Introduction
Thank you for purchasing the XIMA Android Car Media Player. This manual provides detailed instructions for the installation, operation, and troubleshooting of your new car radio. Please read this manual thoroughly before use to ensure proper functionality and to avoid any issues.
Important: Before proceeding with a full installation in your car, it is highly recommended to test the unit first. Products can be affected by long journeys, and a preliminary test can help identify any issues before permanent installation.

Overview of the XIMA Android Car Radio, highlighting key features like screen sizes (7", 8", 9"), fan cooling, wireless CarPlay/Android Auto, Android 15 OS, 4GB RAM + 64GB storage, ASP-DSP audio processing, and 1280x720 QLED screen resolution.
Setup and Installation
Pre-Installation Check
Before purchasing and installing, you must confirm the original car system configuration, year, and central control map of your vehicle model to avoid installation incompatibility.

Important note for pre-purchase compatibility. Displays examples of car dashboards where the unit can be installed (green check) and where it cannot (red cross), based on the original car system configuration.
Package Contents
Please verify that all items are present in your package:
- 1 XIMA Android Car Media Player (7", 8", or 9" screen)
- 1 Power Cable for VW
- 1 CANBUS Decoder
- 1 RCA Input/Output Jack
- 1 Rear Camera Input Cable
- 2 USB Data Cables
- 1 GPS Antenna
- 1 External Microphone (Gift)
- 1 Fan
- 2 Universal Car Mounts
- 4 Screws
- 1 User Manual

Visual representation of all items included in the package: the main head unit (9-inch shown), external microphone, power cable, RCA and microphone jack, camera input cable, two USB data cables, GPS antenna, and CAN BUS decoder.
Rear Interface Description (Power Plug)
The power plug connects to your car's electrical system. Ensure correct wiring to prevent damage and ensure proper operation.
| Wire Color | Function |
|---|---|
| Yellow (B+) | Constant Power Supply +12V (Memory Function) |
| Red (ACC) | Ignition Switch (Switched +12V) |
| Black (GND) | Ground Wire |
| Orange (ILLUMINATION) | Illuminate Backlight |
| Pink (REVERSE) | Reversing Camera Control Line |
| Brown (KEY2) | Steering Wheel Control -2- |
| Orange/black striped (KEY1) | Steering Wheel Control -1- |
| Blue (ANT) | Auto Antenna Power |
| White / White/black striped | Front Speaker (L) |
| Gray / Gray/black striped | Front Speaker (R) |
| Green / Green/black striped | Rear Speaker (L) |
| Purple / Purple/black striped | Rear Speaker (R) |
Notes on Power and Speakers:
- The unit turns on normally when both the Yellow (B+) and Red (ACC) lines receive 12V positive power simultaneously.
- The Yellow (B+) line maintains power for the machine's memory function.
- There are 8 speaker cables. Each cable must not be grounded, shared, or touch other lines. Incorrect wiring can lead to no sound output, distorted sound, or overheating.
CANBUS Connection
The CANBUS connection varies depending on your car model. Refer to the diagrams below for high-end and low-end models.

Detailed wiring diagrams for 36-pin and 40-pin connectors, and step-by-step solutions for diagnosing and resolving power-related problems.
Attention: If the CANBUS box and black buckle are connected simultaneously, it may cause the radio to fail to shut down after the car is turned off.
Reversing Camera Installation
Follow the diagram to correctly connect your reversing camera. The camera input cable is typically pink (REVERSE) and connects to the reverse light's positive pole.

Displays the view from an AHD HD camera, emphasizing features like waterproofing, high-temperature resistance, and 1920x1080 resolution (optional).
Important: If a reversing camera is not installed, do not connect the REVERSE/BACK cable. Leave it unconnected. Otherwise, the unit may not display correctly or could automatically enter reverse mode, leading to malfunction.
Operation
Learning Steering Wheel Controls
You can map functions to your car's existing steering wheel buttons:
- Press and hold a button on your original car's steering wheel.
- On the car radio screen, find the corresponding button icon for the function you want to assign.
- Click the icon to change its color. Successful learning is indicated by the color change.

Demonstrates the customizable settings, including audio controls and the ability to map functions to existing steering wheel buttons.
Apple CarPlay (Wireless & Wired)
The unit supports both wired and wireless Apple CarPlay functionality.
- Wired Connection: Simply connect your iPhone to the unit using a USB data cable. The CarPlay interface will launch automatically.
- Wireless Connection:
- Enable Bluetooth and Wi-Fi on your iPhone.
- Connect your iPhone to the car radio via Bluetooth.
- The CarPlay interface will launch automatically. The signal is transmitted via Wi-Fi, so CarPlay will function even if Bluetooth is turned off. If Wi-Fi is turned off, CarPlay will disconnect.
Android Auto (Wireless & Wired)
The unit supports both wired and wireless Android Auto functionality. This feature may require local availability of Google Play services.
- Ensure you have the "Android Auto" app installed from Google Play.
- Use an Android phone with OS 6.0 or higher and a valid USB data cable.
- Wired Connection: Connect your Android phone to the unit using a USB data cable. The Android Auto interface will launch automatically.
- Wireless Connection:
- Enable Bluetooth and Wi-Fi on your Android phone.
- Connect your Android phone to the car radio via Bluetooth.
- The Android Auto interface will launch automatically. The signal is transmitted via Wi-Fi, so Android Auto will function even if Bluetooth is turned off. If Wi-Fi is turned off, Android Auto will disconnect.

Explains the built-in CarPlay and Android Auto functionalities, supporting both wireless and wired connections (Bluetooth/USB). Shows example interfaces for iOS and Android phones.
Bluetooth Functionality
The unit features an independent Bluetooth module for hands-free calling and audio streaming.
- Turn on the car radio and enable Bluetooth on your mobile phone.
- Search for the car radio's Bluetooth name on your phone and connect.
- Once connected, you can answer calls and play music through the car radio.

Highlights the independent Bluetooth module, showing the interface for making calls and accessing the address book.
Split Screen Mode
The unit supports application split-screen, allowing you to run two applications simultaneously, such as navigation and a media player.

Illustrates the application split-screen feature, allowing simultaneous display of navigation (e.g., Google Maps) and media playback.
Troubleshooting
This section addresses common problems and provides simple solutions. If issues persist, please contact customer support.
1. Cannot Boot Normally
- Wiring Check: Ensure the Yellow (B+), Red (ACC), and Black (GND) wires are correctly connected to positive, key control, and negative poles respectively. Incorrect or insufficient connections will prevent booting.
- Original Car Line Compatibility: The original car wiring may not match the unit's standard color coding. Connecting incorrectly can cause damage.
- Fuse Check: If the unit doesn't boot despite correct wiring, check the fuse on the yellow line. If the fuse is intact, twist the yellow and red wires together, turn the key, and press the power button to test.
- Direct Power Test: If all else fails, connect the yellow and red wires directly to a 12V positive power source and the black wire to negative. If the unit boots, the issue is with your car's wiring; otherwise, the unit may be faulty.
2. Automatic Shut-down
- Cable Connection Error: If the blue (automatic antenna power supply) cable is connected to the unit's power cable, automatic shutdown will occur. Correct the wiring.
- Unstable Voltage: Test with a stable 12V-5A power supply. If the unit still shuts down, it's a unit problem. If not, replace your car's power supply.
3. There is Noise
- Speaker Power: If the original speaker power is too low, noise will occur at high volumes. Avoid excessively high volume.
- Grounded Speaker Cable: If a speaker cable is grounded, connect the iron speaker cable directly to the unit's speaker cable.
4. Remote Control Cannot Be Used
- Test Method: Use your phone camera to view the remote control's light while pressing buttons. If no light, replace the battery. If it lights up, the remote control is functional.
5. Settings Cannot Be Saved (No Memory)
- Ensure the yellow and red lines are connected correctly (yellow to positive, red to key control).
- If yellow and red are reversed, simply swap their positions.
6. Bluetooth Not Working
- Turn on the unit, search for its Bluetooth name on your mobile phone, and click Connect.
7. The Product Emits Smoke
- Replace the FUSE. If the problem persists, the internal circuit is burned, requiring after-sales service.
8. The Sound Cannot Be Adjusted
- Reset the unit or unplug and replug the power cord.
- If the volume knob is broken, it can be replaced.
9. Reversing Camera Does Not Display
- Wrong/Missing Wiring: Ensure all camera accessories (camera, power cord, video cable) are correctly connected.
- Broken Camera: If the camera's lamp doesn't light up when properly wired, the camera is likely broken and needs replacement.
10. USB Devices Cannot Be Played
- Format the USB flash drive to FAT32. Re-download songs and try again. If it still doesn't work, replace the USB drive.
11. FM Does Not Receive Radio Stations
- Antenna Connection: Ensure the antenna plug is fully inserted and the antenna is not disconnected.
- Search Station: Use the "AS" button for automatic search or the "before/after" buttons for manual tuning.
- If issues persist, unplug the antenna plug and try inserting a screwdriver or metal strip into the antenna port as a temporary antenna.
12. No Sound Right After Installation
- This is usually due to a wiring error or a short-circuited original car speaker wire.
- Check Speaker Cables: Verify that speaker cables are not short-circuited or incorrectly connected. Reconnect if necessary.
- Speaker Cable Count: If your original car has only 2 speaker cables, but the unit requires 4, you may need to re-route the original car line. Each speaker needs 2 cables.
13. No Sound After A While
- Disconnect all speaker cables from the unit (do not remove them). Connect an external speaker to the gray and purple wires of the unit's tail line. Connect any green wire, then test for sound.
- If there is sound, the car's speaker line is short-circuited or the speaker is damaged. If there is no sound, the unit is broken.
Specifications
| Feature | Specification |
|---|---|
| Brand Name | XIMA |
| Operating System | Android 15 (CAR ADNROID) |
| RAM | 6G |
| ROM | 64G |
| Display Size | 7", 8", 9" |
| Resolution | QLED Screen |
| Built-in Screen | Yes |
| Din | Double Din |
| Interface | Volkswagen ISO |
| Out Power | 50W * 4 |
| Voltage | 12 V |
| Item Weight | 1.3kg |
| Item Size | 220*130*210mm |
| Max External Memory | 128G |
| Material | ABS+ |
| Certification | CE |
| Origin | Mainland China |
| Applicable Models | For VW/Volkswagen/Passat/GOLF/Skoda, B6 Jetta Polo Tiguan, Golf 5 6 Touran Passat |
| Special Features | Wi-Fi function, Support 4G Network, Support Can-Bus, Built-in GPS, Charger, Mobile Phone, MP3 players, Remote Controller Included, Support steering wheel control, Mirror link, Carplay, Android Auto, DAB+ (Optional) |
| Digital Media Format | CD, DVD-R/RW, DVD-RAM, VIDEO CD, Mp3, MP4, WMA, JPEG |
| OSD Language | Multi-language support including English, Spanish, Russian, German, French, Italian, etc. |
Package Dimensions
- Length: 28 cm
- Width: 19 cm
- Height: 14 cm
- Weight: 1.4 kg
User Tips
- Initial Test: Always perform a bench test of the unit before full installation to ensure it powers on and functions correctly after transit.
- Wiring Verification: Double-check all wiring connections, especially power and speaker cables, against the provided diagrams to prevent short circuits or malfunctions.
- CANBUS Caution: If your vehicle uses a CANBUS system, ensure the CANBUS box is correctly integrated and avoid simultaneous connection with the black buckle if it causes power-off issues.
- Software Updates: Keep your unit's software updated to ensure optimal performance and access to the latest features. Check the manufacturer's website or settings for updates.
- USB Compatibility: For USB devices, ensure they are formatted to FAT32 for best compatibility.
- Steering Wheel Control Setup: Take your time to correctly map your steering wheel controls for a safer and more convenient driving experience.
Warranty and Support
Warranty
This product comes with a 1-year warranty from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty covers manufacturing defects but does not cover damage caused by improper installation, misuse, or accidents.
Further Assistance
For a more detailed user manual, you can refer to the official PDF document: User Manual (PDF)
If you require further assistance or have questions not covered in this manual, please contact our customer service team through the following channels:
- WhatsApp: Scan the QR code for Engine WhatsApp support.
- TikTok: Scan the QR code for TikTok support.
- Instagram: Scan the QR code for @LEHXCARRADIO on Instagram.



Scan the QR codes for direct support via WhatsApp, TikTok, and Instagram.