1. Important Notes
- Keep this user manual in a safe place. Always include it when lending the product to others.
- Follow all warnings and instructions in this manual.
- Do not disassemble or damage the product. Stop using it immediately if it is deformed or damaged.
- Store the product in a dry, well-ventilated area.
- Keep the product out of reach of children.
- The product has passed IP68 ingress protection testing. Do not use it in extreme water environments, unknown liquids, hot springs, or corrosive fluids.
- Compatible only with 7-inch or smaller straight smartphones.
- Do not install the product over a phone case.
- Waterproof depth rating: 20 meters (65 feet).
2. Product Overview
The TELESIN Diving Phone Remote Case is designed for underwater smartphone photography, offering robust protection and intuitive controls.
2.1. Components and Controls



2.2. What's in the Box

- Diving handle × 1
- Vacuum pump × 1
- USB charging cable × 1
- Safety hand strap × 1
- Lens Cloth × 1
- Manual × 1
3. Setup and Installation
3.1. Watertight Safety Test (Before First Use)
It is strongly recommended to perform a watertight safety test before the first use and after any significant impact or maintenance.
- Place a tissue inside the case.
- Seal both the case and the vacuum cover tightly.
- Fully submerge the case in water for 30+ minutes.
- Do not open immediately after retrieval.
- Check if the tissue remains dry:
- If dry: waterproof integrity verified.
- If wet: contact official support.
3.2. Bluetooth Pairing
- Power on the diving handle by long-pressing the Capture Button for 2 seconds. The indicator light will flash, entering Bluetooth pairing mode.
- On your phone, go to Bluetooth settings and connect to "TELESIN SDC".
Note: The device will auto-shutdown after 2 minutes if unpaired.
3.3. iOS Initial Setup (One-Time Only)
For full button functionality on iOS devices, you need to enable Zoom accessibility:
- Go to Settings → Accessibility → Zoom.
- Enable Zoom.
- Set Zoom Region to Full Screen Zoom.
Note: Screen magnifies when enabled. Triple-tap with two fingers to reset. Other settings unchanged. Android devices skip this step.
3.4. Phone Settings for Optimal Use
- Disable Auto-Lock: Go to Settings → Display & Brightness → Auto-Lock (or Screen Timeout) → Set to "Never".
- Enable Do Not Disturb Mode: Activate Do Not Disturb mode to prevent notifications/interruptions during camera operation.
- Launch the Default Camera App to start capturing photos/videos.
3.5. Phone Installation Procedure
- Before inserting the phone, use a cleaning cloth to wipe the lens, the inner glass surface of the Diving House, and the transparent interior.
- Unlock all 5 latches and open the cover.
- Remove your phone's case and install the bare device.
- Align the phone lens with the viewport. Ensure the phone is flushed against the left edge and secure in the clamp. If the camera lens is blocked, adjust the phone's position slightly to the right.
- Close the cover and lock all 5 latches securely.
- Unscrew the vacuum port (counterclockwise).
- Press the rubber head of the vacuum pump firmly onto the port. Pump 3-4 times to prevent air condensation and eliminate lens/screen fogging.
- Tighten the vacuum port (clockwise).
3.6. Attach Safety Leash
Attach the safety leash to the designated loop on the case. This is essential for freediving/scuba when hands-free operation is needed (e.g., for ear equalization or hand signals).
4. Operating Instructions
4.1. Power On/Off
- Power On: Long press the Capture Button for 2 seconds. The indicator light will flash, entering Bluetooth pairing mode.
- Power Off: In on or sleep mode, long press the Capture Button for 2 seconds. The indicator light will flash quickly three times and then go out, turning off the remote control.
4.2. Sleep Mode
- Entering Sleep Mode: The device will auto-sleep after 60 minutes of inactivity post-pairing. If disconnected via phone settings, distance, or Bluetooth off, it will enter sleep mode and auto-off after 30 minutes.
- Waking from Sleep Mode: Press any button to wake up. It will auto-reconnect if the last paired phone's Bluetooth is on. If the previously paired phone's Bluetooth is off and there's no pairing within 2 minutes, the device will enter sleep mode and shut down after 30 minutes.
4.3. Button Functions
- Capture Button: Single press to start/stop recording.
- Mode Button 1: Single press to switch between shooting modes. Long press (2s) for quick camera access from lock screen.
- Mode Button 2: Single press to switch between shooting modes. Long press (2s) to switch between front and rear cameras.
- Zoom Button (W): Zoom out (wide-angle).
- Zoom Button (T): Zoom in (telephoto).
5. Maintenance
5.1. After Using in Seawater
- Remove the phone, ensure the product is securely closed, and submerge it in clean water (freshwater) for 10 minutes.
- Remove the product from the freshwater and rinse it under gentle running tap water for 5 minutes.
- Dry the product with a towel after rinsing. Do not use a hairdryer or heater for drying.
- The interior of the product is not waterproof. Do not rinse the interior; otherwise, the circuit will be damaged.
5.2. Removing the Phone After Use
First, unscrew the vacuum cover, press the black gasket to release pressure, and then unlock the sealing buckles after deflating. Otherwise, it will be unable to open due to excessive adsorption from negative pressure.
6. Charging
Use the included charging cable for charging. Connect the contact point end to the charging port on the left side of the diving house, and connect the other end of the charging cable to a USB power source.

- Do not cover the product with towels, clothing, or similar items during charging to prevent fire hazards.
7. Specifications
| Parameter | Value |
|---|---|
| Product Model | P4-WTP-06 |
| Material | ABS+PC+Aluminum Alloy |
| Product Size | 203.66mm × 109.18mm × 52mm |
| Product Weight | 397g |
| Charging Time | 2 hours |
| Battery Capacity | 80 mAh |
| Input | Pogo Pin Connector, 5V ⎓ 0.5A |
| Battery Nominal Voltage | 3.7V |
| Bluetooth Compatible Devices | Apple (iOS), Android, and HarmonyOS smartphones (7-inch or smaller screens) |
*Data measured by Telesin laboratory, slight deviations may occur due to changes in objective conditions.
8. Troubleshooting
- Fogging inside the case: Ensure the vacuum pump procedure (Section 3.5, step 7) is performed correctly to remove air and prevent condensation. Always ensure your phone and hands are dry during installation.
- Buttons not working on iOS: Verify that the iOS Initial Setup (Section 3.3) for Zoom accessibility is completed.
- Bluetooth connection issues: Ensure the device is powered on and in pairing mode. Check your phone's Bluetooth settings. If the device auto-shutdowns after 2 minutes, power it on again.
- Phone not fitting: This case is compatible with straight smartphones 7-inch or smaller. Remove any phone cases before installation.
- Water ingress during test: If the tissue inside gets wet during the watertight safety test, do not use the product and contact official support immediately.
9. User Tips
- Always perform the watertight safety test before each dive, especially after any maintenance or if the case has been stored for a long time.
- For best results, always install your smartphone without its protective case.
- Remember to enable 'Do Not Disturb' mode on your phone to avoid interruptions from notifications while shooting underwater.
- Utilize the safety leash to secure the case to your wrist, preventing accidental drops, especially in strong currents or during hands-free tasks.
- If you experience any issues with button functionality on iOS, double-check your Accessibility settings for Zoom.
10. Warranty and Support
10.1. Disclaimer
Please read this statement carefully. By using this product, you acknowledge and accept it in full. Before each use, carefully check the product. Do not use it if damaged or deformed. By using this product, you are fully responsible for your actions and the possible consequences. You agree to use this product only for legitimate and lawful purposes. TELESIN shall not be liable for any misuse, adverse effects, damages, injuries, penalties, or other legal consequences arising directly or indirectly from the use of this product. Users should follow all precautions mentioned herein. TELESIN reserves the right to interpret and modify this commitment within the limits of national laws and regulations.
10.2. Warranty Period
The warranty period for TELESIN products begins 6 months from the day you receive the product.
10.3. FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. *RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure conditions without restriction.
10.4. IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF exposure statement: The device was evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction.