Riseem STN1020RFW

Contents

Riseem STN1020RFW WiFi Smart Thermostat User Manual

Non-programmable Smart Life WiFi Smart 915MHZ PTAC TUYA APP RF Wireless Thermostat

1. Introduction

Thank you for choosing the Riseem STN1020RFW WiFi Smart Thermostat. This non-programmable thermostat is designed for use with PTAC (Packaged Terminal Air Conditioner) units and offers smart control through WiFi (2.4G/5G) and RF (915MHZ) connectivity. It is compatible with the TUYA APP and Alexa, providing flexible and energy-saving comfort control for your environment. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your device.

Riseem STN1020RFW WiFi Smart Thermostat and Wireless Receiver
Figure 1: Riseem STN1020RFW WiFi Smart Thermostat and Wireless Receiver

2. Key Features

  • Universal WiFi (2.4GHZ/5.0GHZ) connectivity for smart control.
  • Compatible with Alexa for voice control.
  • Supports Universal 2H/1C Heat Pump or 1H/1C Conventional, or 2H/2C Conventional systems.
  • Heating and Cooling Set Point Limits for precise temperature management.
  • Separate heating and cooling swing (cycle rate) adjustments.
  • Non-Programmable design for straightforward operation.
  • White/Blue/Green backlight options for clear display.
  • Universal sub-base for easy installation.
  • Room temperature calibration adjustments.
  • Mounts on wall or junction box.
  • Power options: Battery or 24V AC.

3. Package Contents

Your package should contain the following items:

  • Riseem STN1020RFW WiFi Smart Thermostat (Main Unit)
  • Wireless Receiver Unit with pre-attached wiring harness
  • Mounting Hardware (screws, wall anchors)
  • User Manual (this document)
Wireless Receiver Unit with Wires
Figure 2: Wireless Receiver Unit

4. Thermostat Quick Reference

Thermostat Quick Reference Diagram showing LCD, Fan Switch, System Switch, Temperature Setpoint Buttons, and Face Door access.
Figure 3: Thermostat Controls and Display Overview

LCD Display Indicators:

  • Room Temperature: Indicates the current room temperature.
  • Set At: Displays the user-selectable setpoint temperature.
  • System Operation Indicators: The COOL, HEAT, or FAN icon will display when the respective mode is active. Note: The compressor delay feature is active if these icons are flashing. The compressor will not turn on until the 5-minute delay has elapsed.
  • Fan Mode Indication: Shows current fan setting (On, Auto, Low, High).
  • Low Battery Indicator: When not connected to 24VAC, replace batteries when this indicator flashes. If battery voltage is ultra-low (less than 2.4V), only battery symbols will flash. Press any button to restore normal display. After 120 seconds of no operation, the screen will only flash battery symbols.

Controls:

  1. LCD Display: Shows temperature and system status.
  2. Fan Switch: Controls fan operation (ON/AUTO).
  3. System Switch: Selects system mode (COOL/OFF/HEAT).
  4. Temperature Setpoint Buttons (+/-): Adjusts the desired temperature.
  5. Switch Face Door: Use the finger bevel on the lower portion of the thermostat to open the easy access panel for switches.

5. Installation

Important: Installation should be performed by a qualified technician. Disconnect power to the heating/cooling system before installation to prevent electrical shock or equipment damage.

5.1 Mounting the Thermostat

  1. Turn off power to the heating and cooling system at the main power panel.
  2. Remove the old thermostat from the wall.
  3. Separate the front cover of the new thermostat from its sub-base.
  4. Mount the sub-base directly to the wall or to a junction box using the provided screws and wall anchors. Ensure the 'UP' arrows on the sub-base are pointing upwards.
  5. Proceed to wiring the receiver and thermostat.
Thermostat Mounting Plate with Wiring Terminals
Figure 4: Thermostat Mounting Plate

5.2 Wiring the Receiver and Thermostat

The STN1020RFW system consists of a main thermostat unit and a wireless receiver. The receiver handles the direct wiring to your HVAC system, while the thermostat communicates wirelessly with the receiver.

Receiver Wiring:

Connect the wires from your HVAC system to the corresponding terminals on the wireless receiver. Refer to the diagram below for terminal designations. The receiver requires a 24V AC power supply (18-30V AC).

Back of Thermostat with Wiring Terminals Labeled
Figure 5: Thermostat Wiring Terminals (Main Unit)
Back of Thermostat with Wiring Terminals Labeled
Figure 6: Thermostat Wiring Terminals (Alternative View)

Terminal Designations:

  • R: 24V AC (Heating)
  • C: Common (24V AC)
  • O/B: Reversing Valve (Heat Pump)
  • GL: Fan Low Speed
  • GH: Fan High Speed
  • W: Heat Stage 1
  • Y: Cool Stage 1
  • W2: Heat Stage 2
  • Y2: Cool Stage 2

After wiring the receiver, attach the thermostat main unit to its sub-base. Restore power to the system.

6. Operation

6.1 Powering the Thermostat

The thermostat can be powered by either 24V AC (18-30V AC) or two AAA 1.5V batteries. If using batteries, ensure they are correctly inserted into the battery compartment located on the back of the thermostat.

Back of Thermostat showing Battery Compartment
Figure 7: Thermostat Battery Compartment

6.2 Setting System Mode

Use the System Switch (located behind the face door, see Figure 3) to select your desired operating mode:

  • HEAT: Activates the heating function.
  • OFF: Turns off both heating and cooling.
  • COOL: Activates the cooling function.

6.3 Setting Fan Mode

Use the Fan Switch (located behind the face door, see Figure 3) to select your desired fan operation:

  • ON: The fan runs continuously.
  • AUTO: The fan runs only when the heating or cooling system is actively operating.

6.4 Adjusting Temperature

Use the Temperature Setpoint Buttons (+/-) on the front of the thermostat to increase or decrease the desired temperature. The 'Set At' display will show your target temperature.

6.5 Backlight Operation

Press any button to activate the backlight. The backlight will remain on for 15 seconds after the last button press. If no buttons are pressed, the backlight will turn off to conserve energy.

6.6 Smart Control (TUYA APP / Alexa)

To utilize the smart features, ensure your thermostat is connected to your WiFi network (2.4GHz or 5GHz). Follow the instructions provided with the TUYA APP or Alexa device to pair and control your thermostat remotely.

7. Maintenance

7.1 Battery Replacement

If your thermostat is battery-powered, replace the 2x AAA 1.5V alkaline batteries immediately when the low battery icon Low battery icon appears on the display. Failure to do so may result in your heating & cooling system becoming inoperable, leading to freezing or overheating conditions.

7.2 Cleaning

Clean the thermostat's exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure no moisture enters the device.

8. Troubleshooting

  • Thermostat not powering on: Check 24V AC connection to the receiver or replace AAA batteries in the thermostat unit.
  • System not responding to thermostat: Ensure the wireless receiver is powered and correctly wired to the HVAC system. Verify the thermostat is within range of the receiver and that there are no significant obstructions.
  • Temperature display shows 'LO' or 'HI': 'LO' indicates room temperature below 0℃ (32℉), and 'HI' indicates room temperature above 40℃ (99℉). This is normal operation for extreme temperatures.
  • Compressor not turning on immediately: The thermostat has a 5-minute compressor delay protection. This is normal, and the system operation icon will flash during this delay.
  • WiFi connectivity issues: Ensure your WiFi network is 2.4GHz or 5GHz. Check your router and internet connection. Re-pair the thermostat with the TUYA APP if necessary.

9. Specifications

ItemValue
ModelSTN1020RFW
Application TypeConventional or heat pump; Wi-Fi 2.4GHZ, 5.0GHZ (Smart Life); Works With Alexa
Stages H/C - Conventional2H/2C
Stages H/C - Heat Pump3H/2C heat pump w/o auxiliary or emergency heat
System Operation ModeHEAT, OFF, COOL
Fan Operation ModeAUTO, LOW, HIGH
ProgrammingNon-programmable
Terminal DesignationsR, C, O/B, GL, GH, W, Y, W2, Y2
Backlight ColorWhite/Blue/Green
Heating And Cooling Set Point LimitsYES
Compressor Delay Protection5 minutes
Temperature Display Range0~40℃ (32~99℉)
Temperature Control Range7~32℃ (44~90℉)
Accuracy±1℉ (on 68℉)
Shipping Temperature14°F ~ 150°F (-10°C ~ 65°C)
Operation Ambient Temperature32°F ~ 122°F (0°C ~ 50°C)
Operating Humidity90% non-condensing maximum
Power Supply (Thermostat)2*AAA alkaline batteries or 18~30 VAC NEC Class II, 50/60Hz
Power Supply (Receiver)18~30 VAC NEC Class II, 50/60Hz
Load Rating1 amp per terminal, 1.5 amp maximum all terminals combined (18~30V)
Display Size5.58 sq.in. (3604mm²)
Physical Dimensions (Thermostat)4.72" W x 3.85" H x 1.02" D (120mm W*98mm H*26mm D)
Physical Dimensions (Receiver)3.81" W x 1.81" H x 1.02" D (97mm W*46mm H*26mm D)
Mounting MeansMounts on wall or junction box
Wireless Operating Frequency915MHZ

10. User Tips

No specific user tips were available from the provided reviews or Q&A content. However, general best practices for smart thermostats include:

  • Ensure your WiFi network is stable for consistent smart control.
  • Place the thermostat away from direct sunlight, drafts, or heat sources for accurate temperature readings.
  • Regularly check battery levels if not hardwired to 24V AC.

11. Warranty and Support

11.1 Warranty

The Riseem STN1020RFW thermostat comes with a 1-year warranty covering any defects in quality or workmanship. Repairs within this period are free of charge.

11.2 After-Sale Service

For technical assistance, troubleshooting, or any issues related to your thermostat, online technical support is available. Please contact the seller for return and replacement procedures if necessary.

12. Frequently Asked Questions (FAQ)

Q: Do you offer guarantee for the products?
A: Yes, we provide a 1-year warranty.
Q: Can you provide your certificates?
A: Our product has CE, RoHS, and FCC certificates. Please inquire if other certificates are needed.
Q: Is it OK to print my logo on the thermostats?
A: Yes, logo printing is possible. Please formally inform us before production and confirm the design based on our samples.

13. Product Overview Video

Watch this video for a quick overview of various thermostat models, including the STN1020RFW.

Video 1: Overview of Riseem Thermostat Models

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.