FMS GOOSKY S2 Ultra Accessories

Contents

Goosky S2 Ultra Helicopter Accessories Instruction Manual

For Models: GOOSKY S2 Ultra

1. Introduction

This manual provides essential instructions for the proper installation, operation, and maintenance of original accessories for your Goosky S2 Ultra RC helicopter. Adhering to these guidelines will help ensure the longevity and optimal performance of your helicopter components. Please read this manual thoroughly before attempting any installation or operation.

Safety Warnings

  • Always operate RC models in open areas, away from people, animals, and obstacles.
  • Ensure all components are securely fastened before flight.
  • Keep fingers and loose clothing away from rotating parts.
  • Disconnect the battery when not in use or during maintenance.
  • This product is recommended for users aged 14 years and older.

2. Package Contents

Your Goosky S2 Ultra accessories package may include, but is not limited to, the following components:

  • Swashplate
  • Electronic Speed Controller (ESC)
  • Main Motor
  • Main Rotor Blade Set
  • Chassis Fixing Ring Set
  • Horizontal Axis Group
  • Double Hole Ball Head Linkage (Connecting Rods)
  • Servos (Steering Gear)
Overview of Goosky S2 Ultra Helicopter Accessories
Figure 2.1: Assortment of Goosky S2 Ultra Helicopter Accessories

3. Installation Guide (Setup)

Always refer to your Goosky S2 Ultra helicopter's main manual for specific disassembly and reassembly procedures. Ensure all connections are secure and components are correctly oriented. Use appropriate tools and avoid overtightening screws.

3.1 Swashplate Installation

Carefully install the new swashplate onto the main shaft. Ensure it moves smoothly without binding and is correctly aligned with the helicopter's control system. Verify that all ball links are securely attached.

Goosky S2 Ultra Swashplate
Figure 3.1: Goosky S2 Ultra Swashplate

3.2 Electronic Speed Controller (ESC) Connection

Connect the Electronic Speed Controller (ESC) to the main motor and the receiver. Pay close attention to the polarity of all connections (positive to positive, negative to negative) to prevent damage. Secure the ESC within the helicopter frame to prevent movement during flight.

Goosky S2 Ultra Electronic Speed Controller (ESC)
Figure 3.2: Goosky S2 Ultra Electronic Speed Controller (ESC)

3.3 Main Motor Mounting

Mount the main motor securely into its designated position. If applicable, ensure proper gear mesh between the motor pinion and the main gear to avoid excessive wear and noise.

Goosky S2 Ultra Main Motor
Figure 3.3: Goosky S2 Ultra Main Motor

3.4 Main Rotor Blade Set Attachment

Attach the main rotor blades to the rotor head. Ensure they are balanced and securely fastened with the provided hardware. Double-check that the blades are installed in the correct orientation for proper lift and control.

Goosky S2 Ultra Main Rotor Blade Set
Figure 3.4: Goosky S2 Ultra Main Rotor Blade Set

3.5 Double Hole Ball Head Linkage Installation

Install the double hole ball head linkages (connecting rods) between the swashplate and the rotor head components. Adjust the length of these linkages to achieve the correct control throws and zero pitch at mid-stick, as specified in your helicopter's main manual.

Goosky S2 Ultra Double Hole Ball Head Linkage
Figure 3.5: Goosky S2 Ultra Double Hole Ball Head Linkage

3.6 Chassis Fixing Ring Set Application

Use the chassis fixing rings to secure various components within the helicopter frame. These rings help to reduce vibration and prevent parts from shifting during aggressive maneuvers.

Goosky S2 Ultra Chassis Fixing Ring Set
Figure 3.6: Goosky S2 Ultra Chassis Fixing Ring Set

3.7 Horizontal Axis Group Assembly

Assemble and install the horizontal axis group, ensuring all bearings are smooth and the axis pivots freely. Secure it firmly to the rotor head assembly.

Goosky S2 Ultra Horizontal Axis Group
Figure 3.7: Goosky S2 Ultra Horizontal Axis Group

4. Operation Considerations

After installing any new accessories, it is crucial to perform a thorough pre-flight check and test flight. This ensures that all new components are functioning correctly and do not adversely affect the helicopter's stability or control.

4.1 Pre-Flight Checks

  • Verify all screws and fasteners on newly installed parts are tight.
  • Check for smooth movement of all control surfaces and linkages.
  • Ensure the ESC is properly calibrated with your transmitter.
  • Confirm battery is fully charged and securely mounted.
  • Perform a range check of your radio system.

4.2 Initial Test Flight

Conduct the first flight in a controlled environment. Start with low throttle and observe the helicopter's behavior. Gradually increase throttle and test basic controls (pitch, roll, yaw) to ensure proper response and stability. If any unusual behavior is observed, land immediately and re-inspect all components.

5. Maintenance

Regular maintenance of your Goosky S2 Ultra accessories is vital for optimal performance and safety.

  • Inspection: After every flight, visually inspect all accessories for signs of wear, cracks, bends, or loose connections. Pay particular attention to rotor blades, linkages, and motor mounts.
  • Cleaning: Keep components free from dirt, dust, and debris. Use a soft brush or compressed air for cleaning. Avoid using harsh chemicals that could damage plastics or electronics.
  • Lubrication: Apply a small amount of RC-grade lubricant to moving metal-on-metal parts, such as swashplate bearings and horizontal axis pivots, as needed. Avoid over-lubrication, which can attract dirt.
  • Storage: Store accessories in a dry, cool place away from direct sunlight and extreme temperatures.

6. Troubleshooting

Here are some common issues and their potential solutions related to your Goosky S2 Ultra accessories:

  • Excessive Vibration:
    • Check for unbalanced or damaged main rotor blades.
    • Inspect the horizontal axis group for bends or damage.
    • Ensure all screws, especially those on the motor and rotor head, are tight.
    • Verify chassis fixing rings are properly installed and secure.
  • Loss of Control or Erratic Flight:
    • Confirm all double hole ball head linkages are securely attached and not bent.
    • Check servo (steering gear) connections and functionality.
    • Ensure the swashplate moves freely and is correctly leveled.
  • Motor Not Spinning or Intermittent Power:
    • Verify the Electronic Speed Controller (ESC) is correctly connected to the motor and battery.
    • Check for any loose wires or damaged connectors on the ESC or motor.
    • Ensure the ESC is properly armed and calibrated with your transmitter.

7. Specifications

AttributeValue
Brand NameFMS
Model NumberGOOSKY S2 Ultra Accessories
UseVehicles & Remote Control Toys (Helicopters)
Recommended Age14+y
CertificationCE
Upgrade Parts/AccessoriesCar Shell (General category, specific parts listed above)
Remote Control Peripherals/DevicesMotor
RC Parts & AccsServos
Tool SuppliesAssembled class
OriginMainland China

8. User Tips

  • Thread-locking Compound: Always use a small amount of removable thread-locking compound (e.g., blue Loctite) on metal-to-metal screws, especially those on the rotor head and motor mounts. This prevents screws from loosening due to vibration during flight.
  • Spare Parts: Keep a stock of common wear-and-tear parts such as main rotor blades, tail rotor blades, and linkages. This ensures minimal downtime in case of damage.
  • Post-Crash Inspection: After any crash, no matter how minor, thoroughly inspect all components for hidden damage, cracks, or bends before attempting another flight. Even small imperfections can lead to catastrophic failure.
  • Balance is Key: Ensure your main rotor blades are perfectly balanced. Unbalanced blades can cause excessive vibration, leading to premature wear of bearings and other components.

9. Warranty and Support

For warranty information, technical assistance, or to report any issues with your Goosky S2 Ultra accessories, please contact the manufacturer, FMS, or your authorized dealer. Retain your purchase receipt as proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.