1. Introduction
Thank you for choosing the Aigostar RGB Wireless Doorbell. This device is designed to provide a reliable and versatile alert system for your home, office, or other environments. Featuring 60 melodies, 5 adjustable volume levels, and a colorful indicator light, it offers convenience and customization. Please read this manual carefully before installation and use to ensure optimal performance and safety.
Figure 1: Key Features of the Aigostar Wireless Doorbell
2. Package Contents
Please check the package for the following items:
- 1 x Wireless Doorbell Transmitter (Button)
- 1 x Wireless Doorbell Receiver (Chime Unit)
- Mounting Hardware (Screws, Wall Anchors, Adhesive Pad)
- User Manual
3. Product Overview
3.1 Components and Controls
Figure 2: Receiver and Transmitter Components
- Receiver:
- Speaker: Emits the selected melody.
- Indicator Light: Provides visual alerts (colorful RGB).
- Previous/Mode Switching Button: Cycles through melodies backward or switches operating modes.
- Next/Code-learning Button: Cycles through melodies forward or initiates pairing.
- Volume/Code-clearing Button: Adjusts volume levels or clears pairing.
- Transmitter:
- 'Play' Button: Activates the doorbell chime.
- Indicator Light: Illuminates when the button is pressed.
4. Setup and Installation
4.1 Receiver Setup
- Plug the receiver into a standard electrical outlet in your desired location. Ensure it is within the 150M/500FT transmission range of the transmitter.
- The receiver will power on and be ready for pairing or operation.
4.2 Transmitter Installation
The transmitter (doorbell button) can be installed using either adhesive mounting or screw mounting.
Figure 3: Transmitter Installation Methods
Method 1: Adhesive Patch Mounting
- Clean the desired mounting surface thoroughly to ensure it is free of dust and moisture.
- Peel off one side of the protective film from the adhesive pad and stick it firmly to the back of the transmitter.
- Peel off the other side of the protective film and press the transmitter firmly onto the cleaned surface for at least 30 seconds.
Method 2: Screw Mounting
- Open the transmitter casing (usually by prying gently from the bottom or side with a small screwdriver).
- Place the back plate of the transmitter on the desired mounting surface and mark the positions for the screw holes.
- Drill pilot holes at the marked positions and insert wall anchors if necessary.
- Secure the back plate to the wall using the provided screws.
- Attach the transmitter front cover back onto the secured back plate.
4.3 Pairing (Code-learning)
The doorbell set is usually pre-paired from the factory. If re-pairing is needed or you add more transmitters/receivers:
- Plug in the receiver.
- Press and hold the 'Next/Code-learning' button on the receiver for approximately 3-5 seconds until the indicator light flashes rapidly. This indicates it's in pairing mode.
- Within 10 seconds, press the 'Play' button on the transmitter. The receiver will chime and its indicator light will flash, confirming successful pairing.
- To pair additional transmitters, repeat steps 2-3 for each new transmitter.
5. Operating Instructions
5.1 Changing Melodies
- Press the 'Next/Code-learning' button on the receiver to cycle through the 60 available melodies forward.
- Press the 'Previous/Mode Switching' button to cycle through melodies backward.
- Once you hear a desired melody, stop pressing the button. The receiver will save this selection.
5.2 Adjusting Volume
- Press the 'Volume/Code-clearing' button on the receiver repeatedly to cycle through the 5 volume levels (0-120dB).
- The receiver will indicate the current volume level with a chime or visual cue.
- The lowest volume setting typically activates a 'Mute Mode' where only the indicator light flashes.
5.3 Mute Mode
To activate Mute Mode, repeatedly press the 'Volume/Code-clearing' button until the volume reaches its lowest setting. In this mode, the receiver's indicator light will still flash when the doorbell is pressed, but no sound will be emitted.
5.4 Low Voltage Indicator
The transmitter is typically battery-powered. When the transmitter's battery is low, its indicator light may flash intermittently or fail to light up when pressed, or the signal range may decrease. Replace the battery promptly to ensure continuous operation.
6. Maintenance
6.1 Cleaning
Wipe the doorbell units with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the units in water.
6.2 Battery Replacement (Transmitter)
When the transmitter's battery is low, open the casing (refer to installation method 2 for guidance) and replace the old battery with a new one of the same type (e.g., 12V 23A or CR2032, depending on model). Ensure correct polarity.
6.3 Environmental Conditions
Figure 4: IP55 Rating and Temperature Range
The transmitter is IP55 dustproof and waterproof, suitable for outdoor use in various weather conditions. However, it should not be submerged in water. The operating temperature range is -10°C to 50°C (14°F to 122°F).
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Receiver does not chime |
|
|
| Short transmission range |
|
|
| Doorbell rings unexpectedly |
|
|
| Indicator light not working |
|
|
8. Specifications
| Feature | Specification |
|---|---|
| Brand | AIGOSTAR |
| Model | RGB Wireless Doorbell |
| Transmission Distance | Up to 150 meters (500 feet) in open areas |
| Melodies | 60 selectable chord sounds |
| Volume Levels | 5 levels (0-120dB) |
| Waterproof Rating (Transmitter) | IP55 (Dustproof and Waterproof) |
| Operating Temperature | -10°C to 50°C (14°F to 122°F) |
| Receiver Power Supply | AC (Socket Powered) |
| Transmitter Power Supply | Battery (Type may vary, typically 12V 23A or CR2032) |
| Receiver Dimensions | Approx. 8.5 cm (diameter) x 3.3 cm (thickness) |
| Transmitter Dimensions | Approx. 6.6 cm (height) x 3.5 cm (width) x 1.5 cm (thickness) |
| Package Weight | 0.15 kg |
| Package Dimensions | 8 cm x 8 cm x 6 cm |
9. User Tips
- Test Range: Before final installation, test the doorbell's transmission range by temporarily placing the transmitter and receiver in your desired locations to ensure reliable signal reception.
- Optimal Placement: Avoid mounting the transmitter on metal surfaces, as this can interfere with the wireless signal. For best results, mount it on wood, plastic, or masonry.
- Battery Check: Regularly check the transmitter's battery, especially if you notice a decrease in range or inconsistent operation.
- Multiple Uses: This doorbell is versatile and can be used in various settings beyond a front door, such as a call button for the elderly or disabled, or an alert system in a small office or workshop.
Figure 5: Versatile Applications
10. Warranty and Support
Aigostar products are designed and manufactured to the highest quality standards. For warranty information, technical support, or any questions regarding your product, please refer to the warranty card included in your package or contact the seller directly. Keep your purchase receipt as proof of purchase.
