DAKEFPV F7 MINI Flight Stack

Contents

DAKEFPV F7 MINI Flight Stack User Manual

Model: F7 MINI Flight Stack

Brand: DAKEFPV

1. Introduction

The DAKEFPV F7 MINI Flight Stack is a high-performance integrated solution for FPV drones, combining an F7 MINI Flight Controller (FC) and a 4-in-1 Mini Electronic Speed Controller (ESC). Designed for compact builds, it offers robust control and power delivery for demanding flight applications. This manual provides essential information for the proper installation, configuration, and operation of your flight stack.

2. Safety Precautions

  • Always disconnect the battery before performing any maintenance or wiring changes.
  • Ensure correct polarity when connecting power to avoid damage to components.
  • Work in a well-ventilated area.
  • Be aware of rotating propellers when the drone is powered; remove propellers during setup and testing.
  • Soldering should be performed by individuals with adequate experience to prevent short circuits or cold solder joints.
  • Keep the flight stack away from moisture, dust, and extreme temperatures.

3. Package Contents

Verify that all items are present in your package:

  • DAKEFPV F7 MINI Flight Controller
  • DAKEFPV Mini 4-in-1 ESC (55A, 60A, or 70A variant)
  • Power Cable (XT60 connector with red/black wires)
  • Capacitor
  • Various connection cables (e.g., for receiver, digital VTX)
  • Mounting hardware (nuts, washers, screws, silicone grommets)
DAKEFPV F7 MINI Flight Stack and included accessories
Image: DAKEFPV F7 MINI Flight Stack and included accessories, showing the FC, ESC, power cable, capacitor, various signal wires, and mounting hardware.

4. Specifications

Flight Controller (FC)

FeatureSpecification
MCUSTM32F722RET6
GYROMPU6000
BarometerSPL06-001
OSDAT7456E
Blackbox16MB
UART Ports5
I2CYes
BEC Output5V 2.5A
LED SupportYes
Buzzer SupportYes
Input Voltage3-6S Lipo
FirmwareDAKEFPVF722X8 (BETAFLIGHT/INAV)
Mounting Hole20.5 x 20.5mm
Digital VTX SystemSupports DJI / Vista / Walksnail

Electronic Speed Controller (ESC)

FeatureSpecification
Input Voltage3-6S Lipo
Continuous Current55A / 60A / 70A (variant dependent)
Peak Current65A / 70A / 80A (variant dependent)
FirmwareBLHeli_S
Mounting Hole20.5 x 20.5mm

5. Setup and Installation

5.1 Mounting

  • The flight stack uses a 20.5x20.5mm mounting pattern.
  • Use the provided silicone grommets and screws to securely mount the FC and ESC to your drone frame. Ensure the FC is oriented correctly (arrow pointing forward).
  • Avoid overtightening screws to prevent damage to the PCB.

5.2 Wiring Diagrams

Carefully follow the wiring diagrams below for connecting your peripherals. Incorrect wiring can cause permanent damage.

5.2.1 Digital VTX System (DJI / Vista / Walksnail) Wiring

Wiring diagram for DAKEFPV F7 MINI Flight Stack with DJI / Vista Digital VTX
Image: Detailed wiring diagram for connecting the DAKEFPV F7 MINI Flight Stack with a DJI / Vista Digital VTX, GPS, Receiver, Buzzer, LED, Camera, and Battery. Refer to the diagram for specific pin assignments for GND, 5V, 9V, UARTs (R6, T6, R4, T4, R2, T2), and other peripherals.
  • DJI Air Unit / Vista: Connect GND, 9V, R6 (RX), T6 (TX) to the corresponding pads on the FC.
  • GPS: Connect GND, 5V, R4 (RX), T4 (TX) to the FC.
  • Receiver (SBUS/PPM): Connect GND, 5V, R2 to the FC.
  • Receiver (S.PORT): Connect T2 to the FC.
  • Buzzer: Connect BUZ+ and BUZ- to the FC.
  • LED: Connect LED signal wire to the FC's LED pad.
  • Camera: Connect GND, 5V, CAM_IN, CAM_C to the FC.
  • Battery: Connect VBAT and GND from the ESC to your Lipo battery.
  • Motors: Connect M1-M4 from the ESC to your drone motors.

5.2.2 Analog VTX System Wiring

Wiring diagram for DAKEFPV F7 MINI Flight Stack with Analog VTX
Image: Detailed wiring diagram for connecting the DAKEFPV F7 MINI Flight Stack with an Analog VTX, GPS, Receiver, Buzzer, LED, Camera, and Battery. Refer to the diagram for specific pin assignments for GND, 5V, 9V, UARTs (R4, T4, R2, T2), VTX_IN, CAM_IN, and other peripherals.
  • Analog VTX: Connect GND, 9V, VTX_IN to the corresponding pads on the FC.
  • GPS: Connect GND, 5V, R4 (RX), T4 (TX) to the FC.
  • Receiver (SBUS/PPM): Connect GND, 5V, R2 to the FC.
  • Receiver (S.PORT): Connect T2 to the FC.
  • Buzzer: Connect BUZ+ and BUZ- to the FC.
  • LED: Connect LED signal wire to the FC's LED pad.
  • Camera: Connect GND, 5V, CAM_IN, CAM_C to the FC.
  • Battery: Connect VBAT and GND from the ESC to your Lipo battery.
  • Motors: Connect M1-M4 from the ESC to your drone motors.

5.3 Firmware Flashing

  • Connect the FC to your computer via a USB cable.
  • Open Betaflight Configurator or INAV Configurator (depending on your preferred firmware).
  • Select the target firmware DAKEFPVF722X8.
  • Flash the latest stable version of the firmware.
  • After flashing, perform a full chip erase and then load the default configuration.
  • Configure your receiver, motors, OSD, and other peripherals within the configurator software.

6. Operating Instructions

  • Once the flight stack is installed and configured, connect a fully charged Lipo battery.
  • Ensure your radio transmitter is powered on and bound to your receiver.
  • Perform pre-flight checks: verify motor direction, control surface response, and OSD data.
  • Arm the drone using your configured arming switch.
  • Fly responsibly and within your skill level.
  • Always disarm the drone before approaching it or handling it after a flight.

7. Maintenance

  • Regularly inspect all solder joints for cracks or cold connections.
  • Check all wiring for fraying or damage.
  • Keep the flight stack clean and free of dirt, dust, and debris. Use compressed air or a soft brush if necessary.
  • Avoid exposing the flight stack to excessive vibrations; ensure it is properly soft-mounted.
  • Periodically check for firmware updates for both the FC (Betaflight/INAV) and ESC (BLHeli_S) to benefit from performance improvements and bug fixes.

8. Troubleshooting

8.1 No Power / Intermittent Power

  • Check battery connection and polarity.
  • Inspect main power leads for secure soldering and continuity.
  • Ensure the capacitor is correctly installed and not damaged.

8.2 Motors Not Spinning / Incorrect Direction

  • Verify motor connections to the ESC.
  • Check motor protocol settings in Betaflight/INAV (e.g., DShot, OneShot).
  • Use the motor tab in Betaflight/INAV Configurator to test individual motors and adjust direction if needed (via BLHeliSuite32 or BLHeli_S Configurator).
  • Ensure ESC firmware is up to date.

8.3 No Signal from Receiver

  • Confirm receiver is powered and bound to your transmitter.
  • Check receiver wiring to the FC (GND, 5V, signal wire to correct UART RX pad).
  • Verify UART configuration and receiver protocol (e.g., SBUS, Crossfire, ELRS) in Betaflight/INAV.

8.4 OSD Not Displaying

  • Ensure camera and VTX are correctly wired to the FC.
  • Check OSD settings in Betaflight/INAV Configurator to enable and configure elements.
  • Verify that the OSD chip (AT7456E) is recognized by the FC.

9. User Tips

  • Soft Mounting: Always use the provided silicone grommets for soft mounting the flight stack. This helps reduce vibrations reaching the gyro, improving flight performance and stability.
  • Capacitor Installation: Solder the included low ESR capacitor directly to the main battery pads on the ESC. This helps filter electrical noise and protect the ESC from voltage spikes, especially on 6S setups.
  • Wiring Cleanliness: Keep your wiring as neat and short as possible. This reduces potential interference and makes troubleshooting easier.
  • Firmware Updates: Regularly check for the latest Betaflight/INAV firmware for your F722 MCU and BLHeli_S firmware for your ESCs. Updates often include performance enhancements and bug fixes.
  • Testing: Before your first flight, always perform a bench test with propellers removed. Check motor spin direction, receiver response, and OSD functionality.

10. Warranty and Support

DAKEFPV products are manufactured to high standards. For technical support or warranty inquiries, please contact the DAKEFPV RC Factory Store directly through the platform where the product was purchased. Please provide your order number and a detailed description of the issue.

© 2023 DAKEFPV. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.