SONICAKE QPB-30/QPB-31 Guitar Pedalboard User Manual

1. Introduction

The SONICAKE QPB-30/QPB-31 is a meticulously designed, compact, and lightweight pedalboard crafted from aerospace-grade aluminum alloy. It provides an organized and stable platform for your guitar effect pedals, ensuring a clean and streamlined setup. The QPB-31 variant includes a high-quality carry bag for enhanced portability and protection.

This manual provides essential information for setting up, operating, and maintaining your SONICAKE pedalboard.

2. Package Contents

Please check the contents of your package upon arrival. Depending on your chosen model, you will receive the following:

• QPB-30 (Pedalboard Only):
  • 1 x SONICAKE Pedalboard
  • 4 x Pedal Mounting Tapes
  • 10 x Zip Ties
  • 1 x Screwdriver
• QPB-31 (Pedalboard with Bag):
  • 1 x High-Quality Carry Bag
  • 1 x SONICAKE Pedalboard
  • 4 x Pedal Mounting Tapes
  • 10 x Zip Ties

3. Specifications

4. Setup Guide

The SONICAKE pedalboard is designed for easy setup, allowing you to quickly organize your effect pedals.

1. Prepare Your Pedals and Board:

   Ensure your pedals are clean and free of dust. Place the pedalboard on a stable, flat surface.

2. Attach Mounting Tapes:

   Apply the provided pedal mounting tapes (hook and loop fasteners) to the bottom of your effect pedals and the surface of the pedalboard. Ensure a firm press for good adhesion.

3. Arrange Pedals:

   Carefully place your pedals on the board in your desired signal chain order. The compact design allows for 8-10 mini pedals. The angled surface and non-slip foot pads ensure stability.

   

4. Cable Management:

   Utilize the hollow-carved design of the pedalboard for efficient cable routing. Use the included zip ties to secure power and patch cables neatly underneath the board, preventing clutter and accidental disconnections.

5. Connect Your Gear:

   Connect your guitar to the input of your first pedal and the output of your last pedal to your amplifier. Connect power to each pedal as required.

5. Operation

Once your pedals are securely mounted and connected, your pedalboard is ready for use. The ergonomic design with a comfortable angled surface makes accessing and operating your pedals straightforward.

• Stability: The four dedicated non-slip foot pads provide rock-solid stability during performance, preventing the board from sliding.
• Portability (QPB-30): The movable handle allows for easy transport. It can be adjusted up or down without interfering with cable management.
• Portability (QPB-31): For the QPB-31 model, place the assembled pedalboard into the high-quality carry bag. The bag features a shoulder strap, convenient side pocket for cables, and a comfortable handle for easy carrying.

6. Maintenance

To ensure the longevity and optimal performance of your SONICAKE pedalboard, follow these maintenance guidelines:

• Cleaning the Pedalboard: Wipe the pedalboard surface with a soft, dry cloth to remove dust and debris. For stubborn marks, a slightly damp cloth can be used, followed by immediate drying. Avoid abrasive cleaners or solvents.
• Inspecting Mounting Tapes: Periodically check the adhesion of the pedal mounting tapes. If they lose their stickiness, replace them to ensure pedals remain secure.
• Cable Inspection: Regularly inspect all patch and power cables for any signs of wear, fraying, or damage. Replace damaged cables immediately to prevent signal loss or electrical issues.
• Carry Bag Care (QPB-31): If your model includes the carry bag, clean it with a damp cloth and mild soap if necessary. Allow it to air dry completely. Store the bag in a cool, dry place when not in use.
• Storage: When not in use, store the pedalboard in a dry environment, ideally in its carry bag (if applicable), to protect it from dust and potential damage.

7. Troubleshooting

Here are some common issues and their solutions:

Issue: Pedals are not staying securely on the board.

Solution: Ensure both sides of the mounting tape (hook and loop) are firmly attached to the pedal and the pedalboard. Press down firmly on the pedals after placement. If the tapes are old or worn, replace them with new ones.

Issue: Pedalboard slides during use.

Solution: Verify that the non-slip foot pads are clean and intact. Ensure the pedalboard is placed on a stable, non-slippery surface. Avoid placing it on very smooth or uneven floors.

Issue: Cables are messy or getting tangled.

Solution: Re-route your cables using the hollow-carved design underneath the board. Use the provided zip ties to bundle and secure cables, keeping them tidy and out of the way.

8. User Tips

• Plan Your Layout: Before applying tapes, arrange your pedals on the board to find the most ergonomic and efficient layout for your playing style. Consider signal flow and power cable access.
• Cable Lengths: Use patch cables of appropriate lengths to minimize clutter. Shorter cables between closely spaced pedals can significantly improve tidiness.
• Power Supply Placement: Many users mount their power supply underneath the pedalboard to save space and keep the top surface clean. The hollow design of the SONICAKE board facilitates this.
• Secure Excess Cable: After connecting all pedals, use the zip ties to secure any excess cable length, especially power cables, to prevent accidental disconnections or tripping hazards.
• Regular Cleaning: A quick wipe-down after each use can prevent dust and grime buildup, keeping your setup looking professional.

9. Warranty & Support

For any questions, technical support, or warranty inquiries regarding your SONICAKE QPB-30/QPB-31 pedalboard, please contact the seller or manufacturer directly through their official channels. Keep your purchase receipt as proof of purchase.