Skydroid 3-in-1 Camera/Receiver/LED Light

Contents

Skydroid 3-in-1 Camera/Receiver/LED Light Instruction Manual

Model: 3-in-1 Camera/Receiver/LED Light

Compatible with Skydroid T12, H12, and M12 Remote Controls

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Skydroid 3-in-1 Camera/Receiver/LED Light unit. This versatile device integrates a camera, a digital receiver, and powerful LED lights into a single waterproof unit, designed for use with various remote-controlled vehicles such as drones, intelligent robots, and underwater drones. It is compatible with Skydroid T12, H12, and M12 remote control systems.

Front view of the Skydroid 3-in-1 Camera/Receiver/LED Light unit
Figure 1: Front view of the 3-in-1 unit, showcasing the central camera and two LED lights.

2. Setup and Installation

Follow these steps to properly install and connect your 3-in-1 unit:

  1. Unpacking: Carefully remove the 3-in-1 unit and all accessories from its packaging.
  2. Mounting: Securely mount the 3-in-1 unit to your vehicle (drone, robot, etc.) in a position that provides an unobstructed view for the camera and optimal light distribution from the LEDs.
  3. Antenna Connection: Connect the two antennas to the digital receiver module. Ensure they are oriented for best signal reception.
  4. Wiring Connections: Refer to the wiring diagram below for proper connections. The unit requires external power and connects to your remote control system via S.bus or PWM.
    • Connect the red and black power wires to a suitable power source on your vehicle.
    • Connect the 'to S.bus' wire to the S.bus port on your flight controller or compatible device.
    • Connect the 'to camera' wire to the designated camera input on your system.
    • Connect the 'to data' wire for data transmission, if applicable to your setup.
  5. Remote Control Pairing: Ensure your Skydroid T12, H12, or M12 remote control is properly paired with the digital receiver. Refer to your remote control's manual for specific pairing instructions.
Wiring diagram for Skydroid 3-in-1 unit showing connections to S.bus, camera, and data, along with antennas.
Figure 2: Wiring diagram for connecting the 3-in-1 unit to your system.
Back view of the 3-in-1 unit with power and signal wires connected.
Figure 3: Back view of the 3-in-1 unit showing wire connections.

3. Operating Instructions

The Skydroid 3-in-1 unit functions as a camera, a digital receiver, and an LED light system. Its operation is integrated with your Skydroid remote control and connected devices.

  1. Power On: Once all connections are secure, power on your vehicle and the Skydroid remote control. The unit will initialize automatically.
  2. Camera Operation: The integrated camera provides real-time video feedback. This feed can be viewed on compatible devices such as cell phones, iPads, or PCs connected to your M12 remote control system.
  3. LED Light Control: The super bright LEDs are designed for night navigation and enhanced visibility. Control of the LED lights (e.g., on/off, brightness) is typically managed through your remote control's auxiliary channels or a dedicated function within the Skydroid system software.
  4. Digital Receiver Functionality: The unit acts as a digital receiver, processing signals from your remote control (T12, H12, M12) and transmitting data to your vehicle's flight controller via S.bus or PWM.
Digital Graph Control Link System diagram showing connections between remote control, receiver, and various devices.
Figure 4: Overview of the Digital Graph Control Link System.

4. Maintenance

To ensure the longevity and optimal performance of your Skydroid 3-in-1 unit, follow these maintenance guidelines:

  • Cleaning: Wipe the unit with a soft, dry cloth to remove dust and debris. For stubborn dirt, a slightly damp cloth can be used, ensuring no moisture enters any exposed ports (though the unit is waterproof, proper care is always recommended).
  • Waterproof Feature: The unit is designed to be waterproof. However, avoid prolonged submersion or exposure to high-pressure water jets unless specifically rated for such conditions. After exposure to water, ensure the unit is dry before storage or next use.
  • Storage: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures.
  • Cable Inspection: Periodically inspect all cables and connectors for signs of wear, fraying, or damage. Replace any damaged components immediately.

5. Troubleshooting

If you encounter issues with your 3-in-1 unit, refer to the following troubleshooting tips:

  • No Power:
    • Check all power connections to ensure they are secure and correctly wired (red to positive, black to negative).
    • Verify that the power source on your vehicle is functioning correctly and providing adequate voltage.
  • No Camera Feed/Signal Loss:
    • Ensure the 'to camera' wire is securely connected.
    • Check the connection between your remote control and the digital receiver.
    • Verify that your viewing device (phone, iPad, PC) is properly connected to the remote control and the Skydroid app/software is running correctly.
    • The unit utilizes 2.4G wireless broadband. Ensure there is no significant interference from other 2.4G devices. The system is designed with double antenna and model redundancy to enhance communication ability, even with weak signals.
    • Avoid operating in environments with known unstable frequency bands (e.g., crowded 433MHz or 915MHz bands, though the 2.4G system aims to mitigate this).
  • LED Lights Not Functioning:
    • Confirm that the LED control function on your remote control is activated and configured correctly.
    • Check the power supply to the unit.
  • Remote Control Not Responding:
    • Re-check the S.bus/PWM connection to your flight controller.
    • Ensure your remote control is fully charged and properly paired with the digital receiver.
Diagram illustrating powerful transmission links between remote control and 3-in-1 unit.
Figure 5: Powerful Transmission Links overview.

6. Specifications

Product Specifications
Feature Description
Product Type 3-in-1 Camera, Digital Receiver, LED Light
Brand Skydroid
Model Number Night Camera (specific variant)
Compatibility Skydroid T12, H12, M12 Remote Controls
Dimensions (L x H x W) 105mm x 43mm x 25mm
Material Composite Material, Full CNC finishing
LED Features Super bright LED, 150° Convex lens, Digital receiver for night navigation lights
Camera Features Night Camera capability
Connectivity S.bus / PWM
Wireless Transmission 2.4G wireless broadband, Double antenna, Model redundancy design
Power Source External (No internal battery, not electric, not charger/adapter)
Water Resistance Waterproof
Diagram showing the dimensions (105mm, 43mm, 25mm) and key features of the 3-in-1 unit.
Figure 6: Dimensions and key features of the 3-in-1 unit.

7. User Tips

  • Optimal Antenna Placement: For the best signal reception, ensure the two antennas are positioned away from large metal objects and are not obstructed by the vehicle's frame or other components.
  • Power Management: Since the unit draws power from the vehicle, monitor your vehicle's battery life, especially when using the bright LEDs for extended periods.
  • Firmware Updates: Regularly check the official Skydroid website or app for any firmware updates for the receiver or remote control, as these can improve performance and add new features.

8. Warranty and Support

For any technical assistance, warranty claims, or support inquiries regarding your Skydroid 3-in-1 Camera/Receiver/LED Light unit, please contact the seller or the official Skydroid customer support. Keep your purchase receipt as proof of purchase.

Please note that specific warranty terms and conditions may vary based on your region and point of purchase. Always refer to the warranty information provided at the time of purchase.

© 2024 Skydroid. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.