1. Introduction
Congratulations on your purchase of the Dancing Wings Hobby 1.58M Fokker-EIII Balsawood ARF RC Airplane. This model is a 1:6 scale replica of the iconic Fokker-EIII, designed for experienced RC pilots. This manual provides essential information for the assembly, setup, operation, and maintenance of your aircraft. Please read it thoroughly before beginning assembly or operation to ensure safe and enjoyable flying.
2. Safety Precautions
WARNING: Not suitable for children under 36 months due to small parts.
- Always operate your RC airplane in open areas, away from people, buildings, and obstacles.
- Never fly near airports, power lines, or public roads.
- Ensure your radio control system is fully charged and functioning correctly before each flight.
- Always perform a range check of your radio system before the first flight of the day.
- Keep hands and loose clothing away from the propeller when the motor is powered.
- Disconnect the battery immediately after flying and when performing maintenance.
- Do not attempt to catch the aircraft during flight.
- Always follow local regulations and laws regarding RC aircraft operation.
- This model is designed for outdoor use and requires an expert operator skill level.
3. Package Contents
The Dancing Wings Hobby Fokker-EIII is an ARF (Almost Ready to Fly) kit, meaning it requires assembly and the addition of a power system (motor, ESC, battery, servos, receiver) and a radio transmitter.
3.1. SCG2401 ARF Kit (Basic Package)
The basic ARF kit includes the balsawood airframe components and essential hardware for assembly:

Image: Layout of the Fokker-EIII ARF kit components, including fuselage, wings, tail sections, landing gear, and various small parts.
- Pre-built balsawood fuselage, wings, and tail sections
- Landing gear set
- Control horns and pushrods
- Small hardware (screws, nuts, linkages)
- Decal sheet (if applicable)
- Instruction manual (this document)
3.2. Optional Combo Packages (e.g., SCG2404)
Some packages may include additional electronic components. For example, the SCG2404 combo typically includes:

Image: Contents of the SCG2404 combo, showing the ARF kit alongside a motor, ESC, servos, a wooden propeller, and a Y-wire.
- SCG2401 Fokker-EIII ARF Kit
- Motor: MO2817 900KV
- ESC: 40A 4S
- Servos: 25g*2pcs, 9g*2pcs
- 50cm wire*2pcs
- Y wire*1pcs
- 12-inch wooden Propeller
Please verify your specific package contents upon receipt.
4. Specifications
| Feature | Specification |
|---|---|
| Model | SCG24 |
| Type | Balsawood ARF RC Airplane |
| Scale | 1:6 |
| Wingspan | 1580mm (62 inches) |
| Length | 1200mm (47 inches) |
| Flying Weight | Approx. 2.0 KG |
| Recommended Motor | 2815-2820 1000-900KV |
| Recommended ESC | 40A-60A |
| Recommended Battery | 4S LiPo 2200-2800mAh |
| Recommended Propeller | 12 inch |
| Recommended Servos | 9g*2pcs, 25g*2pcs |
| Required Radio | ≥4 Channel |
| Material | Wood |
| State of Assembly | Unassembled Kit |
| Remote Distance | 500m |
| Flight Time | 5~10 minutes |
| Control Channels | 4 channels |
| Operator Skill Level | Expert |
| Indoor/Outdoor Use | Outdoor |
5. Assembly and Setup
As an ARF kit, significant assembly is required. This section outlines general steps. Refer to detailed diagrams and instructions provided with your specific kit for precise guidance.
5.1. Tools and Materials Required (Not Included)
- Hobby knife or razor blade
- Various screwdrivers (Phillips, flathead)
- Pliers (needle-nose, regular)
- CA glue (thin, medium, thick) and accelerator
- Epoxy glue (30-minute recommended)
- Masking tape
- Ruler or measuring tape
- Drill and various drill bits
- Soldering iron and solder (for ESC/motor/battery connectors)
- Heat shrink tubing
- Servo extension leads (if needed)
- LiPo battery charger
- Radio transmitter (minimum 4-channel)
- Receiver
- Motor, ESC, Servos, Propeller (if not included in combo)
5.2. General Assembly Steps
- Wing Assembly: Carefully join wing halves (if applicable), install control horns, and connect pushrods to aileron servos. Ensure smooth, free movement.
- Tail Section Assembly: Attach the horizontal and vertical stabilizers to the fuselage. Install control horns for elevator and rudder, and connect pushrods to their respective servos.
- Landing Gear Installation: Securely attach the main landing gear and tail wheel assembly to the fuselage. Ensure wheels spin freely.
- Motor Installation: Mount the recommended motor to the firewall using appropriate screws. Ensure the motor is aligned correctly.
- ESC Installation: Mount the Electronic Speed Controller (ESC) in a location with good airflow, typically inside the fuselage near the motor. Connect the motor wires to the ESC.
- Servo Installation: Install all servos (aileron, elevator, rudder, throttle if applicable) into their designated locations. Connect pushrods and ensure correct throw.
- Receiver Installation: Mount the receiver securely inside the fuselage, away from the ESC and motor to minimize interference. Connect all servo leads and the ESC lead to the correct channels on the receiver.
- Battery Tray: Ensure the battery tray is secure and can accommodate your chosen LiPo battery.
- Propeller Installation: Attach the propeller to the motor shaft. Ensure it is balanced and securely tightened.
- Control Surface Setup: Adjust linkages to ensure all control surfaces (ailerons, elevator, rudder) are neutral when the transmitter sticks are centered. Set appropriate throws as per manufacturer recommendations or your preference.
- Center of Gravity (CG) Check: This is critical for stable flight. Balance the aircraft at the recommended CG point (usually marked on the plans or in the manual). Adjust battery position or add ballast as needed.
- Radio System Setup: Bind your receiver to your transmitter. Configure channel assignments, servo directions, and endpoint adjustments. Perform a full range check.
6. Operating Instructions
Operating an expert-level RC airplane requires practice and familiarity with its controls. Always start with small, controlled movements.
6.1. Pre-Flight Checks
- Ensure all control surfaces move freely and in the correct direction relative to stick inputs.
- Check all linkages and hinges for security.
- Verify the battery is fully charged and securely installed.
- Confirm the propeller is securely attached and undamaged.
- Perform a radio range check.
- Check for any loose wires or components.
- Ensure the flying area is clear of people and obstacles.
6.2. Takeoff
Video: The Fokker-EIII RC Airplane taking off from a paved surface and performing basic flight maneuvers.
- Place the aircraft on a smooth, level surface, facing into the wind.
- Advance the throttle slowly and smoothly.
- Use rudder input to maintain a straight takeoff roll.
- As speed increases, apply slight up-elevator to lift off.
- Once airborne, reduce throttle to a comfortable cruising speed and gain altitude.
6.3. Flight Controls
- Ailerons (Roll): Controlled by left/right movement of the right stick (Mode 2). Used for banking turns.
- Elevator (Pitch): Controlled by up/down movement of the right stick (Mode 2). Used for climbing and descending.
- Rudder (Yaw): Controlled by left/right movement of the left stick (Mode 2). Used for directional control on the ground and coordinated turns in the air.
- Throttle (Power): Controlled by up/down movement of the left stick (Mode 2). Adjusts motor speed.
6.4. Landing
- Approach the landing strip into the wind.
- Reduce throttle gradually to decrease speed and altitude.
- Maintain a controlled descent using elevator.
- As the aircraft nears the ground, apply a small amount of up-elevator to flare, reducing speed further.
- Touch down gently on the main landing gear, then allow the tail wheel to settle.
- Cut throttle completely and use rudder to steer the aircraft to a stop.

Image: The Fokker-EIII RC Airplane flying at a low altitude, demonstrating controlled flight.
7. Maintenance
Regular maintenance will prolong the life of your aircraft and ensure safe operation.
- After Each Flight:
- Inspect the airframe for any damage (cracks, dents, loose covering).
- Check all control linkages and hinges for wear or looseness.
- Ensure the propeller is free from nicks or cracks.
- Verify all screws and fasteners are tight.
- Check battery voltage and charge if necessary.
- Periodic Maintenance:
- Inspect motor mounts and connections.
- Check ESC for any signs of overheating or damage.
- Test servo functionality and ensure smooth operation.
- Clean the aircraft with a soft, dry cloth.
- Inspect wiring for fraying or damage.
- Storage: Store the aircraft in a cool, dry place, away from direct sunlight and extreme temperatures. Disconnect the battery when storing for extended periods.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Aircraft won't take off or lacks power | Low battery, incorrect propeller, motor/ESC issue, too heavy | Charge battery, check propeller size/direction, inspect motor/ESC, verify flying weight against specifications. |
| Unstable or erratic flight | Incorrect CG, loose control surfaces, radio interference, damaged airframe | Re-check CG, secure all linkages, perform range check, inspect airframe for damage. |
| Controls unresponsive or reversed | Incorrect servo direction, loose receiver connection, radio binding issue | Check servo directions on transmitter, ensure receiver connections are secure, re-bind radio. |
| Motor not spinning | Disconnected motor/ESC wires, ESC not armed, damaged motor/ESC | Check all connections, ensure throttle is at zero when connecting battery, inspect components for damage. |
9. User Tips
- Practice on a Simulator: Before flying your actual model, practice extensively on an RC flight simulator to familiarize yourself with controls and flight dynamics.
- Start with Low Rates: Configure your transmitter with dual rates or exponential settings to reduce control sensitivity for initial flights.
- Fly in Calm Conditions: For your first flights, choose a day with minimal wind to make learning easier and reduce the risk of damage.
- Observe Other Pilots: Learn from experienced RC pilots at your local flying field. They can offer valuable advice and assistance.
- Battery Management: Always monitor your battery voltage during flight. Land immediately if voltage drops significantly to prevent over-discharge and potential damage.
- Regular Inspections: Make pre-flight and post-flight inspections a habit. A quick check can prevent many common issues.
10. Warranty and Support
Dancing Wings Hobby products are manufactured to high standards. For any technical assistance, missing parts, or warranty claims, please contact your retailer or the manufacturer directly with your purchase details.
Please note that this is an ARF kit, and successful assembly and operation depend on the builder's skill and the quality of additional components used. Damage resulting from improper assembly, incorrect setup, or crashes is typically not covered under warranty.