Flipsky 5085

Contents

Flipsky 5085 140KV 2500W Waterproof Brushless DC Motor User Manual

Model: 5085 | Brand: Flipsky

1. Introduction

This manual provides essential information for the safe and effective use of your Flipsky 5085 140KV 2500W Waterproof Brushless DC Motor. Designed for high-performance applications such as electric hydrofoils (eFoils), underwater thrusters, and electric surfboards, this motor offers robust power and reliable operation in marine environments. Please read this manual thoroughly before installation and operation.

2. Safety Information

  • Always disconnect power before performing any installation, maintenance, or inspection.
  • Ensure all electrical connections are secure and properly insulated to prevent short circuits and water ingress.
  • Operate the motor within its specified voltage and current limits to prevent damage and ensure safety.
  • Keep hands, hair, and loose clothing clear of rotating parts, especially the propeller, during operation.
  • This motor is designed for underwater use (IP58 rated), but ensure all associated electronic speed controllers (ESCs) and power sources are also adequately protected for the intended environment.
  • Do not exceed the maximum operating temperature of 100℃.

3. Product Overview

The Flipsky 5085 motor is a powerful brushless DC motor featuring a robust design suitable for demanding aquatic applications. It is available with either a front or rear output shaft to accommodate various mounting configurations.

Flipsky 5085 motor showing both front and rear output shaft options
Figure 3.1: Flipsky 5085 Motor with Rear and Front Output Shafts
Flipsky 5085 motor with front output shaft and propeller
Figure 3.2: Flipsky 5085 Motor (Front Output Shaft) with Propeller
Flipsky 5085 motor with rear output shaft and propeller
Figure 3.3: Flipsky 5085 Motor (Rear Output Shaft) with Propeller
Video 3.1: Product showcase of the Flipsky 5085 motor, demonstrating its design and features.

4. Specifications

AttributeValue
ProductFlipsky 5085
MaterialMetal
Voltage Range6-14S
Rated Voltage48V
Rated Current30A
Max Current50A
Rated Power1500W
Max Power2500W
No-Load Current1.1A
Max Thrust19.9
Max Operating Temperature100℃
Slots & Poles12N/14P
Three-Phase Leads14AWG
Length of Lead Wire1200mm
Connector4mm Banana head
Shaft8mm
Waterproof and Dustproof RatingIP58
Weight0.84kg
Motor Specifications (Diameter*Length)49.5mm * 85.0mm

4.1 Thrust Test Data

Thrust Test Data Table for Flipsky 5085 motor
Figure 4.1: Thrust Test Data. This table details load current, power, speed, and thrust (in kgf and N) at various voltages (24V, 30V, 42V, 48V).

4.2 Dimensional Drawings

Dimensional drawing for Flipsky 5085 motor with rear output shaft
Figure 4.2: Dimensional Drawing for Rear Output Shaft Motor. Shows overall dimensions, mounting hole patterns (4-M4*5), shaft diameter (8mm), and wire length (1200mm).
Dimensional drawing for Flipsky 5085 motor with front output shaft
Figure 4.3: Dimensional Drawing for Front Output Shaft Motor. Shows overall dimensions, mounting hole patterns (4-M4*5), shaft diameter (8mm), and wire length (1200mm).

5. Setup

Proper setup is crucial for the performance and longevity of your motor. Follow these general guidelines:

  1. Mounting: Securely mount the motor using the designated mounting holes. Ensure the mounting surface is flat and rigid to prevent vibrations. Refer to the dimensional drawings (Figures 4.2 and 4.3) for precise measurements.
  2. Propeller Installation: Attach the propeller to the motor shaft. Ensure it is correctly oriented and tightened securely to prevent loosening during operation. Use any provided washers or nuts as instructed.
  3. Electrical Connections: Connect the motor's three-phase leads (14AWG with 4mm banana heads) to a compatible Electronic Speed Controller (ESC). Ensure correct phase matching (typically A-A, B-B, C-C, or adjust if motor spins in the wrong direction). The ESC must be rated for the motor's voltage and current requirements (6-14S, up to 50A max current).
  4. Water Cooling (if applicable): While the motor is waterproof, ensure any external water cooling systems for the ESC or battery are properly installed and functioning if your setup requires them.
  5. Pre-Operation Check: Before full power operation, perform a low-power test to confirm correct rotation direction and smooth operation.

6. Operating Instructions

Once the motor is properly installed and connected to an ESC and power source, follow these steps for operation:

  1. Power On: Turn on your power source and ESC. Listen for any initialization beeps from the ESC.
  2. Throttle Control: Gradually increase the throttle input from your remote control or control system. The motor should begin to spin smoothly.
  3. Monitor Performance: During operation, monitor the motor's temperature and overall performance. Avoid prolonged operation at maximum load if overheating occurs.
  4. Power Off: Always reduce throttle to zero before powering off the system. Disconnect the battery or power source when not in use.

7. Maintenance

Regular maintenance will extend the life and ensure optimal performance of your Flipsky 5085 motor:

  • Cleaning: After each use, especially in saltwater, rinse the motor thoroughly with fresh water to remove salt, sand, and debris. Allow it to dry completely.
  • Inspection: Periodically inspect the motor for any signs of wear, corrosion, or damage to the casing, shaft, and wires. Check propeller for damage.
  • Connections: Ensure all electrical connections remain tight and free from corrosion.
  • Storage: Store the motor in a clean, dry place away from direct sunlight and extreme temperatures.

8. Troubleshooting

If you encounter issues with your motor, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Motor does not spinNo power, loose connections, faulty ESC, motor damageCheck battery charge, verify all connections, test ESC, inspect motor for visible damage.
Motor spins in wrong directionIncorrect phase wiringSwap any two of the three motor phase wires connected to the ESC.
Motor overheatsOverload, insufficient cooling, faulty ESC settingsReduce load, ensure adequate water flow for cooling, check ESC settings for proper timing/current limits.
Unusual noise or vibrationDamaged propeller, loose mounting, foreign object, bearing wearInspect propeller for damage, tighten mounting screws, remove any obstructions, check motor bearings.

9. User Tips

  • Voltage Compatibility: The motor is designed for a voltage range of 6-14S (approximately 22.2V to 58.8V nominal). Always ensure your battery and ESC are compatible with this range to prevent damage.
  • Propeller Selection: Experiment with different propeller sizes and pitches to find the optimal balance between thrust and efficiency for your specific application.
  • ESC Configuration: Proper ESC configuration (e.g., motor timing, PWM frequency) can significantly impact motor performance and efficiency. Consult your ESC manual for detailed settings.

10. Warranty and Support

For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.