. If the primary frequency receives a valid carrier signal, the secondary frequency automatically becomes the cross-band transmitter. The same applies if the secondary frequency receives a valid carrier signal, making the primary frequency the cross-band transmitter.
  4. Speaker Audio Control: Configurable option to enable/disable local speaker audio during repeater operation.

Emergency SOS Function

Assign a side key as the [Emergency Alarm] button. Operation: Menu → Radio → SOS Mode.

  • Local Alarm: The device sounds an alarm tone locally without transmitting any signal.
  • Transmit Alarm Tone: Broadcasts the alarm tone via signal transmission.
  • Transmit Alarm Code: Sends the alarm code through signal transmission.

CTCSS/DCS Settings

Operation: Menu → CTCSS/DCS. Select desired DCS code or CTCSS frequency. This function enables selective call reception by filtering out unwanted noise signals.

Scan Function

Configure via Menu → Radio → Scan Mode. You can set a side key as the Scan Key.

  • Channel Mode: Scans channels listed in memory (requires power-on scan to add).
  • Frequency Mode: Scans frequencies based on the selected step setting.
  • Time Mode: Resumes scanning if no operation is performed within 5 seconds after detecting a carrier signal.
  • Carrier Mode: Stops scanning upon detecting a carrier signal and resumes scanning 5 seconds after the carrier disappears.
  • Search Mode: Stops scanning immediately upon detecting a carrier signal.

PTT-ID Function

DTMF transmit identity S-CODE or PTT-ID. Call Codes (15 preset groups): Menu → Signaling → S-CODE. Assign unique call codes to each segment (A/B/C) or signal type. ID Code Setup: Menu → Signaling → PTT-ID.

  • Send on Press: After pressing the PTT, the call code/identity code is sent first, followed by the voice signal.
  • Send on Release: After releasing the PTT, the call code/identity code is sent, then the transmission ends.
  • Send Both: The call code/identity code is sent both when the PTT is pressed and released.

FM Radio Function

Customize a side key as a radio shortcut or long-press a number key to enter radio mode.

  1. Short press OK to access the radio menu and select modulation mode. Set the radio frequency directly using the numeric keys.
  2. In radio mode, press V/M to toggle between Frequency Mode (VFO) and Channel Mode (MR).
  3. In Frequency Mode, short press the # key to activate auto-scan for stations.

Spectrum Analyzer

The built-in Spectrum Analyzer provides rich spectrum information and analysis functions to help identify signal interference and improve communication quality.

BAJETON BJ-9000 Walkie Talkie next to a spectrum analyzer device, illustrating its spectrum analysis capability.

Figure 7: Spectrum Analyzer Feature

Maintenance

Daily Maintenance

  • Do not pierce or scratch the product with hard objects.
  • Do not store the product in environments containing chemical corrosive substances.
  • Do not carry or use the product by pulling the earphone cable.
  • When not using the earphone jack, cover the interface with the protective cap.

Cleaning Procedure

Before cleaning, please power off the device and remove the battery:

  1. Regularly use a dry, clean, lint-free cloth or a soft brush to remove dust from the product surface and charging terminals.
  2. If the buttons or casing become dirty, use a neutral detergent and a non-woven cloth for cleaning. Do not use detergents, alcohol, sprays, or petroleum-based chemicals as they may damage the surface casing.
  3. After cleaning, ensure the product is completely dry before use.

Troubleshooting

If you encounter issues with your BAJETON BJ-9000, consider the following:

  • No Power: Ensure the battery is fully charged and properly installed. Check the power switch.
  • Poor Contact with Data Cable: If using a data cable for programming, ensure the connector is securely seated. If the screws are too long, causing the connector to float, consider using a 1mm thick washer to ensure proper contact.
  • Programming Issues: Verify that you are using the correct programming software and firmware. Using firmware from other brands may cause damage. Ensure the Bluetooth connection is stable if programming wirelessly.
  • No Signal/Poor Reception: Check that the antenna is securely attached and is compatible with the frequency range you are using. Ensure you are within range of other radios or repeaters.

Specifications

FeatureSpecification
Brand NameBAJETON
Model NumberBJ-9000
Walkie Talkie TypePortable
Output Power (W)10W-25W (Tri-power: 1W, 5W, 10W adjustable)
Maximum Range5km-10km
Frequency Range (TX)CB: 27MHz, 18-64MHz, 136-520MHz
Frequency Range (RX)CB: 27MHz, FM: 64-108MHz, SW: 2.3-30MHz, MW: 520-1710KHz, LW: 153-279KHz, 18-620MHz, 840-999MHz (AM/FM/SSB)
Display2.4 Inch HD Large Colorscreen, Yes
Memory ChannelsUp to 960 named memory channels
Battery2800mAh Rechargeable Li-ion Battery, Included
Waterproof / Water-ResistantNo
OriginMainland China
Package Dimensions26cm (L) x 22cm (W) x 7cm (H)
Package Weight0.76 kg
BAJETON BJ-9000 Walkie Talkie with a 2.4-inch HD large color screen display, highlighting up to 960 named memory channels and VOX feature.

Figure 8: High-Definition Color Screen and Memory Channels

BAJETON BJ-9000 Walkie Talkie demonstrating 10W Tri-power output (1W, 5W, 10W) with a city skyline background.

Figure 9: Adjustable Tri-Power Output

User Tips

  • Firmware Compatibility: Some users have reported success with firmware updates using Radtel RT-950 Pro firmware due to similar hardware. However, proceed with caution as using unofficial firmware may void your warranty or damage the device.
  • Data Cable Connection: If you experience poor contact with the data cable during programming, check the length of the connector screws. If they are too long, causing the connector to float, inserting a 1mm thick washer can help ensure a secure connection.
  • Antenna Matching: Always ensure your antenna is compatible with the frequency range you intend to use for optimal performance. Specialized antennas are required for frequencies outside the standard FM/136-174/400-470MHz range.

Warranty and Support

Warranty Terms

The warranty period for this product starts from the date of sale. The main unit is covered for 12 months, and the battery and charging accessories are covered for 6 months. Paid repair services will be required for cases such as:

  • Failure to present the warranty card and purchase invoice.
  • Alteration of the warranty card or mismatch with the product.
  • Defects and damages caused by using the product under non-standard conditions.
  • Defects and damages caused by misuse, accidents, water ingress, or negligence.
  • Defects and damages resulting from improper testing, operation, repair, installation, modification, or adjustment.
  • Defects and damages caused by unauthorized repairs or disassembly.
  • Defects and damages caused by force majeure.
  • Normal wear and tear from regular use.

For detailed warranty information, please refer to the Product Warranty Card included with your purchase.

Additional Resources

A user manual in PDF format is available for download. This document provides further detailed instructions and specifications.

View User Manual (PDF)


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.