1. Product Overview
The ANENG GN302 is a high-performance handheld digital anemometer designed for precise measurement of wind speed, ambient temperature, and humidity. It features an LCD display with a maximum count of 9999 and supports various units for wind speed and air volume. This device is suitable for a wide range of applications including environmental monitoring, wind energy assessment, meteorological analysis, and industrial or agricultural use.
Video: ANENG GN302 Digital Anemometer Product Overview and Demonstration. This video shows the unboxing, battery installation, power-on sequence, unit switching for wind speed, air volume measurement setup, and temperature/humidity measurement capabilities.
Image: High Precision Anemometer highlighting features such as wind speed level display, wind speed and volume measurement, and temperature and humidity measurement.
2. Setup
2.1 Unboxing
Upon receiving your ANENG GN302 Anemometer, carefully open the packaging. The box should contain the anemometer unit and a user manual.
Image: The ANENG GN302 Anemometer shown with its packaging box and user manual.
2.2 Battery Installation
The ANENG GN302 requires two AAA batteries (not included in shipment) for operation. Follow these steps to install the batteries:
- Locate the battery compartment cover on the back of the anemometer.
- Use a screwdriver to remove the screw securing the battery compartment cover.
- Carefully remove the cover.
- Insert two AAA batteries, ensuring correct polarity (+/-).
- Replace the battery compartment cover and secure it with the screw.
Image: Back view of the ANENG GN302 Anemometer, illustrating the battery compartment and overall dimensions.
3. Operating Instructions
3.1 Device Layout and Controls
Image: Diagram of the ANENG GN302 Anemometer with labels for its components and display elements, including Impeller, Temperature and humidity sensor, Power and backlight on/off key, Unit selection/number setting key, Switch key for setting air volume/wind, Temperature reading value, Humidity reading value, Wind force level, Low battery prompt, Gear position display, Test value display area, Wind speed unit, and Air volume unit.
3.2 Power On/Off and Backlight
- Power On/Off: Long press the power button (labeled 'BL' or power symbol) to turn the device on or off.
- Backlight: Long press the power button to turn on the screen backlight.
3.3 Wind Speed Measurement
- Power on the device.
- Point the impeller towards the wind source.
- The wind speed will be displayed on the LCD screen.
- Unit Selection: In wind speed mode, short press the 'UNIT' button to switch between different wind speed units: knots, km/h, mil/h, m/s, ft/s, ft/m.
Image: The anemometer display showing various wind speed and air volume units, along with button functions for unit selection and data hold.
3.4 Air Volume Measurement
- Power on the device.
- Press the 'VEL FLOW/AREA' button briefly to switch between FLOW and VEL modes.
- To measure air volume, you must first set the cross-sectional area of the air duct. Long press the 'VEL FLOW/AREA' button to enter the section setting mode.
- Adjust the value as needed.
- After setting the value and exiting, the air volume can be measured.
- Unit Selection: In air volume mode, short press the 'UNIT' button to switch between air volume units: CMM, CFM, CMS.
3.5 Temperature and Humidity Measurement
The device automatically measures and displays ambient temperature and humidity. These readings are shown on the LCD screen alongside wind speed or air volume measurements.
Image: The ANENG GN302 Anemometer in use, displaying wind speed and temperature/humidity readings.
3.6 Data Hold and Max/Min Values
- Data Hold: Press the 'HOLD MAX/MIN' button briefly to open/close data holding, which locks the current display reading.
- Max/Min Values: Long press the 'HOLD MAX/MIN' button to switch between displaying the maximum (MAX) and minimum (MIN) measured values.
3.7 Automatic Shutdown
The device features a 15-minute automatic shutdown function to conserve battery life. This function can be canceled if continuous operation is required (refer to the full manual for details on disabling this feature).
Image: The ANENG GN302 Anemometer illustrating the 'No Operation Automatic Shutdown' feature, which activates after 15 minutes of inactivity.
4. Specifications
| Feature | Specification |
|---|---|
| Model Number | ANENG GN302 Anemometer |
| Type | Anemometer |
| Display | LCD four-digit, maximum display 9999 |
| Screen Size | 33x36mm |
| Sampling Rate | 5 times/second |
| Wind Speed Measurement Range | 0.4~30.00 m/s |
| Wind Speed Accuracy | ±(2%+2) |
| Beaufort Wind Force Level | 0~12 levels |
| Humidity Measurement Range | 0%~100%RH |
| Humidity Accuracy | ±2 %RH |
| Temperature Measurement Range | -20.0℃~60.0℃ |
| Temperature Accuracy | ±2℃ |
| Measurement Units | knots, km/h, mil/h, m/s, ft/s, ft/m; CMM, CFM, CMS |
| Resolution | 0.01/0.1/1 |
| Extended Parameters | Maximum value, minimum value, air volume measurement |
| Data Retention | Lock display reading |
| Auto Power Off | 15 minutes (can be canceled) |
| Power Supply | 2 x AAA batteries (not included) |
| Size | 17.5cm x 5cm x 2.9cm (6.9in x 1.98in x 1.17in) |
| Weight | 82g |
| Battery Included | No |
| Origin | Mainland China |
| Certification | None |
5. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents.
- Storage: When not in use for extended periods, remove the batteries to prevent leakage. Store the anemometer in a cool, dry place away from direct sunlight and extreme temperatures.
- Impeller Care: Ensure the impeller is free from dust, debris, or obstructions for accurate readings. Avoid touching the impeller blades directly.
6. Troubleshooting
- Device not powering on: Check if the batteries are installed correctly and have sufficient charge. Replace with new AAA batteries if necessary.
- Inaccurate readings: Ensure the impeller is clean and unobstructed. Verify that the correct measurement unit is selected.
- Display issues: If the display is dim or flickering, replace the batteries.
- No response from buttons: Try removing and reinserting the batteries to reset the device.
7. User Tips
- For consistent air volume measurements, ensure the cross-sectional area is accurately set for the duct or opening being measured.
- When measuring wind speed, hold the anemometer steady and ensure the impeller is directly facing the airflow for optimal accuracy.
- The device is versatile for various environments, including laboratory and outdoor settings.
Image: The ANENG GN302 Anemometer being used for laboratory environmental measurement.
Image: The ANENG GN302 Anemometer being used for outdoor environmental measurement.
8. Warranty and Support
For any issues, technical support, or warranty inquiries, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific contact information.
