FLY WING H1 Pro

Contents

Fly Wing H1 Pro Flight Control System User Manual

Model: H1 Pro | Brand: FLY WING

1. Introduction

1.1 Functional Overview

The H1 Pro is the second-generation cost-effective flight control system in the Flywing H series. It features a built-in suspended independent IMU and supports external dual GNSS modules. Utilizing new-generation control and IMU algorithms, it offers a stable experience and broad compatibility.

The H1 Pro Control System comprises a main controller (with built-in suspended IMU, barometer, and compass), a serial GNSS module, and a CAN protocol GNSS-Compass module (equipped with a high-brightness LED indicator light).

1.2 System Composition and Working Principle

The main controller serves as the core module, integrating IMU, barometer, GNSS, and compass modules to achieve precise altitude control and high-accuracy positioning. It supports multiple helicopter configurations (H3, HR3) and the GNSS module is compatible with Beidou, GPS, GLONASS, and GALILEO. The H1 Pro parameter tuning software is used to configure the main controller's parameters, including installation, adjustment, and sensor calibration.

Fly Wing H1 Pro Autopilot System packaging and main components
Figure 1: H1 Pro Autopilot System packaging and main components.
H1 Pro main controller unit close-up
Figure 2: H1 Pro main controller unit.

2. Description of Components and Ports

2.1 Main Controller Features

  • Built-in CAN bus interface and serial port for GNSS backup. The CAN port connects to the GNSS-Compass module.
  • Integrated IMU and barometer for flight posture and altitude measurement, working with GNSS for horizontal positioning.
  • RCIN port supports multiple receiver types: S-BUS/PPM/i-BUS/WBUS/SUMD, and DSM2/DSMX via external adapter. ELRS port supports ELRS receivers.
  • Supports external BEC (6V-13V) or a 2S lithium battery for powering the system (including servos) when using an ESC without BEC.
  • LEFT/RIGHT/BACK ports connect to swash plate servos; TAIL port connects to tail lock actuator (supports 1520us / 760us servo or PWM brushless ESC); ESC port connects to PWM main brushless ESC. AUX port is currently not functional.

2.2 Port Description of Master Controller

H1 Pro specialized socket with fool-proof design
Figure 3: H1 Pro specialized socket with fool-proof design and wider spacing for secure servo connections. Supports up to 12V servos (requires BEC support for 12V output).
  1. Input/Output Interface
  2. CAN Bus Interface
  3. UART serial
  4. USB-C flight controller adjust port
  5. LED flight control status indicator light
  6. 3S/4S/6S/12S lipo battery voltage detection

3. Installation

Please read this section carefully and follow the steps to install and set up your flight control system correctly.

3.1 Installation Process Overview

  1. Ensure all required modules for installation are complete.
  2. Watch instructional videos on www.Flywingrc.com for installation demonstration and module connection.
  3. Watch the software tuning video, run the tuning software, and complete parameter settings.
  4. Check motor/ESC settings, transmitter channel settings, and protection functions.
  5. Confirm all devices connected to the main controller are set up correctly.
H1 Pro package contents: FC, CAN GNSS Module, GNSS fixed base, and wire package
Figure 4: H1 Pro package contents including Flight Controller (FC), CAN GNSS Module, GNSS fixed base, and wire package.

3.2 Installation Preparation (Relevant Equipment)

You will need to prepare the helicopter, transmitter system, ESC, battery, and other equipment. Supported device types include:

  • Supported Helicopter Type: H3 Swashplate Aileronless Helicopter; HR3 Swashplate Aileronless Helicopter.
  • Receiver Type: Supports various types of receivers (S-BUS, DSM2/DSMX, PPM, i-BUS/WBUS/SUMD, ELRS). Ensure successful binding with the transmitter.
H1 Pro Swashplate configuration support (H3 and HR3 diagrams)
Figure 5: H1 Pro supports H3 and HR3 Flybarless helicopter swashplate configurations.

3.3 Starting Installation

Strictly follow installation requirements and parameter settings to prevent flight issues or safety accidents.

3.3.1 Installing Main Controller

Install the main controller facing up and parallel to the fuselage. Ensure the arrow mark points to the front of the helicopter. Position the flight controller as close to the helicopter's center of gravity (main shaft) as possible, then secure it with double-sided tape.

  • Keep it facing up; do not invert it.
  • For severe conditions, ensure proper protection.
  • Install in a low-vibration position, parallel to the fuselage, near the center of gravity.
  • The flight control system is not waterproof, oil-proof, nor dust-proof. Regularly check double-sided tape security.

3.3.2 Installing GNSS-Compass (GPS) Module

Install the GNSS-Compass module according to the following requirements:

  1. Fix the CAN-GNSS-Compass to the GPS mounting base with double-sided tape, keeping it level with the flight controller, then fix them on the tail boom.
  2. If a backup UART-GNSS is needed, fix it to the GPS mount with double-sided tape, keep it level with the flight controller, and fix it on the tail boom. Both GPS modules can be installed in any order.
H1 Pro with Industrial-Grade CAN GPS module
Figure 6: H1 Pro equipped with an Industrial-Grade CAN GPS module, featuring a high-performance M9N Ublox Chip for stable and anti-interference positioning.

4. Connection of Flight Control System

Connect the receiver, ESC, servos, and battery to the H1 Pro and set parameters using the H1 Pro Assistant. Incorrect connections or settings can lead to flight failure or safety hazards.

4.1 Use Requirements

  • Ensure the Flywing mark faces up and the arrow points towards the helicopter nose.
  • Keep surroundings free of tall buildings and trees to avoid affecting GNSS-Compass module performance.
  • Keep the compass at least 15cm away from strong magnetic/electric fields (servos/motors) to prevent flight anomalies.
  • Choose an appropriate GPS installation position to avoid compass interference.
  • Ensure no compass interference warning during operation and no dipping during flight.

4.2 Wiring Diagram

H1 Pro main controller with features listed (Wireless Calibration, Coordinated Turn, Three flight sensitivities mode, Soft Take-off/Land)
Figure 7: H1 Pro main controller highlighting key features and connections.

Warning: The metal shell of H1 PRO is GND. Do not connect the power supply on H1 PRO or on the carbon plate in contact with H1 PRO.

4.3 Receiver Connection

Except for DSM2/DSM receivers, other receivers connect to the RC IN port. DSM receivers require an additional adapter cable. ELRS receivers connect to the side ELRS port.

4.4 Main ESC Connection

Set the ESC to helicopter mode (other parameters can be default). Insert the ESC PWM throttle line into the ESC port (signal line facing up). The ESC must support constant speed and soft start functions.

4.5 Swashplate/Tail Rotor (H3/HR3)

Swashplate supports PWM protocol wide-frequency servos (1000-2000 us, neutral 1520us). Servo voltage depends on ESC BEC voltage. The tail supports 1520us servo / 760us servo / tail motor. Tail ESC PWM range: 1000-2000us.

Swashplate configuration diagrams (H3 and HR3)
Figure 8: Diagrams for H3 and HR3 Swashplate configurations.

4.6 Battery Voltage Detection

The flight control supports voltage detection for 3S/4S/6S/12S batteries. Connect the detection line in parallel with the helicopter's main power supply to the voltage detection port on the side of the flight control.

H1 Pro voltage detection port supporting up to 12S batteries
Figure 9: H1 Pro voltage detection port, upgraded to support a maximum voltage input of 51V at 12S.

5. Setting and Calibration of Flight Control System

Follow the software guidelines and embedded instructions to complete the parameter setting process.

5.1 Software Home Page

The software home page displays the current flight control version, total flight duration, and error warnings. It includes page switching buttons for Radio, Rotor, Tail, and Parameters. Real-time attitude, heading angle, satellite number, and accuracy are shown, along with channel values, travel calibration, and language settings.

5.2 Transmitter Adjustment

The transmitter should not have any MIX. Drone or fixed-wing mode is recommended.

  1. Channel 5 (Flight Mode): Set to a three-position switch: High (GPS mode), Middle (Altitude mode), Low (Acro mode).
  2. Channel 6 (Flight Sensitivities): Set to a three-position switch: High (Sport mode), Middle (Standard mode), Low (Soft mode). This affects head speed and flight sensitivity.
  3. Channel 7 (Motor Switch): Set to a two-position switch: High (start motor), Low (stop motor). Used after flight control is unlocked.
  4. Channel 8 (RTH Mode): Set to a two-position switch: High (return to home), Low (turn off return mode).

Important:

  • After setup, turn off the transmitter and check for "Lost of RC signal" prompt. If present, loss of control return function is normal.
  • If no prompt, check if it's a standard protocol like SBUS. For non-standard protocols, set fail-safe manually.

After channel settings, click "Start Calibration", rotate both joysticks in a circle, and click the button when prompted. Check min/trim/max values for CH1-CH4.

5.3 Setting of Rotor Head

After selecting the helicopter type, choose the correct swashplate type on the rotor head page.

Diagrams illustrating voltage detection support and various helicopter configurations
Figure 10: Voltage detection support for 3S-12S lithium batteries and comparison of flight control features including manual mode and H3/HR3 configurations.

5.4 Tail Setting

Enter the tail setting page, select the correct tail type (1520us tail servo, 760us tail servo, tail Motor), and plug in the signal line of the tail actuator. Adjust the tail pitch ring to its mechanical limits and center using the software sliders.

5.5 Parameters Page

  1. Compass Calibration: See system function page for details.
  2. Low-Battery Return: Recommended to enable. Helicopter automatically returns under low voltage conditions. Supports 3S/4S/6S/12S battery voltage detection.
  3. Other Parameters: Refer to the advanced parameter explanation in the appendix.

5.6 Compass Calibration

Compass calibration is crucial for flight safety. It is easily affected by strong magnetic/electric fields. Frequent calibration ensures optimal performance.

5.6.1 Calibration Precautions

  • Do not calibrate near strong magnetic fields, electric fields, or large metal objects.
  • Do not carry ferromagnetic materials (keys, watches, speakers) during calibration.
  • If calibrated indoors, recalibrate outdoors before flight.
  • Move the helicopter if steel-like substances may affect the compass.

5.6.2 Calibration Steps (Method 1: Use Transmitter)

  1. Quickly switch the transmitter's flight mode switch between GPS mode and Acro mode more than 3 times, ending in GPS mode. The GPS light will flash red, indicating calibration mode.
  2. Flip each side of the helicopter at least 2 times. The GPS status light will change from red to green. When the GPS light turns off, calibration is complete, and the flight control will restart.
  3. During restart, keep the helicopter stationary on the ground for self-test.
Image showing compass calibration on a transmitter
Figure 11: Compass calibrating on transmitter by toggling the mode switch.

5.6.3 Calibration Steps (Method 2: Use Software)

  1. Open the software Parameters page, connect the helicopter battery, click "Start" in the compass calibration module, and follow prompts.
  2. Flip each side of the helicopter at least 2 times. The GPS status light will change from red to green. When the GPS light turns off, calibration is complete, and the flight control will restart.
  3. During restart, keep the helicopter stationary on the ground for self-test.

6. Flight Functions

6.1 Flight Mode

Flywing H1 Pro offers multiple control modes with different flight performances.

  • GPS Positioning Mode: Uses GNSS signals for positioning, enabling automatic positioning at any flight altitude and automatic return to base.
  • Altitude Mode: Provides altitude stabilization without GNSS positioning. Return flight is possible if good GNSS signal was recorded before takeoff.
  • ACRO Mode: Similar to traditional gyroscopes, no fixed height or self-stabilization. Joystick controls angle change speed. Recommended for experienced pilots.
Helicopter flying in GPS Mode + ATT Mode
Figure 12: Helicopter flying in GPS Mode + ATT Mode, offering stabilized flight with minimal intervention.
Helicopter demonstrating 3D Acro mode
Figure 13: Helicopter demonstrating 3D Acro mode, allowing for advanced acrobatic maneuvers.

6.2 Manual Takeoff/Landing

  • Manual Takeoff: Unlock the helicopter by moving joysticks outward. After LED light flashes, release joysticks, turn motor start switch to start. Motor will accelerate slowly. Once stable, push throttle lever up.
  • Manual Landing: Pull down throttle joystick, wait for stable landing, then quickly turn off motor.
Helicopter demonstrating soft takeoff/landing
Figure 14: Helicopter performing a soft takeoff/landing, simulating real helicopter gestures with proportional control.

6.3 Flight Protection

  • One-Click Return: Helicopter automatically returns to the last recorded returning point. Toggle CH8 switch to initiate. Requires good GNSS signal.
  • Return When Out of Control: If wireless signal is lost for >3 seconds (with good GPS signal and compass), helicopter returns to the last recorded point.
  • Low-Battery Return: If battery voltage is below set value for >10 seconds (with good GPS signal and compass), helicopter returns to the last recorded point. Set return voltage reasonably.
Helicopter returning to base with GPS pin, illustrating one-click/low battery return
Figure 15: Helicopter demonstrating one-click/low battery return function, automatically returning to the takeoff point.

6.4 Coordinated Turn

This flight control algorithm technique allows the helicopter to maintain stability and maneuverability during a turn, solving issues like poor coordination and large turning radius. Effective in GPS and attitude modes (not Acro mode).

Helicopter performing a coordinated turn
Figure 16: Helicopter performing a coordinated turn, banking angles for a smaller turning radius.

6.5 Soft Takeoff/Landing

This function allows the flight control to manage vertical speed during takeoff and landing. When altitude reaches 1m, it switches to transmitter scale control. This improves simulation for scale helicopters.

6.6 Flight Restrictions and No-Fly Zones

Helicopters must be flown within designated airspace, complying with International Civil Aviation Organization and local air traffic control regulations. Users are responsible for adhering to local laws and regulations for safe and legal operation.

7. Inspection of Flight Control System

7.1 Hardware Check

  1. Ensure each module is installed correctly and securely.
  2. Verify wiring of electric regulator and receiver is correct and secure.
  3. Check if the mode switch corresponds to the flashing of the status LED indicator.
  4. Confirm the GNSS-Compass working status indicator light is flashing correctly.
  5. Check if sensor parameters are normal and calibration is conducted as prompted.
  6. Shake the helicopter before takeoff to check if it is level and corrections are accurate.
Exploded view of the H1 Pro high-performance sensor
Figure 17: Exploded view of the H1 Pro high-performance sensor, featuring ICM42688P gyroscope, IST8310 compass, and MS5611 gas sensor, with specialized shock-absorbing sponge and copper counterweight.

7.2 Software Inspection

  1. Are the installation parameters of the helicopter set correctly?
  2. Are the installation parameters of the main controller set correctly?
  3. Check whether the voltage protection and fail-safe settings are correct.

8. Flight Safety

8.1 Safety Summary

Flywing recommends enjoying flight in a safe and responsible environment. Users must understand the helicopter and emergency procedures.

8.1.1 Environment

  • Fly in open areas away from crowds, roads, facilities, airports, and obstacles.
  • Understand helicopter performance; high altitude affects battery/power.
  • Operating temperature: -10°C to 55°C (without direct sunlight).
  • Fly in good weather (no rain, wind, extreme weather), during the day or in good lighting.
  • Fly within legal zones.

8.1.2 Inspection

  • Ensure sufficient battery levels.
  • Propellers are undamaged and securely installed.
  • All helicopter parts are clean and intact.
  • Flight control modules are securely installed, not touching other metals/conductive materials. Installation position and orientation are correct. Connections are secure, wires organized.

8.1.3 Operation

  • Do not approach rotating propeller and motor.
  • Fly within visual line of sight.
  • Do not transport hazardous materials.
  • Do not operate helicopter under influence of alcohol or drugs.
  • Return immediately if low battery warning.
  • Helicopter will not automatically avoid obstacles during automatic return flight.
  • After landing, turn off helicopter first, then transmitter.
  • Do not use product to throw or launch items.

8.1.4 Maintenance

  • Regularly check status of each module.
  • Store in a dry environment (5°C ~ 35°C) away from heat, vibrations, strong magnetic/electric fields.
  • Do not store at high places to avoid falls.

8.1.5 Flight Restrictions and Local Regulations

  • Flying is strictly prohibited in no-fly zones.
  • Recommended flight altitude below 120m. Comply with local laws.

9. Technical Specifications

Table of H1 Pro technical specifications
Figure 18: Detailed technical specifications for the H1 Pro Flight Control System.
AttributeSpecification
Helicopter typeHR3/H3 Aileronless Swashplate
Battery type3S, 4S, 6S, 12S lithium polymer battery
Receiver typeS-BUS / PPM / i-BUS / WBUS / SUMD/ELRS; DSM2/DSMX (adapter needed)
Supporting PCWin10, Win11 (64-bit)
Rated power2W
Voltage input range6V-13V, ESC BEC power supply
Ambient temperature-10°C to 55°C
Dimensions (Main FCU)48mm × 31mm × 18.5mm
Dimensions (CAN GPS)47mm × 30mm × 14mm
Dimensions (UART GPS)37mm × 30mm × 13.5mm
Weight (Main FCU)34g
Weight (CAN GPS)33g
Weight (UART GPS)21.5g
Maximum flight angleSoft: 25°; Standard: 35°; Sport: 40°
Hovering accuracy (GPS Mode)Vertical: ± 0.5m, Horizontal: ± 1.5m

10. Troubleshooting

10.1 Common Issues and Solutions

  • Abnormal Compass Data / Helicopter Rotates Slowly: Recalibrate the compass. Ensure calibration is done in an open area away from magnetic interference.
  • Severe Drifting / Inability to Fly Straight / Hovering in Circles: This indicates abnormal compass data or mechanical issues. Recalibrate compass or check helicopter's mechanical structure.
  • Helicopter Porpoising (Wave-like Motion) in High-Speed Flight: Increase Pitch gain.
  • Severe Nodding During Hover: Reduce Pitch gain. If issue persists below 20% gain, check for seized internal bearings or swashplate servo jitter.
  • Severe Left-Right Oscillations During Hover: Reduce Roll gain.
  • Tail Wagging / High-Frequency Vibrations: Slightly increase Tail gain for slight wagging, decrease for high-frequency vibrations. If significant, check for mechanical issues like missing thrust bearing shims.
  • Severe Vertical Oscillations: Reduce AltHold gain. If issue persists below 20% gain, check for mechanical fault or stuck bearing in rotor head.
  • "Lost of RC signal" Prompt: Check transmitter fail-safe settings, especially for non-standard protocols.
  • Flight Control System Not Powering On: Ensure battery voltage detection line is correctly connected and power supply is adequate.

11. User Tips

  • Exploring 3D Flight: The H1 Pro supports 3D Acro mode, allowing for advanced maneuvers like flying upside down and sideways. Ensure you are proficient with basic flight modes before attempting 3D flight.
  • Compass Calibration Location: Always perform compass calibration in an open, interference-free environment. Avoid areas with strong magnetic fields, metal structures, or indoors if possible.
  • Software Tuning: Utilize the H1 Pro Assistant software for precise parameter tuning. Watch the official instructional videos for guidance on installation and tuning.
  • Pre-Flight Checks: Before each flight, perform a thorough hardware and software inspection to ensure all components are secure, connections are correct, and settings are optimal.

12. Warranty and Support

For the latest instructions, warnings, and updates to this disclaimer, please visit the official Flywing website: www.flywingrc.com.

This manual is subject to updating without notice. You can query the latest version of the "User Manual" on the official FLYWING website.

A detailed user manual in PDF format is also available for download: H1 Pro User Manual (PDF).

If you have any comments or suggestions, you can leave a message on the official website.

FLYWING All Rights Reserved.

13. Appendix

13.1 LED Flight Status Indicator

ModeH2 LED StatusGPS LED StatusContent
GPS mode--- ------ ---Locked, searching for satellite positioning
--- ------ ---Main GPS satellite positioning completed, unlocking available.
--- ------ ---Dual GPS satellite positioning completed, unlocking available.
--- ------ ---Unlock status
--- ------ ---Abnormal battery voltage
Attitude/ Intelligent trick mode--- ------ ---Locked, searching for satellite positioning
--- ------ ---Main GPS satellite positioning completed unlocking available.
--- ------ ---Dual GPS satellite positioning completed unlocking available.
--- ------ ---Unlock status
--- ------ ---Abnormal battery voltage
Return mode--- ------ ---RTL Return Flight Mode
Compass calibration--- ------ ---Calibration progress: 0-25%
--- ------ ---Calibration progress: 25-50%
--- ------ ---Calibration progress: 50-75%
--- ------ ---Calibration progress: 75-99%
--- ------ ---Calibration completed
Fault status--- ------ ---Abnormal acceleration
--- ------ ---Compass malfunction
--- ------ ---Remote control malfunction
--- ------ ---Other faults

13.2 LED Flashing Speed Explanation

  • Slow flashing: Once every half second or so.
  • Fast flashing: Once every quarter of a second or so.
  • Rapid flashing: Very fast flashing.
  • Normally on: Solid light.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.