1. Important Safety Information
WARNING: Please read and understand all safety information before installation and operation.
- Mind potential fire risk and strictly follow the instruction manual for charging and storage.
- While using the product, always wear protective equipment and fully comply with applicable laws and regulations.
- Do not operate in rainy weather or on slippery surfaces.
- Avoid overloading; ensure the load remains within the safe operating range.
- Before use, inspect all accessories to confirm they are securely installed.
2. Product Overview
The Flipsky FSESC75200 is a high-current Electronic Speed Controller (ESC) designed for demanding applications such as e-foils, fighting robots, surfboards, and AGV robots. It features an aluminum PCB for efficient heat dissipation and supports a wide voltage range.
3. Specifications
| Feature | Detail |
|---|---|
| Firmware | 5.2 (supports firmware upgrade) |
| Voltage Range | 14-84V (safe for 4-20S battery configurations) |
| Continuous Current | 50V/200A; 75V/150A (dependent on mounting, ambient temperature, and air/water circulation) |
| Burst Current | 300A |
| BEC Output | 5V@1A |
| Supported Modes | DC, BLDC, FOC (sinusoidal) |
| ERPM | 150000 |
| Communication Ports | USB, CAN, UART, SPI, IIC |
| Supported Sensors | ABI, HALL, AS5047, AS5048A |
| Input Source Support | PPM, ADC, NRF, UART |
| Sensorless Support | Yes |
| Regenerative Capacity | Yes |
| Programmable | Via VESC_TOOL |
| Dimensions | 130 x 67.7 x 40.1 mm (Including aluminum case) |
| Motor/Power Wire Size | 8 AWG |
| Material | Composite Material |
| Origin | Mainland China |
| Recommended Age | 14+ years |
| Use | Vehicles & Remote Control Toys |
Key Features:
- Adjustable protection against: low voltage, high voltage, over current, temperature abnormal, MOSFETs/motor over temperature.
- Supports various control modes: Current, Duty cycle, Speed, PID control modes.
- Supports balancing car function by connecting an IMU module through the IIC interface (e.g., MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160).
- Equipped with CPU: 32F405 with frequency 168MHz.
- Aluminum PCB for good heat dissipation and extended lifespan.
- Two COMM ports: UART Bluetooth module, screen display, or remote controller supportable.
4. Setup and Installation
Follow these steps carefully for proper installation of your FSESC75200.
- Power Off: Always turn off the power to your system before beginning any installation.
- Wiring: Connect the ESC according to the wiring diagram provided below. Ensure all connections are secure and correctly oriented.
- Initial Test: After installation, perform a thorough test of all functions to verify normal operation before full use.
Wiring Diagram:
Port Legend:
- 1. USB: For VESC_TOOL connection and firmware updates.
- 2. PPM: Pulse Position Modulation input for remote control.
- 3. CAN: Controller Area Network for multi-ESC communication.
- 4. UART2: Universal Asynchronous Receiver/Transmitter for external modules (e.g., Bluetooth).
- 5. SWD: Serial Wire Debug for advanced debugging.
- 6. COMM: Communication port.
- 7. HALL: Hall sensor input for motor position feedback.
Important: When disconnecting wires, please press the release tab on the connectors. Do not pull directly on the wires or connectors to avoid damage.
5. Operating Instructions
Once the FSESC75200 is correctly installed and configured via VESC_TOOL, it is ready for operation. The ESC supports various control modes (Current, Duty Cycle, Speed, PID) which can be selected and fine-tuned using the VESC_TOOL software according to your application's requirements.
Ensure your motor and battery are compatible with the ESC's specifications (voltage, current limits) to prevent damage and ensure safe operation.
6. Maintenance
Proper maintenance ensures the longevity and reliable performance of your FSESC75200.
- Do not disassemble accessories arbitrarily. Unauthorized disassembly may void warranty and cause damage.
- Store the ESC away from high temperatures, direct sunlight, and humid environments.
- When not in use for extended periods, disconnect power from the ESC and store it properly in a dry, cool place.
- Regularly inspect all wiring and connectors for signs of wear, corrosion, or loose connections.
7. Troubleshooting
If you encounter issues with your FSESC75200, refer to the following common troubleshooting steps:
- Instability after installation: Verify that all latches and connectors are fully engaged and seated correctly.
- Abnormal functionality: Reconnect all cables by unplugging and reinserting them firmly. Sometimes a simple reseat can resolve connectivity issues.
- Inability to secure firmly: Adjust screws to the appropriate tightness. Do not overtighten, as this can damage components or the housing.
- ESC not responding: Check power supply, battery voltage, and all connections. Ensure the VESC_TOOL software is correctly configured and firmware is up to date.
8. User Tips
To ensure optimal performance and avoid potential issues, consider the following tips:
- Phase Filtering: Phase filtering is NOT available for Flipsky ESC75100 and 75200.
- Firmware Configuration: When using firmware version 5.3 or above (VESC_TOOL 3.01), you MUST turn off the phase filter function and choose "false" in VESC_TOOL. Failure to do so will result in ESC damage.
- Default Parameters: Avoid restoring default parameters when using the wizard interface in VESC_TOOL, especially after making specific configurations related to phase filtering.
- Cooling: While the ESC has an aluminum PCB for heat dissipation, ensure adequate airflow or consider additional cooling solutions for high-current, continuous operation to maintain optimal performance and lifespan.
For more detailed instructions and advanced configurations, please refer to the official Flipsky VESC_TOOL documentation or the User Manual (PDF).
9. Warranty and Support
For warranty claims, technical support, or service inquiries, please contact the seller or Flipsky customer service directly. Keep your purchase receipt as proof of purchase.
Please note that unauthorized modifications or improper use of the product may void the warranty.