1. Introduction
Thank you for choosing the ANDELI MIG-135Plus Semi-automatic 3-in-1 Welding Machine. This versatile inverter welder supports MIG (Gasless Flux-Cored), Lift TIG, and MMA (Stick) welding processes, making it suitable for a wide range of applications from home DIY to professional workshops. This manual provides essential information for safe and effective operation, setup, maintenance, and troubleshooting of your welding machine.
2. Important Safety Warnings
Always prioritize safety when operating welding equipment. Failure to follow these instructions may result in serious injury or death.
- Electric Shock Can Kill: Do not touch live electrical parts. Wear dry welding gloves and protective clothing. Ensure the work area is dry.
- Fumes and Gases Can Be Hazardous: Keep your head out of the fumes. Use ventilation or exhaust to remove fumes from the breathing zone.
- Arc Rays Can Burn Eyes and Skin: Wear a welding helmet with a proper shade filter. Wear appropriate eye protection with side shields. Wear protective clothing (leather gloves, long sleeves, etc.).
- Fire and Explosion Hazard: Remove all flammables from the welding area. Have a fire extinguisher readily available. Do not weld on containers that have held combustibles.
- Hot Parts Can Cause Severe Burns: Allow welded materials and equipment to cool before handling.
- Magnetic Fields: Pacemaker wearers should consult their doctor before operating welding equipment.
- Noise: Excessive noise can damage hearing. Wear ear protection.
- Maintenance: Only qualified personnel should perform maintenance. Disconnect power before servicing.
3. Package Contents
Verify that all items are present and undamaged upon unpacking:
- ANDELI MIG-135Plus Welding Machine
- Welding Helmet (Auto-darkening)
- Ground Clamp
- Electrode Holder
- MIG Torch
- Flux-Cored Welding Wire (2lb spool)
- Contact Tips
- Gas Nozzle
4. Key Features
- 4-in-1 Multi-Process: Supports SYN MIG, MAN MIG, FLUX MMA, and LIFT TIG welding.
- 4.1-Inch Precision LED Display: Large, clear display for real-time data, protected by a transparent cover.
- High-Power 135A Output: Capable of welding mild steel plates up to 2/5” thick.
- Dual-Voltage Versatility: Operates on both 110V and 220V power supplies.
- Smart Synergic Control Technology: Automatically optimizes voltage and wire feed speed based on amperage or wire diameter.
- Advanced Protection System: Includes automatic voltage compensation, over-current, overload, overheating, and over-voltage protection.
- 2T/4T Settings: Manual and automatic trigger modes for various welding scenarios.
- Compact and Portable: Lightweight design for easy transport.
5. Specifications
| Parameter | Value |
|---|---|
| Brand Name | ANDELI |
| Model Number | MIG-135PLUS (NO.:W24121200010001) |
| DIY Supplies | Electrical |
| Frequency | 50/60Hz |
| Origin | Mainland China |
| Type | Combination (MIG/MMA/TIG) |
| Material | Nylon (for certain components) |
| High-concerned chemical | None |
| Standard Compliance | ENIEC 60974-1:2019 |
| No-load Voltage (U0) | 56V |
| Output Current/Voltage (110V) | 20A/15V (20%), 135A/20.8V (60%), 60A/17V (100%) |
| Output Current/Voltage (220V) | 20A/15V (20%), 135A/25.4V (60%), 60A/22.4V (100%) |
| Max Input Current (I1MAX) | 56A (110V), 28A (220V) |
| Effective Input Current (I1eff) | 25A (110V), 12.5A (220V) |
| Protection Grade | IP21S |
| Insulation Grade | F |
| Cooling Method | Air-cool |
| Dimensions (H x W x D) | 12.99" x 5.91" x 9.37" |
| Weight | 9.1 LB |
6. Setup
6.1 Power Connection
- Ensure the welding machine is turned off and unplugged.
- Select the appropriate power source: 110V for standard outlets or 220V for higher power applications. The machine automatically detects the voltage.
- Connect the power cord to a suitable grounded electrical outlet.
6.2 Wire Spool Installation (MIG/Flux-Cored)
- Open the wire feed compartment.
- Place the 2-pound flux-cored welding wire spool onto the spindle, ensuring it rotates freely.
- Thread the welding wire through the wire feed mechanism and into the MIG torch liner.
- Close the wire feed compartment.
6.3 Torch and Ground Clamp Connection
- Connect the MIG torch to the designated connector on the front panel.
- Connect the ground clamp cable to the negative (-) terminal on the front panel.
- Connect the electrode holder cable to the positive (+) terminal for MMA welding, or the TIG torch for Lift TIG welding.
- Ensure all connections are secure.
6.4 Protective Cover
Ensure the transparent protective cover is properly installed over the LED display to shield it from impacts, sparks, and debris.
7. Operating Instructions
7.1 Power On and Mode Selection
- Turn on the welding machine using the power switch.
- The 4.1-inch LED display will illuminate, showing current settings.
- Use the control knobs and buttons to select your desired welding process: SYN MIG, MAN MIG, FLUX MMA, or LIFT TIG.
7.2 Adjusting Parameters
- Synergic Control (SYN MIG): For beginners, simply adjust the amperage or welding wire diameter. The machine will automatically optimize voltage and wire feed speed for flawless results.
- Manual Control (MAN MIG, MMA, LIFT TIG): For experienced users, current and voltage can be controlled separately and precisely adjusted.
7.3 2T/4T Settings
The 2T/4T settings allow for manual or automatic control of the welding process:
- 2T (Two-Touch): Keep pressing the torch switch to dispense welding wire; release the switch to stop. Ideal for short welds.
- 4T (Four-Touch): Press the torch switch once to automatically continue dispensing welding wire; press it again to stop. Suitable for longer welds, reducing hand fatigue.
7.4 Material Suitability
The MIG-135Plus is suitable for welding various metal materials, including:
- Metal Cage
- Square Pipe
- Galvanized Sheet
- Mild Steel
- Cast Iron
- Stainless Steel
7.5 Welding Process Demonstration
Watch this video for a visual demonstration of the welding machine in action, showcasing flux-cored, MMA, and Lift TIG welding processes.
8. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Regularly clean the machine's exterior and internal components (if accessible and safe) to prevent dust and debris buildup, which can hinder cooling and performance. Use compressed air for internal cleaning.
- Check Connections: Periodically inspect all electrical connections, including power cables, torch, and ground clamp, for tightness and signs of wear or damage.
- Consumables: Replace worn contact tips, nozzles, and electrodes as needed to maintain weld quality. Ensure the wire feed liner is clean and free of obstructions.
- Storage: Store the machine in a dry, clean environment when not in use.
9. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not power on | No power supply; loose power cable; tripped circuit breaker | Check power outlet and cable; reset circuit breaker |
| No arc/poor arc starting | Loose ground clamp; incorrect settings; worn electrode/contact tip; dirty workpiece | Ensure good ground connection; verify settings; replace consumables; clean workpiece |
| Wire feed issues (MIG) | Tangled wire; clogged liner; incorrect tension; worn drive roller | Untangle wire; clean/replace liner; adjust tension; inspect/replace drive roller |
| Overheating protection activated | Exceeded duty cycle; poor ventilation | Allow machine to cool down; ensure adequate airflow around the machine |
10. User Tips
- Start with Synergic Mode: If you are new to welding, begin with the SYN MIG mode. It simplifies parameter setup, allowing you to focus on technique.
- Practice on Scrap Metal: Before working on your actual project, practice on similar scrap metal to fine-tune your settings and technique.
- Clean Your Workpiece: Always ensure your workpiece is clean and free of rust, paint, or oil for the best weld quality.
- Proper Ventilation: Even with gasless flux-cored wire, ensure good ventilation to disperse welding fumes.
- Check Consumables: Keep spare contact tips and nozzles on hand, as they are wear items and affect weld quality.
11. Warranty and Support
The ANDELI MIG-135Plus welding machine typically comes with a manufacturer's warranty. Please refer to your purchase documentation or contact your retailer for specific warranty terms and conditions. For technical support or service inquiries, please contact the ANDELI customer service department or your authorized service center.