1. General Introduction
The IP616 Smart Diagnostic System is a professional scan tool for vehicle diagnostics, based on the Android operating system. It supports multi-language switching and is suitable for different countries and regions. This device features a 7-inch touchable LCD screen for an intuitive user experience, powered by a 5000mAh, 3.65V lithium-polymer battery and an Android 10-based operating system. It includes 2G RAM and 32G ROM memory for smooth and fast operation.
The XTOOL IP616 V2.0 is an advanced automotive diagnostic scanner offering 10X faster all-system diagnostics, compatibility with over 150 brands from 1996 to 2025/2026, and advanced functions like ECU Configuration and Hidden Function Unlocking. It supports CAN FD, DoIP, and FCA new protocols and includes 34+ reset services.
Figure 1: XTOOL IP616 V2.0 Automotive Scanner highlighting key features.
Product Overview Video
Video 1: An overview of the XTOOL IP616 V2.0, demonstrating its features such as multiple services, vehicle brand coverage, language support, key programming, and update capabilities.
Tablet Components
The IP616 tablet includes the following components:
- Type-C Port
- DB15 Port
- Reset Hole
- Power Button
- Microphone
- Camera
- Speaker
- Nameplate
2. Safety Precautions
Please read this user manual carefully before using the Smart Diagnostic System. Pay attention to the words "Note" or "Caution" for appropriate operation.
Operation Instructions
- Keep the device away from heat or fumes when in use.
- If the vehicle battery contains acid, keep your hands and skin or fire sources away from the battery during testing.
- The exhaust gas of the vehicle contains harmful chemicals. Ensure adequate ventilation.
- Do not touch the vehicle cooling system components or exhaust manifolds when the engine is running due to high temperatures.
- Make sure the car is securely parked, Neutral is selected or the selector is at the P or N position to prevent the vehicle from moving when the engine starts.
- Make sure the (DLC) Diagnostic Link Connector is functioning properly before starting the test to avoid damage to the Diagnostic Computer.
- Do not switch off the power or unplug the connectors during testing. Doing so may damage the ECU (Electronic Control Unit) and/or the Diagnostic Computer.
Cautions!
- Avoid shaking, dropping or dismantling the Scan Tool as it may damage internal components.
- Use only your fingertips to touch the LCD screen. Hard or sharp objects may damage the Scan Tool.
- Do not use excessive force.
- Do not expose the screen to strong sunlight for a long period.
- Keep the Scan Tool away from water and moisture.
- Store and use the Scan Tool only within the temperature ranges identified in the Technical Specifications section.
- Keep the unit away from strong magnetic fields.
3. Setup: Vehicle Connection
Follow these steps to connect the IP616 Smart Diagnostic System to your vehicle:
- Press and hold the Power button to turn on the tablet.
- Select the App language and start the activation process.
- Input your E-mail address, and click OK to complete the activation.
- Connect the main cable to the tablet and tighten the screws.
- Plug the main test cable into the vehicle's DLC (Data Link Connector) port.
- Your tablet is now ready for diagnostic.
Figure 2: Connecting the main cable to the tablet.
Figure 3: Connecting the main test cable to the vehicle's DLC port.
4. Operating Instructions
4.1. Precautions for Diagnosis
- The voltage range on the car should be +9V to +36V DC.
- When testing special functions, operate according to prompts and meet test conditions (e.g., engine water temperature 80°C-105°C, headlights/AC off, accelerator pedal released).
- If unable to test or if test data is abnormal, search for the vehicle's ECU and select the menu for the model on the ECU nameplate.
- If the vehicle type or electronic control system is not found, upgrade the diagnostic software via the Updates menu or consult XTOOL technical service.
- Only use wiring harnesses provided by XTOOL to avoid damage.
- When running a Diagnostics function, do not shut down the device directly. Cancel the task before returning to the main interface.
4.2. Beginning Diagnostic Testing
After the tablet device is properly connected to the vehicle, you can start the vehicle diagnosis.
Vehicle Selection
The Scan Tool supports the following 3 ways to access the smart diagnostics system:
- AUTO SCAN: Supports automatic reading of vehicle VIN code. Ensure the car and device are well connected.
- MANUAL INPUT: Allows manual input of the 17-character VIN code for accurate results.
- SELECT VEHICLE BY AREA: Choose a car brand by selecting the appropriate region (e.g., Europe, America, Asia) and then the specific vehicle model.
Note: If your model is not recognized, try these steps:
- Update all software and check if the APP is updated in [Settings].
- Click Diagnosis on the main menu, manually select the engine system to read ECU information, and confirm if the VIN can be read.
- Contact the XTOOL technical team with the VIN code to confirm model support for automatic VIN identification.
Diagnosis Functions
The Scan Tool supports the following diagnostic functions:
- Read ECU Information
- Read/Clear Trouble Code (DTC)
- Read Live Data
- Freeze Frame
- Actuation Test (Bi-Directional Control)
- Special Functions
Figure 4: Full Systems Diagnosis interface.
Read ECU Information
This function reads ECU version information, including software/hardware versions, models, production date, and part numbers. This is useful for maintenance records and ordering new parts.
Read/Clear Trouble Code (DTC)
The diagnostic function can read ECU information, read and clear DTCs, and check live data and freeze frame data. If the device shows "System is OK" or "No Trouble Code", it means no related trouble code is stored or the troubles are not under ECU control. Most troubles are mechanical or executive circuit issues. Clear trouble codes only after resolving the underlying issues.
Read Live Data
Real-time information from various sensors (PIDs) helps identify problems. You can view live data in graph, text, list, column, and waveform formats. The IP616 supports 8 PIDs in one graph for better comparison and allows exporting data as CSV files.
Figure 5: 8-in-1 Live Data Graphing.
- Custom: Select and show multiple PIDs. Click "Display All" to show all PIDs.
- Combine: Combine different graphs into one chart for multiple PIDs.
- Data Recording: Record current data values. View recorded files in Reports -> Data Replay.
- Pause: Pause the recording timeline.
Freeze Frame
When a sensor signal is abnormal, the ECU saves data at that moment of failure as a freeze-frame to help analyze component failures. Freeze-frames vary by vehicle and model support. Users can click on a fault code to view the freeze frame, including context when the fault appeared and current context/additional data.
Actuation Test (Bi-Directional Control)
This function allows the device to send and receive information from vehicle control modules to test the working status of actuating components. Examples include turning on the radiator fan, modulating the throttle, operating windows/mirrors, turning on/off lights/horn, testing door locks, EVAP, ABS autobleed, A/C Configuration, Adaptive Headlamp Adjustment, etc.
Figure 6: Bi-Directional Control in action.
4.3. Special Functions
The IP616 supports 34+ special reset and re-learning functions for various vehicle systems. Functions may vary by vehicle. Always check compatibility.
Figure 7: Overview of 34+ Special Functions.
ABS Bleeding
This function bleeds air from the ABS system to restore braking sensitivity. Perform ABS bleeding when replacing the rear/front brake distributor pump, severe brake fluid shortage, or changing brake fluid.
Operation Guidelines:
- Read operating instructions and precautions on screen.
- Attach bleeder bottle to the left rear bleeder screw and open it.
- Click "OK" to start the bleed procedure, pumping the brake pedal continuously with steady applies every 2 seconds.
- Repeat for left front, right front, and right rear wheels.
- Stop pumping the brake pedal and close the right rear bleeder screw.
- Click "OK" to complete.
Caution:
- The ABS pump screw needs to be unscrewed.
- Brake fluid will be under pressure; secure the bleed hose and open bleeder screws slowly.
- Some vehicles may require manual bleeding.
Oil Reset
Resets the engine oil life system after an oil change. This ensures the system accurately calculates the next oil change interval.
Operation Guidelines:
- Enter the Oil Reset menu and choose relevant models.
- Follow on-screen instructions and press OK.
- Enter Maintenance mileage reset menu.
- Click INPUT, enter a reasonable value for remaining oil life, and press OK.
- Confirm the new value and press OK.
- A "Write successfully" message indicates completion.
EPB Reset
Resets the electronic parking brake system and brake pads. Useful for brake pad replacement, G-sensor and body angle calibration.
Operation Guidelines:
- Enter the EPB menu and choose relevant models.
- Follow on-screen instructions and press YES.
- Enter maintenance mode, release handbrake, and press OK.
- Wait for "Successful operation" message, then press OK.
- Enter Exit maintenance mode and wait for "Successful operation" message.
SAS (Steering Angle Sensors) Calibration
Calibrates the steering wheel position as the straight-ahead position. Required after replacing steering angle sensor, mechanical parts, four-wheel alignment, or car body repair.
Operation Guidelines:
- Enter the SAS menu and choose relevant models.
- Enter the Set steering angle sensor menu and follow instructions.
- Wait for instructions and press YES.
- Follow instructions and press OK.
- Wait for instructions and press OK.
- "Function execution is completed" message indicates success.
BMS Reset
Resets the monitoring unit of the vehicle battery, clears low battery fault information, and performs battery matching. Required when the main battery is replaced.
Operation Guidelines:
- Enter the BMS Reset menu and choose relevant models.
- Turn on the ignition switch.
- Press OK to continue.
- Enter battery capacity (0-255Ah) and press OK.
- Enter the battery manufacturer and press OK.
- Enter the 10-digit battery serial number and press OK.
Injector Coding
Writes the identification code of the fuel injector into the ECU. Required after ECU or injector replacement to ensure accurate fuel injection control.
Operation Guidelines:
- Enter the Injector coding menu and choose relevant chassis models.
- Enter the Fuel injection nozzle injection volume adjustment menu.
- Read the note carefully and press OK.
- Read and confirm the value stored in the cylinders.
- Enter the Change the value of cylinder menu, input the new 5-digit value, and press OK.
- Wait for "Write successfully" message.
- Turn off the ignition switch.
- Wait for prompt to turn on ignition switch.
- Re-enter the Fuel injection nozzle injection volume adjustment menu to verify new values.
DPF Regeneration
Manages Diesel Particulate Filter regeneration, component replacement teach-in, and teach-in after ECM replacement. Clears PM from the DPF filter.
Operation Guidelines:
- Enter the DPF menu and choose relevant models.
- Enter the DPF regeneration menu.
- Read requisites carefully and press OK.
- Read fuel tank level and carbon deposit load.
- Choose "drive to warm up" and follow instructions, then press OK.
- Read instructions carefully and press OK.
- Follow instructions and press OK.
- Press OK to start regeneration.
- Wait for carbon deposit value to decrease and "Emergency regeneration has been completed" message (up to 40 minutes).
- Wait 2 minutes for the particulate filter to cool down.
- Press "drop out" to exit.
TPMS Reset
Performs learning, matching, and resetting functions for tire pressure sensors. Required for tire replacement, troubleshooting TPMS issues, or loss of signal.
Operation Guidelines (Automatic Relearn):
- Install tire pressure sensor.
- Adjust all TPMS sensors to standard value.
- Keep vehicle standstill for 20+ minutes (engine off, power off).
- Drive at 30-100km/h for 15+ minutes.
- Vehicle will automatically relearn values; tire pressure warning will disappear.
- If relearn fails, repeat steps 2-5.
Operation Guidelines (Static Relearn):
- Install all TPMS sensors.
- Pull up the parking brake.
- Turn ignition to ON/RUN (engine off).
- Enter tire pressure learning mode via instrument panel.
- Starting from left front wheel, use TPMS Activation Tool to activate sensor.
Note: The first sensor should be learned within 2 minutes, otherwise repeat step 4.
Operation Guidelines (OBD Relearn):
- A TPMS Activation Tool is needed.
- Install tire pressure sensor.
- Adjust all TPMS sensors to standard value.
- Activate all sensors in order: left front, right front, right rear, left rear.
- Connect TPMS Activation Tool to OBD port and perform OBD relearn.
- Turn ignition to ON/RUN, re-trigger all sensors in order.
- Keep vehicle powered off for 25+ minutes.
- Drive at 30-100km/h for 15+ minutes.
Operation Guidelines (Copy ID Relearn - Method 1):
- Use TPMS Activation Tool to activate original sensor, copy ID to activation device.
- Program copied ID into new sensor via TPMS Activation Tool.
- Remove original sensor, install programmed new sensor, and put tire back on.
Operation Guidelines (Copy ID Relearn - Method 2):
- Use TPMS Activation Tool to connect vehicle OBD port, enter tire pressure system, copy ID of sensor to be replaced.
- Program copied ID into new sensor via TPMS Activation Tool.
- Remove original sensor, install programmed new sensor, and put tire back on.
Operation Guidelines (Copy ID Relearn - Method 3):
- Remove the original sensor.
- Use the TPMS Activation Tool to copy the original sensor ID into the new sensor manually.
- Install the new sensor to the tire, set tire pressure to standard value, and put the tire back on.
Note:
- Tire pressure standard is usually displayed in the vehicle owner's manual, on a label next to the driver's door (near the B-pillar), in the drawer next to the driver's seat, or on the fuel tank cap.
- This Scan Tool is not a replacement for a professional TPMS activation tool; it only provides TPMS Reset/Relearn functions, not activation of TPMS sensors. Consult your local dealer for a professional TPMS activation tool.
4.4. Update & Factory Reset
Update
After activating the device, update software modules via the "Updates" screen. The device identifies all available software packages for download directly via the Internet. Access this by opening the Diagnostic application and clicking "Updates".
Note:
- After contacting XTOOL Support to change the language configuration, you need to download all software packages on the device again.
- When the subscription expires, installed software remains available, but updates will be invalid. XTOOL is not responsible for restoring software deleted due to personal operation.
- To renew your subscription, contact your local dealer or XTOOL technical support.
Factory Reset
Restoring factory settings in Android OS erases custom settings and data, then restarts the device. Trigger a factory reset by clicking "Settings" from the main home page, then "Backup & reset". Follow on-screen prompts. After reset, select your language in the initial interface.
4.5. Remote Assistance
Use the TeamViewer QuickSupport program for remote assistance. This allows XTOOL's technical support to control your tablet remotely. The device generates a unique ID that remains constant. Ensure the tablet is connected to the Internet.
Steps to obtain remote support:
- Turn on the tablet.
- Click "Remote" in the Diagnostic application; the TeamViewer screen displays the device ID.
- Your support partner must install the full TeamViewer program on their computer.
- Provide your ID to the partner/technician.
- A pop-up window will ask for permission to control your device.
- Click "Allow" to accept or "Reject" to decline.
5. Troubleshooting: DTC Status Descriptions
Understanding Diagnostic Trouble Code (DTC) statuses is crucial for effective troubleshooting:
| DTC Status | Description | Suggestions |
|---|---|---|
| Current/Present | DTCs stored in the ECU when both continuous and non-continuous (2 trip) monitors fail. MIL (Malfunction Indicator Lamp) illuminates instantly. | Can be cleared using the Scan Tool's Clear DTCs function, or when the ECU monitor completes 40 consecutive trips without a fault. |
| History/Stored | DTCs stored when continuous and non-continuous monitors (2nd trip) fail. Not cleared by the ECU monitor. | Can only be cleared using the Clear DTC function of the Scan Tool. |
| Pending | Codes that self-prepare when a fault is determined. A preliminary investigation for your engine. A random malfunction can occur during the current drive cycle but only happen for a second. | Typically not severe, but shouldn't be ignored. Can be cleared using the Clear DTC function. |
| Permanent | DTCs stored in the ECU when continuous and non-continuous monitors fail. Set in conjunction with Current and History DTCs. | Cannot be cleared using the Clear DTCs function. Cleared when the ECU monitor completes and passes three consecutive trips. |
| Active/Static (For Volkswagen) | Fault is happening at the moment and needs immediate attention. | Cannot be cleared directly by the Scan Tool. The internal fault of the car must be eliminated manually. |
| Passive/Sporadic | Fault occurred in the past. | Can be cleared by Scan Tool. User should check if the DTC reappears. |
6. Specifications
| Attribute | Value |
|---|---|
| Model Name | XTOOL IP616 Car Diagnostic Tool |
| Brand Name | XTOOL |
| Operating System | Android 10 |
| Display | 7 inch Touch Screen with 1024x600 Resolution |
| Memory | 2G(RAM) + 32G(ROM) |
| Power and Battery | 5000mAh, 3.65V lithium-polymer battery |
| Item Weight | 2.5kg |
| Item Height | 14.2cm |
| Item Width | 3cm |
| Item Length | 24.9cm |
| Material | plastic |
| Wireless Function | No |
| Wireless Support | No |
| Measurement Accuracy | ±0.3% |
| External Testing Certification | ce |
| Certification | CE |
| Origin | Mainland China |
| Software Version | Newest |
| Hardware Version | 2026 |
| Car Coverage | for VW, for Benz Mercedes W205, W204, W212, for VW, for BMW, for Skoda, for Audi, for Chrysler, for Toyota, etc. (10,000+ vehicles worldwide) |
| Update | lifetime free software update |
| Warranty | 2 year warranty |
Package Contents
Figure 8: XTOOL IP616 Packing List.
- XTOOL IP616 Tablet
- VAG to OBDII Main Cable
- Type-C to C Charger Cable
- Quick Guide & Packing List
- Color Carton
7. User Tips
- Compatibility Check: Functions vary by vehicle. Always check compatibility for your specific vehicle Make/Model/Year/VIN before attempting any special functions or key programming. You can contact XTOOL support for this.
- Software Updates: Ensure your Diagnosis APP is updated to the latest version (Settings > APP). Language authorization is no longer required, and you can freely change it. If automatic updates fail, contact technical staff for assistance.
- Key Programming: Not all cars support key programming. Always verify compatibility for your specific car model with the seller before purchasing if this is a critical feature for you.
- EU Version Restriction: The EU Version of the IP616 has an IP limit and can only be used in European areas (e.g., Spain, France, Poland, Germany, Russia, UK). It will NOT work in other countries. The Global Version has no such IP limit.
- FCA AutoAuth: For 2018+ FCA vehicles (Fiat, Chrysler, Dodge, Jeep), the IP616 V2.0 provides access to the security gateway module. This allows for clearing fault codes and performing special functions. No special FCA 12+8 cable is needed, but you will need to log in to your FCA account.
Figure 9: IP616 EU Version IP Restrictions.
8. Warranty and Support
The XTOOL IP616 V2.0 Automotive Scanner comes with a 2-year warranty.
After-Sales Services
For technical support or inquiries, please contact XTOOL:
- E-Mail: supporting@xtooltech.com
- Tel: +86 755 21670995 or +86 755 86267858 (China)
- Official Website: www.xtooltech.com
For remote assistance, refer to the "Remote Assistance" section in the operating instructions.
9. Compliance Information
FCC Compliance
FCC ID: 2AW31P902
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information: This device meets government requirements for exposure to radio waves. The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. This device was tested for typical body-worn operations with the back of the device kept 0mm from the body. Use accessories that maintain a 0mm separation distance and do not contain metallic components.
Responsible Party: TianHeng Consulting, LLC, 392 Andover Street, Wilmington, MA 01887, United States.
ISED Statement
IC: 29441-P902
PMN: Smart Diagnostic System
HVIN: P902
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
CAN ICES (B) / NMB (B).
This device meets the exemption from the routine evaluation limits in section 6.6 of RSS 102 and compliance with RSS 102 RF exposure. The device for operation in the band 5150-5350 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
CE Declaration of Conformity
Hereby, Shenzhen XTOOLtech Intelligent Co., Ltd declares that this Smart Diagnostic System is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.
UKCA
Hereby, Shenzhen XTOOLtech Intelligent Co., Ltd declares that this Smart Diagnostic System satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body.