LUMDEER HT-068

Contents

LUMDEER Road Bicycle Helmet User Manual

Model: HT-068

Brand: LUMDEER

1. Introduction

Thank you for choosing the LUMDEER Road Bicycle Helmet, Model HT-068. This helmet is designed to provide optimal protection and comfort for road cycling and other compatible sports. It features a lightweight design, advanced ventilation, and integrated safety features to enhance your riding experience.

This product complies with the essential health and safety requirements set out in Regulation (EU) 2016/425 Personal Protective Equipment and meets the requirements of Harmonized Standards EN 1078:2012+A1:2012 and CPSC 16 CFR Part 1203.

Cyclist wearing a LUMDEER helmet with an illuminated magnetic taillight.
Figure 1: LUMDEER Road Bicycle Helmet with Magnetic Taillight.

2. Safety Instructions

WARNING: No helmet can prevent all head injuries. Even in low-speed accidents, serious injury or death can occur. For best protection, the helmet must be fitted and attached properly to the head in accordance with the fitting instructions. Destroy and replace the helmet after impact. Protection may not be adequate in future impacts as damage can be invisible.

  • The helmet can only protect if it fits well. Always try different sizes to ensure a secure and comfortable fit.
  • Adjust the straps so they do not cover the ears. The buckle should be positioned away from the jawbone.
  • Ensure straps and buckle are adjusted to be both comfortable and firm.
  • Position the helmet on your head to protect the forehead and prevent it from being pushed too far over the back of the head.
  • A helmet subjected to a severe impact should be immediately discarded and destroyed, even if visible damage is not apparent.
  • Do not modify or remove any original component parts of the helmet.
  • Do not adapt the helmet for fitting accessories in a way not recommended by the manufacturer.
  • This helmet should not be used by children while climbing or doing other activities where there is a risk of strangulation/hanging if the child gets strapped with the helmet.
  • Do not clean with solvents, bleaches, or strong detergents, as these can damage the helmet, sometimes invisibly.
  • If you are unable to adjust the size of the helmet so that it can only be moved slightly forward or backward with the straps closed, do not use it. Exchange the helmet for a smaller or different model.

3. Setup & Adjustment

Proper fit and adjustment are crucial for the helmet's protective effectiveness.

3.1 Initial Fit Check

  1. Place the helmet squarely on your head, ensuring it covers your forehead.
  2. Adjust the internal fitting system (knob adjustment) until the helmet feels snug and secure without excessive pressure.
  3. Shake your head gently. The helmet should not move significantly.
Rear view of helmet showing the knob adjustment system for head circumference.
Figure 2: Knob Adjustment System. Sizes M (52-56cm) and L (57-62cm) are available.

3.2 Strap and Buckle Adjustment

  1. Webbing System: Adjust the side straps so that they form a "Y" shape just below your ears. Ensure the straps lie flat against your head and do not twist.
  2. Buckle: Fasten the magnetic lock buckle. Position the buckle away from your jawbone.
  3. Chin Strap: Tighten the chin strap until it is snug under your chin. You should be able to open your mouth wide, but the helmet should not move forward or backward more than an inch.
Close-up of the advanced magnetic lock buckle for quick and easy fastening.
Figure 3: Advanced Magnetic Lock Buckle for easy wear.

For detailed diagrams on adjustment systems and wearing methods, please refer to the official user manual PDF: User Manual (PDF)

4. Operation

4.1 Magnetic Tail Light

The helmet is equipped with a rechargeable magnetic taillight for enhanced visibility and safety, especially during low-light conditions. The taillight features three flashing modes.

  • Attachment: The taillight attaches magnetically to the rear of the helmet.
  • Activation: Press the button on the taillight to cycle through the three flashing modes or turn it off.
  • Charging: The taillight is rechargeable. Use a standard USB charging cable (not included) to charge the unit. Ensure it is fully charged before use for optimal performance.

5. Maintenance & Cleaning

Proper care will extend the life of your helmet and maintain its protective qualities.

5.1 Cleaning the Helmet Shell

  • Clean your helmet only with lukewarm water, mild soap, and a soft cloth.
  • Gently wipe the exterior surfaces of the helmet with the damp cloth.
  • Allow your helmet to air dry completely after cleaning.
  • Avoid using aggressive cleaning agents, chemicals, solvents, bleaches, or strong detergents, as these can damage the helmet material and impair its protective effectiveness.
  • Do not apply paints or stickers to the helmet, as this can also compromise its integrity.

5.2 Cleaning the Inner Padding

The helmet features removable and washable IONIC+ antibacterial lining for hygiene and comfort.

  • First, remove the comfort padding from the helmet.
  • The comfort padding can be hand washed using lukewarm water and mild soap.
  • After washing, allow the padding to air dry completely before reinserting it into the helmet.
Close-up of the removable inner lining of the helmet, showing its mesh structure and Ionic+ branding.
Figure 4: Removable Inner Lining for easy cleaning and ventilation.

5.3 Storage

  • Store your helmet in a cool, dry place.
  • Avoid storing the helmet in high temperatures (starting at 60°C), as this can seriously damage the helmet, leading to uneven surfaces and blistering.
  • Do not store the helmet behind glass (e.g., in a car) or near heating sources.

5.4 Obsolescence and Replacement

  • A helmet must be replaced if it no longer fits properly.
  • It should be replaced at the latest, 6 years after the date of manufacture, even if no visible damage is present.
  • Regularly inspect your helmet for any visible defects.
  • A helmet subjected to a severe impact or deep scratch must be discarded and destroyed, as its protective function is compromised.

6. Troubleshooting

  • Helmet does not fit properly: If you cannot adjust the helmet size to prevent it from moving slightly forward or backward with the straps closed, do not use it. Exchange the helmet for a smaller or different model.
  • Helmet involved in an impact: Immediately discard and replace any helmet that has been subjected to a severe impact, even if no visible damage is apparent. The structural integrity may be compromised.
  • Damage from cleaning agents: If the helmet shows signs of damage (e.g., uneven surfaces, blistering) after using unauthorized cleaning agents, discontinue use and replace the helmet.

7. Specifications

Feature Detail
Model Number HT-068
Brand LUMDEER
Certification CE (EN 1078:2012+A1:2012), CPSC 16 CFR Part 1203
Material PC Shell + High-density EPS Liner
Weight Approximately 300g
Air Vents 23 (23-Channel Tornado Ventilation System)
Head Circumference M: 52-56cm, L: 57-62cm
Adjustment System 360-degree Adjustable Size Adjuster (Knob adjustment)
Buckle Type Advanced Magnetic Lock Buckle
Inner Lining Removable and Washable IONIC+ Ion Antibacterial Lining
Taillight Rechargeable Magnetic Tail Light (Three Flashing Modes)
Features Integrally Molded, Aerodynamic Design, Insect-proof net
Diagram showing the core technology analysis of the helmet, labeling components like PC case, EPS subject, breathable holes, nylon webbing, brand logo, regulator, and removable chin holder. Also lists product specifications.
Figure 5: Core Technology Analysis and Key Specifications.

8. Warranty & Support

For warranty claims, technical support, or any product-related inquiries, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty services.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.