hiwheel Motor-F25/F30, Motor-F40

Contents

hiwheel Replacement Rear Hub Motor User Manual

For Ninebot F20, F25, F30, F40 E-Scooters

1. Introduction

This manual provides detailed instructions for the safe and effective installation, operation, and maintenance of your new hiwheel Replacement Rear Hub Motor. This motor is designed as a direct-fit replacement for Ninebot F20, F25, F30, and F40 series E-Scooters, ensuring optimal performance and compatibility. Please read this manual thoroughly before attempting any installation or use.

Two hiwheel replacement rear hub motors for Ninebot scooters, showing front and back views.
Figure 1: hiwheel Replacement Rear Hub Motor (Front and Rear Views)

2. Compatibility

This hiwheel Rear Hub Motor is specifically designed for the following Ninebot E-Scooter models:

  • Ninebot F20 E-Scooter
  • Ninebot F25 E-Scooter
  • Ninebot F30 E-Scooter
  • Ninebot F40 E-Scooter

Ensure your scooter model matches one of the listed compatible models before proceeding with installation.

3. Package Contents

Upon opening the package, please verify that all components are present and undamaged:

  • 1 x hiwheel Replacement Rear Hub Motor (pre-assembled with tire)
  • User Manual (this document)

If any items are missing or damaged, please contact customer support immediately.

4. Specifications

FeatureDetail
Brandhiwheel
Product CategoryScooter accessories
Compatible ModelsNinebot F20, F25, F30, F40 E-Scooters
Item Number (Model)Motor-F25/F30, Motor-F40
OriginMainland China
Package Length40 cm
Package Width30 cm
Package Height10 cm
Package Weight5.1 kg

5. Safety Warnings

WARNING: Improper installation or use can lead to serious injury or damage to your scooter. Always follow these safety guidelines:

  • Always disconnect the scooter's battery before beginning any installation or maintenance.
  • Wear appropriate personal protective equipment (PPE), including gloves and eye protection.
  • If you are unsure about any step, consult a qualified technician or refer to the official Ninebot service manual for your specific scooter model.
  • Ensure all connections are secure and properly insulated after installation.
  • Do not modify the motor or its wiring.
  • Keep children and pets away from the work area.

6. Installation Guide

This section outlines the general steps for replacing the rear hub motor. Specific details may vary slightly depending on your Ninebot model. For a comprehensive guide, please refer to the official Ninebot service manual for your scooter.

Tools Required:

  • Wrench set (appropriate sizes for axle nuts)
  • Screwdriver set (Phillips and flathead)
  • Wire cutters/strippers (if wiring needs modification, though this is a direct-fit)
  • Electrical tape or heat shrink tubing (for insulation)
  • Zip ties (for cable management)

6.1. Preparation

  1. Power off your Ninebot E-Scooter completely and disconnect the battery.
  2. Place the scooter on a stable surface, preferably elevated, to allow easy access to the rear wheel.
  3. Carefully remove any plastic covers or fenders that obstruct access to the rear wheel and motor wiring.

6.2. Removing the Old Motor

  1. Locate the motor's electrical connections. These typically consist of three thicker phase wires (often yellow, blue, brown) and a thinner hall sensor wire bundle.
  2. Carefully disconnect all electrical connectors. Note their positions for re-connection.
  3. Using the appropriate wrench, loosen and remove the axle nuts securing the rear wheel to the scooter frame.
  4. Gently remove the old rear wheel/motor assembly from the scooter frame.
Rear view of the motor with wiring and QR code on the hub, showing electrical connections.
Figure 2: Rear Hub Motor Electrical Connections
Detailed close-up of the three-phase motor wiring terminals (yellow, blue, brown) with heat shrink insulation.
Figure 3: Close-up of Motor Wiring Terminals

6.3. Installing the New Motor

  1. Carefully position the new hiwheel rear hub motor assembly into the scooter frame, aligning the axle with the dropouts.
  2. Install the axle nuts and tighten them securely. Do not overtighten, but ensure the wheel is firmly seated and does not wobble.
  3. Reconnect all electrical connectors. Match the phase wires (yellow, blue, brown) and the hall sensor wire bundle to their corresponding connections. Ensure a snug and secure fit.
  4. Use electrical tape or heat shrink tubing if any connections require additional insulation.
  5. Route the motor cables neatly and secure them with zip ties to prevent them from snagging or interfering with moving parts.
  6. Reinstall any covers or fenders that were removed in the preparation step.

6.4. Post-Installation Check

  1. Double-check all connections and fasteners to ensure they are secure.
  2. Reconnect the scooter's battery.
  3. Turn on the scooter and perform a functional test. Slowly rotate the rear wheel by hand to ensure it spins freely without obstruction.
  4. Engage the throttle gently to confirm the motor spins correctly.
  5. Test the brakes to ensure they are functioning properly with the new wheel installed.
  6. Perform a low-speed test ride in a safe, open area to confirm full functionality before regular use.

7. Operation

The hiwheel Replacement Rear Hub Motor functions identically to the original motor in your Ninebot E-Scooter. No special operation procedures are required beyond the standard use of your scooter. Refer to your Ninebot E-Scooter's original user manual for detailed operating instructions.

  • Ensure the motor is properly installed and all connections are secure before each ride.
  • Avoid riding through deep water or in extremely wet conditions to protect the motor's electrical components.
  • Do not overload the scooter beyond its specified weight capacity, as this can strain the motor.

8. Maintenance

Regular maintenance helps prolong the life and performance of your hiwheel Rear Hub Motor.

  • Cleaning: Periodically clean the exterior of the motor and wheel with a damp cloth. Avoid using high-pressure water jets directly on the motor.
  • Inspections: Regularly inspect the motor for any signs of physical damage, loose wires, or corrosion. Check the tire pressure and tread wear.
  • Fasteners: Ensure all bolts and nuts securing the motor and wheel are tight. Re-tighten if necessary.
  • Wiring: Check the motor's electrical wiring for fraying, cuts, or loose connections. Repair or replace damaged wiring immediately.

9. Troubleshooting

If you encounter issues with your hiwheel Replacement Rear Hub Motor, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Motor not spinningLoose electrical connections, disconnected battery, faulty controller, motor damage.Check all wiring connections. Ensure battery is connected and charged. Consult a technician if controller or motor is suspected faulty.
Unusual noises from motorForeign object in motor, bearing wear, internal damage.Inspect for debris. If noises persist, motor may require professional inspection or replacement.
Reduced power or speedLow battery, tire pressure, motor overheating, controller issue.Charge battery fully. Check and adjust tire pressure. Allow motor to cool. Consult a technician.
Wheel wobbleLoose axle nuts, damaged wheel bearing, bent axle.Tighten axle nuts. Inspect wheel bearings and axle for damage. Replace if necessary.

For issues not listed here, or if solutions do not resolve the problem, please contact customer support or a certified scooter repair specialist.

10. User Tips

Based on common user feedback for scooter motor replacements:

  • Cable Management: Pay extra attention to routing the motor cables to prevent pinching or rubbing against other components, which can lead to premature wear.
  • Torque Settings: If available, use a torque wrench to tighten axle nuts to the manufacturer's specified torque settings for your Ninebot model to ensure both security and prevent damage.
  • Pre-Ride Check: Always perform a quick visual inspection and functional check of the motor and wheel before each ride, especially after installation or maintenance.

11. Warranty and Support

For warranty information regarding your hiwheel Replacement Rear Hub Motor, please refer to the terms and conditions provided at the time of purchase. Keep your proof of purchase for any warranty claims.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact the seller or hiwheel customer service. You may also find additional resources, including a detailed user manual in PDF format, at the following link:

View User Manual (PDF)

When contacting support, please have your product model (Motor-F25/F30, Motor-F40) and purchase details ready.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.