LUMDEER HT-16

Contents

LUMDEER HT-16 Road Bicycle Turn Signal Helmet User Manual

Model: HT-16

1. Introduction and Safety Instructions

This product complies with the essential health and safety requirements set out in Regulation (EU) 2016/425 Personal Protective Equipment. The helmet meets requirements of the Harmonized Standards EN 1078:2012+A1:2012 and CPSC 16 CFR Part 1203.

General Safety Guidelines

  • The helmet can only provide protection if it fits well. Ensure the helmet feels secure and comfortable on your head.
  • Adjust the helmet so that the straps do not cover the ears, the buckle is positioned away from the jawbone, and both straps and buckle are comfortable and firm.
  • The helmet must be positioned on the head to protect the forehead and not be pushed too far over the back of the head.
  • A helmet cannot always protect against injury.
  • A helmet subjected to a severe impact must be discarded and destroyed immediately.
  • Do not modify or remove any original component parts of the helmet.
  • Do not adapt the helmet for fitting accessories in a way not recommended by the manufacturer.

WARNING! This helmet should not be used by children while climbing or doing other activities when there is a risk of strangulation/hanging if the child gets strapped with the helmet.

WARNING! No helmet can prevent all head injuries. Even in low-speed accidents, serious injury or death can occur. For best protection, the helmet must be fitted and attached properly to the head in accordance with the fitting instructions. Destroy and replace the helmet after impact. Protection may not be adequate in future impacts as damage can be invisible. Do not clean with solvents, bleaches and strong detergents. They can damage the helmet, sometimes invisibly. Use mild soap and water only. Read the instruction manual for more specific care and cleaning information.

A detailed user manual in PDF format is available for download here.

2. Setup and Adjustment

Proper fit and adjustment are crucial for the helmet's protective function.

2.1. Helmet Components and Fit System

The HT-16 helmet features a comfortable fit system with a knob-type adjustment for precise head circumference adaptation.

Diagram showing helmet adjustment system, wearing method, webbing system, and wearing direction.

Image: Visual guide for helmet adjustment, wearing method, webbing system, and correct wearing direction.

2.2. Adjustment Steps

  1. Head Circumference Adjustment: Use the rotary adjuster at the back of the helmet to tighten or loosen the internal retention system. Turn the knob clockwise to tighten and counter-clockwise to loosen until the helmet fits snugly and comfortably without excessive pressure.
  2. Strap Adjustment: Ensure the side straps form a 'V' shape just below your ears. Adjust the strap length using the buckles to achieve a snug fit under your chin, ensuring the helmet cannot be easily pulled forward or backward.
  3. Chin Pad: Position the comfortable chin pad under your chin and secure the convenient buckle.

Caution! If you are unable to adjust the size of the helmet so that it can only be moved slightly forward or backward with the straps closed, do not use it! Exchange the helmet for a smaller or different model.

2.3. Attaching Magnetic Goggles and Sun Visor

The helmet is equipped with a detachable brim and magnetic goggles. These can be easily attached or removed to adapt to different light conditions and environments.

  • Magnetic Goggles: Align the magnets on the goggles with the corresponding points on the helmet and allow them to snap into place.
  • Sun Visor: Attach the visor brim to the designated slots on the front of the helmet.
Diagram illustrating helmet features including HD anti-fog lens, visor brim, removable lining, and rotary adjuster.

Image: Detailed view of helmet features including the HD anti-fog lens, visor brim, removable lining, and rotary adjuster.

3. Operating Instructions

The LUMDEER HT-16 helmet features an intelligent lighting safety system for enhanced visibility and communication during your ride.

Detailed diagram of HT-16 helmet features including LED headlight, magnetic HD lenses, remote control, USB charging port, tail light switch, left/right turn signals, 10 air vents, and head circumference adjuster. Also shows headlight and taillight modes.

Image: Overview of HT-16 helmet details, including lighting components and controls.

3.1. Intelligent Lighting System

The helmet integrates a headlight, taillight, and turn signals, all controlled by a handlebar-mounted remote.

  • LED Headlight: Provides front illumination for visibility.
  • Rechargeable Taillight: Enhances rear visibility and includes turn signal functionality.
  • Remote-Controlled Brake Taillight: Automatically brightens during deceleration to alert following traffic.

3.2. Remote Control Operation

The handlebar remote control allows for easy switching of lighting modes.

  • Headlight Modes:
    • Always on white light mode
    • Red light flashing mode
  • Taillight Modes:
    • Breathing pattern
    • Flashing pattern
    • Horse racing mode
    • Always on mode
  • Turn Signals: Use the remote to activate left or right turn signals.

3.3. Charging

The helmet's lighting system is powered by a rechargeable battery. Use the provided USB charging cable to charge the helmet. The USB charging port is located on the helmet.

4. Maintenance

4.1. Cleaning

  • Clean your helmet only with lukewarm water, mild soap, and a soft cloth.
  • First, remove the comfort padding.
  • Gently wipe the interior and exterior surfaces of the helmet with the damp cloth.
  • The comfort padding can be hand washed using lukewarm water and mild soap. After washing, allow the padding to air dry completely before reinserting.
  • Maximum number of Cleaning cycles before Disposal: It is recommended to clean once every 1-2 months, with a maximum cleaning frequency of no more than 50 times.

4.2. Storage

  • Allow your helmet to air dry after each use.
  • Store your helmet in a cool, dry place.
  • High temperatures, starting at 60°C, can seriously damage the helmet. Uneven surfaces and blistering are signs of such damage.
  • Do not store the helmet behind glass, such as in a car, or near heating sources.

4.3. Obsolescence

A helmet must be replaced if it no longer fits properly or, at the latest, 6 years after the date of manufacture, even if no damage is visible. Your helmet must be regularly inspected for any visible defects. A helmet subjected to a severe impact or deep scratch must be discarded and destroyed, as it loses its protective function.

5. Specifications

LUMDEER HT-16 Helmet Specifications
AttributeDetail
Product NameSmart Road Cycling Helmet
BrandLUMDEER
Model NumberHT-16
MaterialPC shell + EPS inner core
Weight (g)Approx. 400g (Size L)
Head SizeL (Head circumference 57-62cm)
Air Vents10 ventilation holes
CertificationCE, CPSC
CharacteristicChargeable front and rear taillights, turn signals, Magnetic lens
UsageRacing/road/mountain/pulley, Bicycles, scooters, roller skates, balance bikes
Package IncludesHelmet x1, Remote control x1, Power cord x1, Black Visor x1, User Manual x1, Helmet bag x1
Product Parameters table with dimensions and standard configuration.

Image: Product parameters including weight, head size, number of vents, and standard configuration.

What's in the box diagram showing the helmet, black visor, remote controller, USB charging cable, user manual, and helmet bag.

Image: Contents of the product package.

6. Troubleshooting

This section provides general guidance for common issues. For specific technical problems, please refer to the official PDF manual or contact customer support.

  • Lights not working: Ensure the helmet is fully charged. Check the remote control battery if applicable. Verify that the lights are turned on via the remote.
  • Remote control unresponsive: Check the remote control battery. Ensure it is paired correctly with the helmet (if pairing is required, refer to the PDF manual).
  • Helmet feels loose after adjustment: Re-adjust the rotary knob and chin straps. If the helmet still does not fit securely, it may be the wrong size and should be replaced.
  • Magnetic goggles not attaching: Ensure the magnets on both the goggles and helmet are clean and free from debris.

7. Warranty and Support

For warranty information, returns, or technical support, please refer to the seller's policies or contact the LUMDEER Official Store directly. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.