1. Product Overview & Features
This professional 30W shortwave power amplifier board covers the entire 3-28MHz HF band, specifically optimized for CW (Continuous Wave) and SSB (Single Side Band) amateur radio modes. It features automatic transmit/receive switching with clear LED status indicators (green for receive/power, red for transmit). The amplifier is designed to boost the output of QRP transceivers. With a 1.5W input, it delivers approximately 30W PEP output at 7MHz. The board includes an integrated heatsink for basic thermal management, though a cooling fan is recommended for prolonged operation.
Key Features at a Glance
- Full HF Band: 3-28 MHz coverage
- 30W Output: PEP at 7MHz, 13.8V
- Auto TR Switch: Seamless TX/RX transition
- QRP Driver: 0.5-3W input range
- Heatsink Included: Fan recommended for sustained use
- LED Status: Green (RX) / Red (TX)
2. Safety & Warnings
CRITICAL SAFETY – READ BEFORE USE
- RF radiation hazard: This amplifier can output up to 30W of RF power. Ensure proper antenna connection and never operate without a suitable load (50Ω dummy load or antenna).
- Heat hazard: The amplifier generates significant heat during operation – the heatsink may reach high temperatures. Allow cooling between transmissions.
- Power supply: Use a stable 12-13.8V DC supply capable of delivering at least 6A continuous. Voltage spikes may damage the amplifier.
- Input power limit: Do not exceed 3W input – over-driving will cause distortion and may destroy the final transistors.
- Mode restriction: This amplifier is designed for CW and SSB only. Do not use with FM, AM, or digital modes – continuous carrier modes will overheat and damage the unit.
- Impedance matching: All RF connections must be 50Ω – mismatched loads cause high VSWR and can damage the amplifier.
General Warnings
- This product is intended for amateur radio operators with appropriate knowledge of RF systems.
- Always connect the antenna or dummy load before applying power.
- Do not operate the amplifier without the heatsink – ensure adequate airflow.
- Keep the amplifier away from moisture, dust, and flammable materials.
- Ensure the enclosure is properly grounded for safety.
WARNING: The input and output must be plugged in before powering on. Otherwise, the chip will be burned because reflected signal is too large. Improper operation is the user's responsibility.
3. Technical Specifications
| Parameter | Value |
|---|---|
| Product Name | 30W Shortwave Power Amplifier Board (3-28MHz, CW/SSB) |
| Model Number | PA-30W-HF-V1 |
| Brand Name | DykbRadio |
| Frequency Range | 3-28 MHz |
| Recommended Input Power | 0.5-3 W |
| Output Power (PEP) | 30W (typical @ 7MHz, 13.8V, 1.5W input); 10W (with 0.5W PIXIE drive) |
| Operating Voltage | 12-13.8V DC (nominal) |
| Current Consumption | ≤ 6A (maximum) |
| Compatible Modes | CW, SSB only (not FM/AM/digital) |
| Input/Output Impedance | 50 Ω |
| TR Switching | Automatic (RF sensing) |
| LED Indicators | Green (power/RX) Red (TX) |
| Heat Management | Heatsink included (fan optional, not included) |
| PCB Dimensions (with heatsink) | 9 × 5 × 3.4 cm |
| Weight | 200 g |
| Operating Temperature | 0°C - 40°C |
| Certifications | CE, RoHS |
4. Setup & Connection
4.1 Connection Diagram


4.2 Connection Steps
- RF Input: Connect your QRP transceiver (0.5-3W output) to the RF IN port (SMA or BNC – check connector type).
- RF Output: Connect a 50Ω antenna or dummy load to the RF OUT port.
- Power Supply: Connect 12-13.8V DC (≥6A) to the power input terminals (observe polarity).
- Ground: Connect the amplifier's ground terminal to your station ground for safety.
5. Operation
5.1 Basic Operation
- The amplifier is automatically enabled when RF input is detected – the red LED will light up during transmission.
- In receive mode (no RF input), the amplifier bypasses the signal path – the green LED remains lit.
- For best performance, adjust your transceiver's drive level so that the amplifier outputs a clean, undistorted signal.
- Monitor the heatsink temperature – if it becomes too hot to touch, allow cooling or add a fan.
5.2 LED Indicators
- Green LED: Power on / receive mode.
- Red LED: Transmit mode (lights when RF input is present).
5.3 QRP Driver Examples
- PIXIE transceiver (≈0.5W input): Output ≈10W.
- Frog Sound kit (≈1.5W input): Output ≈30W (at 7MHz, 13.8V).
- Other QRP transceivers within 0.5-3W range will work proportionally.
5.4 Operational Video
6. Maintenance & Storage
6.1 Cleaning
- Disconnect power and antenna before cleaning.
- Use a soft, dry brush to remove dust from the heatsink.
- Do not use solvents or liquids.
6.2 Storage
- Storage Environment: Store in a dry, dust-free place at 15°C – 35°C. Avoid direct sunlight and high humidity.
- Long-term storage: No special precautions – but keep in an anti-static bag if possible.
- Periodic Checks: Inspect the heatsink for dust accumulation and connectors for corrosion every 6 months.
7. Troubleshooting
- No output power: Check input signal (should be 0.5-3W). Verify power supply (12-13.8V, ≥6A). Check antenna/load connection.
- Red LED not lighting on transmit: Input power may be too low (<0.5W). Adjust drive level from transceiver.
- Overheating: Reduce transmission time or add a cooling fan. Ensure heatsink is not blocked.
- Distorted output: Input power may be too high (>3W). Reduce drive level. Also check for mismatched load.
- Amplifier not switching to receive: The TR switch is RF-sensing – if there is residual RF, it may stay in TX mode. Check transceiver output.
8. Compliance Information
This amplifier complies with the following directives:
- CE Marking: Complies with EMC Directive 2014/30/EU and LVD 2014/35/EU (as a component).
- RoHS: Compliant with 2011/65/EU.
- REACH: Does not contain SVHCs above 0.1% (w/w).
CE Height ≥ 5 mm
Certification Marks: CE, RoHS
9. Package Contents
- 1 × Assembled amplifier board with heatsink
- (Cables, connectors, and fan not included)
10. User Tips
- Pre-Power On Check: Always ensure both input and output connections are securely plugged in before applying power to prevent damage from reflected signals.
- Performance at Different Frequencies: The amplifier can provide approximately 28 watts at 7 MHz and around 18 watts at 28 MHz, which is suitable for many amateur radio needs.
- Heatsink and Cooling: The product includes a heatsink for basic thermal management. For sustained operation, especially during longer transmissions, it is highly recommended to add an external cooling fan (not included) to prevent overheating.
11. Disposal & Recycling
This product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health. Please follow local electronic waste regulations.
For regions outside the EU, please comply with local disposal regulations.
12. Manufacturer & Support
Manufacturer: Shenzhen Trading Co., Ltd.
Address: 202, Building S, Maoyuan Industrial Park, Huanguan South Road, Guanlan Street, Longhua District, Shenzhen City, Guangdong Province, China
Email: 1241273859@qq.com
EU Authorized Representative: MJCM SARL
Address: 78 avenue des Champs Elysees, Bureau 326, France
Email: mjcm190928@gmail.com
For further assistance or inquiries, please contact the manufacturer or authorized representative directly.
A user manual PDF is available for download: User Manual (PDF)