1. Product Overview
The FLYWING MH-60R Seahawk is a 470-size scale RC helicopter equipped with an advanced multi-link GNSS system, supporting GPS, BDS, GLONASS, and GALILEO for stable outdoor hovering. It features an ACE Flight Controller, LED indicator lights, and offers one-button return-to-home (RTH) and low-battery RTH functions. With a maximum flight time of approximately 18 minutes and a communication distance of up to 1KM in non-interference environments, this helicopter provides a realistic and engaging flight experience for various skill levels.
The MH-60R Seahawk is a highly detailed model, featuring enhanced rivet and panel line details, a simulated four-blade metal propeller, and a restored paint scheme for an authentic appearance. It is powered by an efficient 16V brushless motor and includes quick-release rotor blades for user-friendly assembly.

Figure 1: FLYWING MH-60R Seahawk Scale RC Helicopter.
Video 1: Overview of the MH-60 helicopter models, showcasing flight and features.
2. Safety Information
2.1. Reading Tips and Symbols
- ⚠️ IMPORTANT: Indicates critical information for safe operation.
- 💡 INSTRUCTIONS FOR OPERATION AND USE: Provides guidance on product usage.
It is recommended that the user first watch the instructional video and read this User's Manual to understand the detailed use process and flight safety-related contents of the product. The product should then be used safely in a compliant location.
2.2. Flight Safety Guidelines
Pre-Take-off Inspection
- Installation and component inspection:
- Each module is installed correctly and firmly.
- The wiring of the electric regulator and receiver is correct and firm.
- Inspection of working condition:
- Verify the mode switch corresponds to the LED status indicator flashing.
- Check whether the working status indicator of GNSS-Compass flashes correctly.
- Check whether the sensor parameters are normal and calibrate according to the prompt.
- Shake the helicopter before takeoff to check that it is always level and correct.
Safety Summary
Users are strongly encouraged to enjoy flying in a safe and reasonable environment. Necessary knowledge of flight safety is important for your safety and the safety of people and the environment. Ensure you have sufficient knowledge of the helicopter and all emergency operations.
Environment
- Fly in open spaces away from people, traffic roads, ground facilities, airports, other aircraft, or obstacles.
- Flight altitude is limited by aircraft performance. High-altitude conditions may reduce battery and powertrain efficiency. Understand your aircraft's capabilities and fly cautiously.
- The flight control system operates within an ambient temperature range of -10°C to 55°C (non-direct sunlight conditions).
- Fly only in favorable weather (no rain, strong winds, or extreme conditions), during daylight or under well-lit conditions.
- Fly within legally permitted zones.
Inspection
- Ensure all devices are fully charged.
- Ensure that the propeller is not damaged and installed securely.
- Ensure that the helicopter components are clean and undamaged.
- Ensure that all modules of the flight control system are installed firmly and do not directly contact other metals and conductive materials. The installation position and orientation must be correct, connections normal and firm, plugs free of looseness, and wires not pulled by force.
Operation
- Do not get close to the rotating propeller and motor.
- Fly within the visual range of the unaided eye.
- Do not transport dangerous and prohibited goods.
- Turning the CH7 motor control switch during flight will cause the helicopter to crash. Use this function only in an emergency.
- Do not make or receive phone calls or text messages during flight, and do not operate the helicopter under the influence of alcohol or drugs.
- Please return as soon as possible in case of low battery (or low voltage) warning.
- When the helicopter automatically returns, it will not avoid obstacles by itself. If the remote control signal is normal, the helicopter can cancel the return flight through the remote controller.
- After landing, close the helicopter first and then turn off the remote controller to avoid loss of the remote controller signal and starting the return mode.
- It is forbidden to use this product to throw or emit any dangerous articles to buildings, people, or animals.
2.3. Disclaimer and Warning
⚠️ This product is not a toy and is not suitable for use by persons under the age of 18. Do not allow children to come into contact with this product and take special care when operating in the presence of children.
Read this document carefully before using this product. This statement has an important impact on the safe use of this product and your legal rights.
This product is a helicopter flight control system, which will provide safe and reliable flight control under the condition that the power supply works normally and all components are not damaged. Visit http://www.flywingrc.com for the latest instructions and warnings. Flywing reserves the right to update this disclaimer. Please refer to the version received at www.flywingrc.com for the latest disclaimer.
By using this product, you are deemed to have understood, acknowledged, and accepted all terms and contents of this statement. The user undertakes to be responsible for their own actions and all consequences arising therefrom. The user undertakes to use this product only for proper purposes and agrees to these terms and any relevant policies or guidelines that Flywing may have.
To the maximum extent permitted by law, in no event shall Flywing be liable for any indirect, consequential, punitive, incidental, special, or punitive damages, including damages arising out of your purchase, use, or inability to use this product, even if Flywing has been advised of the possibility of such damages.
Compliance Statement
- Disclaimer: ⚠️️ Not suitable for children under 36 months.
3. Setup
3.1. Prepare the Helicopter Battery
The flight battery needs to be charged for the first time. Connect the supplied charger to the battery plug, turn the charger mode switch to 'Charge' mode, and connect to AC power to start charging. When '99' is displayed on the screen, the battery is fully charged.
Note: If the battery is not used for more than 5 days, it is recommended to use the storage mode of the charger to save the battery, and check the operation once every month.

Figure 2: Battery charger and battery for the helicopter.
3.2. Preparing the Remote Control
To use the remote controller for the first time, open the battery compartment cover on the back of the remote controller, prepare 4 AA batteries (not included), move all the toggle switches to the uppermost side, and press and hold the two power buttons for 5 seconds to complete the startup.

Figure 3: High-Precision 10-Channel Transmitter layout.
Controller Mode (Mode2 Example - Left-Hand Throttle)
| Left Stick | Right Stick |
|---|---|
| Up: Throttle Up | Up: Forward |
| Down: Throttle Down | Down: Backward |
| Left: Yaw Left | Left: Roll Left |
| Right: Yaw Right | Right: Roll Right |
3.3. Insert Blades
Insert the blade with its sharp edge facing up into the rotor holder; rotate the blade 90° clockwise, then pull it outward to confirm the spring snaps back.

Figure 4: New 4-blade rotor head with user-friendly QR propeller blade design for simpler installation.
3.4. Powering Up the Helicopter
After switching on the transmitter, pull down the latch to open the front canopy. Secure the battery to the wooden base plate inside. Plug the yellow XT60 battery connector into the ESC to power the helicopter. Close the canopy, set the model on the ground, and keep it motionless while the servos move to complete the self-test.
3.5. Compass Calibration
Please select an open area and follow the steps below to calibrate the magnetometer. For additional guidance on compass calibration, visit the official website www.flywingrc.com to watch video tutorials.
Method 1: Calibration with Remote Control
- Put the flight mode switch of the remote controller in the Home mode, then quickly dial to the ATT mode, and then dial back to the Home mode, repeat above 3 times, and finally stay in the Home mode. Wait a few seconds and the GPS light begins to flash red and enter the magnetometer calibration state.
- Roll each face of the helicopter for at least 2 circles; the status light of the flight control will gradually change from red to green. Finally, when the flight control light is normally on and then off, the calibration is completed, and the flight control will restart automatically. When restarting, the LED lights flash red quickly, then turn off for a few seconds, and finally flash red and blue quickly, and the restart is completed.
Flight control LED: red-green flash → yellow flash → blue flash → green flash → steady green → automatic restart
External LED: red light is always on → orange light is always on → yellow light is always on → green light is always on → automatic restart
During the restart, the helicopter must be placed on the ground and held still, waiting for flight control self-test (do not hold the helicopter in hand).

Figure 5: LED indicators during compass calibration (Red, Yellow, Green lights).
4. Operation
4.1. Outdoor Flight
Set the remote controller to GPS mode, place the helicopter in an open area, and wait for satellite lock. When the green light stays solid, grasp the helicopter and rotate it 360° horizontally; watch whether the LED turns yellow or red. If the compass is normal (green light solid), you can take off (wait one minute after the green light appears so the home point refreshes more accurately). If the LED flashes yellow or red at any angle, recalibrate the compass. Next, move the sticks to check that the servos travel correctly and that the mechanics are free of binding or damage. When everything is verified, you are ready to lift off.
4.2. Take-off
Ensure that the remote controller is in GPS mode and the helicopter is in an open field. Observe the flight environment. After confirming that it is normal, the flight control is unlocked and the green light flashes. During the flashing period, turn the start/stop switch to the start position, and the helicopter begins to accelerate slowly. Wait for about 10 seconds until the helicopter speed is stable, push the ascending and descending rocker for 1 second, and then the helicopter takes off. Release the rocker to hover the helicopter.

Figure 6: MH-60R performing a soft take-off from a landing pad.
4.3. Landing
Ensure the helicopter is above an open area. Survey the flight environment and confirm normal conditions. Gradually pull the throttle stick downward without engaging the lowest position—the helicopter will descend slowly until it touches the ground. After a stable and steady landing, toggle the engine start/stop switch to the cut-off position, then gently release all control sticks and wait for the rotors to come to a complete stop.
4.4. One-Key Return (RTH)
Ensure that the helicopter is above an open field. After confirming normal flight environment, turn the return switch to 'return'. All indicator lights of the flight control will turn purple and remain on. The helicopter will select different return modes based on its distance from the take-off point:
- Within 10m from the current position to the return point:
- If front altitude is less than 5m, it will rise to 5m and return.
- If current altitude is greater than or equal to 5m, it will return at the current altitude.
- More than 10 meters from the return point:
- If front altitude is less than 15m, it will return to the altitude of 15m.
- If current altitude is greater than or equal to 15m, it will return at the current altitude.
Note: The return point is the position where the helicopter unlocks the take-off position. The accuracy depends on GPS satellite quality during takeoff. It is recommended to wait one minute after the flight control green light is normally on before takeoff to allow the satellite signal to stabilize. During RTH, the remote controller cannot operate the helicopter, but fine adjustments can be made during landing.

Figure 7: Multi-layer Safety Protection including One-Key/Low-Battery RTH.
4.5. Low Battery Return
The MH-60 ACE supports 4S Li-Po battery and has a built-in two-stage voltage protection mechanism. When the battery power is low, the helicopter automatically triggers low battery protection, alarms, and initiates RTH after a few seconds. The return mode is similar to One-Key Return.
- When the battery voltage is lower than 15.2V, it is forbidden to unlock the helicopter.
- When the battery voltage is less than 14.77V, the helicopter triggers a level I charge alarm (all indicator lights flash slowly in purple).
- When the battery voltage is lower than 14.73V, the helicopter triggers the primary power return (all helicopter indicators are solid purple). The user can cancel this return by switching the return voltage switch.
- When the battery voltage is less than 14.6V, the helicopter triggers a secondary battery alarm (all lights flash purple).
- When the battery voltage is lower than 14.53V, the helicopter triggers a secondary power return and forces a second return. At this point, the user cannot cancel until the helicopter returns and lands.
4.6. Coordinated Turn
When the C-Turn function is enabled, using the YAW stick for turning will automatically increase the aileron roll control based on the current flight speed. This helps the helicopter turn with a smaller radius and achieve a more realistic turning posture. This function is valid by default in GPS mode and ATT mode.

Figure 8: MH-60R performing a coordinated turn for realistic flight.
4.7. Three Flight Characteristics Modes
The helicopter has built-in three flight sensitivities, which can be switched via the remote control switch:
- Soft Mode: Maximum flight speed, flight angle, and reaction speed are limited. Ideal for novices.
- Normal Mode: Faster than soft mode in speed, angle, and reaction. Suitable for daily helicopter flight.
- Sport Mode: Maximum flight speed, flight angle, and reaction speed reach maximum control values. The helicopter is very flexible and fast. Recommended for experienced players in open fields.

Figure 9: Visual representation of Soft, Standard, and Sport flight modes.
4.8. Soft Take-off/Land
When the helicopter takes off and lands, the flight control takes over the vertical velocity completely. When the altitude reaches 1m, it switches to proportional control of the remote controller. This feature helps prevent the helicopter from taking off too fast. During take-off, only the throttle lever affects vertical movement; other directional controls remain active. (Note: Distance estimation by barometric pressure may have some error in windy weather.)
5. Maintenance
- Check the status of each module of the flight control system regularly.
- The flight control system is suitable for long-term storage in a dry environment of 5°C to 35°C, with no heat source nearby, no vibration, no strong magnetic field, and no strong electric field.
- Do not store in a high place to avoid accidental drop, which may cause damage to the equipment or abnormal operation.
6. Troubleshooting
This section provides guidance for common issues you might encounter. For more complex problems, please refer to the official website or contact support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Helicopter does not power on | Battery not charged, loose connection, faulty battery/ESC. | Ensure flight battery is fully charged. Check all power connections (XT60). Test with a different battery if available. |
| Unstable flight/Drifting | Improper compass calibration, weak GPS signal, windy conditions, damaged blades. | Perform compass calibration in an open area. Wait for strong GPS lock. Fly in calm weather. Inspect blades for damage and replace if necessary. |
| Loss of control signal | Out of range, interference, low remote control battery. | Ensure you are within the 1KM communication range. Avoid areas with strong electromagnetic interference. Replace AA batteries in the remote control. |
| Helicopter not responding to remote | Remote control not powered on, not paired, low remote control battery. | Ensure remote control is powered on and has fresh batteries. Re-pair the remote control with the helicopter if necessary (refer to remote control manual). |
| RTH not working as expected | Poor GPS signal at takeoff, obstacles in return path. | Ensure strong GPS lock before takeoff. Fly in open areas free of obstacles. RTH does not avoid obstacles automatically. |
7. Specifications
| Feature | Detail |
|---|---|
| Brand Name | F FLY WING |
| Model Number | MH-60R |
| Type | HELICOPTER |
| Material | Metal, Plastic, Fiberglass |
| Drone Weight | 1328g |
| Takeoff Weight | 1.5kg |
| Dimensions | 85X25X27CM |
| Remote Distance | 800M |
| Flight Time | 10~20 minutes (up to 18 minutes) |
| Control Channels | 6 channels |
| Controller Battery | AA (Not included) |
| Is Batteries Included | Yes (Flight battery) |
| Motor Type | Brushless Motor |
| Plugs Type | US EU AU UK (option) |
| State of Assembly | Almost Ready |
| Remote Control | Yes |
| Aerial Photography | No |
| Operator Skill Level | Beginner, Intermediate, Expert |
| Indoor/Outdoor Use | Outdoor |
| Controller Mode | MODE1, MODE2 |
| Recommend Age | 14+y |
| Anti-wind Ability | 3 class |
| Features | App-Controlled, ATT Self-leveling Mode, Coordinated Turn for More Realistic Flight, Smooth Takeoff and Landing, One-Touch/Low-Battery RTH, Three adjustable flight modes, Efficient gear configuration with 3508 brushless motor, Stable hovering (±1.5m horizontal, ±0.5m vertical with GPS), Quick disassembly blade, High-realistic details, LED indicator light |
| Package Includes | Original Box, Batteries (flight), Operating Instructions, Charger, Remote Controller, USB Cable |
8. User Tips
- Inspect Upon Arrival: Carefully check the product and packaging for any damage immediately upon receipt. If any defects or damage are found, contact the seller directly for prompt assistance.
- Accessory Availability: If you are looking for specific accessories like side mounts, check the product options or contact the seller for availability.
- Battery Storage: For optimal battery life, if the flight battery is not used for more than 5 days, utilize the charger's storage mode and check its operation monthly.
- Compass Calibration: Always perform compass calibration in an open area, free from magnetic interference, and ensure a strong GPS lock before flight for stable performance.
9. Warranty and Support
9.1. Warranty Information
The product comes with a 3-month warranty covering non-human-caused damage. Please retain your proof of purchase for warranty claims.
9.2. Further Support and Documentation
For the latest user manual, video tutorials, and additional support, please visit the official FLYWING website:
A PDF version of the user manual is also available for download. You can access it directly via this link: User Manual (PDF).
If you have any suggestions or require further assistance, you can leave a message on the official website.
10. Accessory Information Table
Below is a list of accessories and their corresponding part numbers for the MH-60R helicopter.

Figure 10: Custom NACA 8-H-12 flat convex prop design.

Figure 11: The all-new ACE flight controller for effortless flying.

Figure 12: High-performance coreless metal gear servo details.
| Part Number | Description |
|---|---|
| FS08 | Main Shaft |
| FS14 | Aluminum Column |
| FS95 | Quick 4 Blade Rotor |
| FS28 | Main Motor |
| FS29 | Main Gear Fixed Plate |
| FS57 | Long DFC Pitch Linkage |
| FS52 | 4 Blade Swashplate Set |
| FS33 | Main Shaft Mount |
| FS34 | Side Frame Plate |
| FS35 | Bottom Plate |
| FS36 | Anti Rotation Bracket |
| FS37 | Controller Installed Plate |
| FS39 | 60A Scale ESC |
| FL446 | H041 Servo |
| FS41 | Tail Motor |
| FS43 | M10 GPS |
| FS72 | Rotor Holder |
| FS53 | Rotor Hub Cap |
| FS89 | Main Rotor Housing |
| FS90 | Feather Shaft |
| FL453 | Main Shaft Fixed |
| FV305 | Main Gear |
| FV315 | Tail Blade |
| FV319 | Motor Gear |
| FL413 | Swashplate Linkage Rod Set |
| FL443 | H041 Servo Arm |