Flipsky Mini Dual FSESC4.20 Plus

Contents

Flipsky 3-12S Mini Dual FSESC4.20 Plus ESC User Manual

High-Performance BLDC Controller with Anodized Aluminum Heatsink

1. Introduction

This manual provides essential information for the safe and effective use of your Flipsky 3-12S Mini Dual FSESC4.20 Plus Electronic Speed Controller (ESC). This high-performance BLDC controller is designed for various applications, particularly in Vehicles & Remote Control Toys, offering robust power management and precise motor control. Please read this manual thoroughly before installation and operation.

2. Package Contents

Upon opening the package, please verify that all the following items are included:

  • 1 x Dual FSESC4.20 Plus with Anodized Aluminum Heatsink
  • 1 x 16mm LED Button
  • 2 x VESC Sensor Wires
  • 1 x Micro USB Cable
  • 1 x User Manual (this document)
Flipsky Mini Dual FSESC4.20 Plus ESC and included accessories
Figure 1: Contents of the Flipsky Mini Dual FSESC4.20 Plus package, including the ESC, USB cable, sensor wires, and LED button.

3. Specifications

The Flipsky Mini Dual FSESC4.20 Plus offers the following technical specifications:

Feature Specification
Hardware Version V4.20
Firmware Version 5.2
Continuous Amps (Single) 50A
Continuous Amps (Dual) 100A
Burst Amps (Single) 150A
Burst Amps (Dual) 300A
Voltage Range 8V-60V (Safe for 3-12S LiPo batteries)
BEC Output 5V@1.5A
BEC Type Internal driver support
Timing Software calibration
Cutoff Voltage Programmable
Input Frequency PWM
Reverse Function Yes
Regenerative Braking Supported
Material Metal
Origin Mainland China
Use Vehicles & Remote Control Toys
Dimensions (approx.) 84mm (Length) x 64mm (Width) x 20.5mm (Height)
Dimensions of the Flipsky Mini Dual FSESC4.20 Plus ESC
Figure 2: Approximate dimensions of the ESC board.

4. Setup and Installation

Careful wiring is crucial for the proper function and longevity of your ESC. Refer to the diagrams below for correct connections.

4.1 Pinout Definitions

Pinout diagram for Flipsky Mini Dual FSESC4.20 Plus
Figure 3: Detailed pinout definitions for various ports on the FSESC4.20 Plus. This diagram shows connections for SENSE, CAN, USB, SWD, PPM+UART, and COMM ports, along with 3.3V, 5V, and ADC pins.

The pinout diagram (Figure 3) illustrates the various connection points on the ESC:

  • 1. SENSE: Used for motor current sensing.
  • 2. CAN: Controller Area Network for communication between multiple ESCs or other devices.
  • 3. USB: Micro USB port for connecting to a computer for configuration via VESC Tool.
  • 4. SWD: Serial Wire Debug for firmware development and debugging.
  • 5. Switch Connector: For connecting the included 16mm LED button.
  • 6. PPM+UART: Pulse Position Modulation and Universal Asynchronous Receiver/Transmitter for receiver and external module connections.
  • 7. CLK, DIO, RST, NC: Debugging/programming pins.
  • 8. USB: Additional USB port.
  • 9. CAN: Additional CAN port.
  • 10. SENSE: Additional motor current sensing.
  • 11. COMM: Communication port with 5V, 3.3V, ADC, TX, RX pins.
  • 12. COMM: Another communication port with 5V, 3.3V, ADC, TX, RX pins.

4.2 Wiring Diagram

Comprehensive wiring diagram for Flipsky Mini Dual FSESC4.20 Plus
Figure 4: Complete wiring diagram showing connections for battery, two motors, receiver (PPM input), and the LED power button.

Follow these steps for basic wiring, referring to Figure 4:

  1. Battery Connection: Connect your 3-12S LiPo battery to the main power input (red and black wires) of the ESC. Ensure correct polarity (red to positive, black to negative).
  2. Motor Connections: Connect the three phase wires from each motor to the corresponding A, B, C terminals on the ESC. For dual motor setups, connect Motor 1 to A1/B1/C1 and Motor 2 to A2/B2/C2.
  3. Sensor Wires (Optional): If your motors are sensored, connect the motor sensor wires to the designated sensor ports on the ESC.
  4. Receiver Connection: Connect your receiver's PPM output to the PPM input on the ESC (labeled as PPM+UART in Figure 3). Ensure 5V, GND, and signal wires are correctly aligned.
  5. LED Button: Connect the 16mm LED button to the dedicated switch connector (labeled as 'Switch Connector' in Figure 3 and '9' in Figure 4).
  6. USB Connection: Use the Micro USB cable to connect the ESC to your computer for initial configuration and firmware updates using the VESC Tool software.

Warning: Incorrect wiring can damage the ESC, motors, and battery. Always double-check connections before applying power.

5. Operating Instructions

The Flipsky Mini Dual FSESC4.20 Plus operates based on the VESC platform, requiring configuration via the VESC Tool software. This software allows for detailed customization of motor parameters, battery settings, input types, and safety features.

  1. Software Installation: Download and install the latest VESC Tool software from the official VESC project website or Flipsky's support page.
  2. Connect to PC: Connect the ESC to your computer using the provided Micro USB cable.
  3. Initial Setup: Launch VESC Tool. The software should detect the ESC. Follow the motor setup wizard to configure your motors. This includes detecting motor parameters, setting current limits, and configuring input devices (e.g., PPM remote).
  4. Power On/Off: Use the connected 16mm LED button to power the ESC on and off.
  5. Testing: After configuration, perform initial tests at low power and with the vehicle secured to ensure all settings are correct and motors respond as expected.

For detailed software configuration, refer to the comprehensive documentation and tutorials available for VESC Tool online.

6. Maintenance

To ensure optimal performance and longevity of your Flipsky Mini Dual FSESC4.20 Plus, follow these maintenance guidelines:

  • Keep Clean: Regularly inspect the ESC for dust, dirt, or debris. Clean with a soft brush or compressed air. Avoid using liquids directly on the board.
  • Temperature Management: Ensure adequate airflow around the ESC, especially during operation, to prevent overheating. The anodized aluminum heatsink helps dissipate heat, but proper ventilation is still important.
  • Connection Checks: Periodically check all wire connections (battery, motor, sensor, receiver) for looseness or damage. Secure any loose connections.
  • Firmware Updates: Keep the ESC firmware updated to the latest stable version using the VESC Tool. This can improve performance, add features, and fix bugs.
  • Storage: When not in use for extended periods, store the ESC in a dry, cool environment, away from direct sunlight and extreme temperatures.

7. Troubleshooting

If you encounter issues with your Flipsky Mini Dual FSESC4.20 Plus, consider the following common troubleshooting steps:

  • No Power:
    • Check battery connection and charge level.
    • Verify the LED button is correctly wired and functioning.
    • Inspect main power wires for damage or loose connections.
  • Motor Not Spinning/Irregular Behavior:
    • Ensure motor phase wires are correctly connected.
    • If using sensored motors, check sensor wire connections.
    • Reconnect to VESC Tool and re-run the motor detection wizard.
    • Check for error codes in VESC Tool's terminal or real-time data.
    • Verify receiver connection and signal.
  • Overheating:
    • Ensure adequate ventilation.
    • Check motor current limits in VESC Tool; they might be set too high for your application.
    • Verify motor and battery specifications match the ESC's capabilities.
  • Communication Issues (USB/CAN):
    • Try a different USB cable or port.
    • Ensure VESC Tool is the correct version for your firmware.
    • For CAN bus issues, check connections between multiple ESCs.

For more advanced troubleshooting, consult the VESC community forums or Flipsky's official support resources.

8. User Tips

No specific user tips were available from reviews or Q&A for this product. However, general tips for VESC-based ESCs include:

  • Always perform a motor detection in VESC Tool after any changes to motor or battery setup.
  • Start with conservative current limits and gradually increase them as you become familiar with the system.
  • Consider adding external capacitors if you experience voltage spikes, especially with long battery leads.
  • Regularly monitor temperatures during initial runs to ensure the ESC and motors are operating within safe limits.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty claims. Always refer to the official Flipsky website for the most up-to-date support information and resources.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.