LAUNCH X-431 Creader TPMS 5011 V2

Contents

LAUNCH X431 Creader TPMS 5011 V2 User Manual

Model: X-431 Creader TPMS 5011 V2

Brand: LAUNCH

1. Introduction

The Smart TPMS Diagnostic System, developed by LAUNCH, is designed to trigger, program, and relearn TPMS sensors, as well as perform TPMS diagnostics. It also supports sensor OE number lookup and all 10 modes of OBD II testing for comprehensive vehicle diagnosis. This tool offers coding, reset, relearn, and other service functions to restore vehicles to functional status after repair or replacement.

This tool is specifically designed to work with all OBD II compliant vehicles. To verify if a vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label, usually located under the hood or by the radiator. An OBD II compliant vehicle will have a label designating “OBD II Certified”. Government regulations mandate that all OBD II compliant vehicles must have a standard 16-pin Data Link Connector (DLC).

LAUNCH X431 Creader TPMS 5011 V2 device with four TPMS sensors
The LAUNCH X431 Creader TPMS 5011 V2 diagnostic tool shown with four accompanying TPMS sensors.

2. Safety Information

2.1 General Safety Precautions

  • This product is not a toy. Do not allow children to play with or near this item.
  • Do not expose the device to rain or wet conditions.
  • Do not place the device on any unstable surface.
  • Never leave the device unattended during the charging process. The device must be placed on a non-flammable surface during charging.
  • Handle the device with care. If the device is dropped, check for breakage and any other conditions that may affect its operation.
  • Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
  • Keep the tool dry, clean, free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the device when necessary.
  • People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to a heart pacemaker could cause pacemaker interference or pacemaker failure.
  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, test equipment, etc., away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs. These components create hazardous voltages when the engine is running.
  • Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Don't connect or disconnect any test equipment while the ignition is on or the engine is running.

2.2 Battery Safety

  • This tool contains an internal Lithium Polymer battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, pierce, or dispose of the battery in fire or water.

2.3 Compliance Information

FCC ID: XUJCRT511SV2

IC: 29886-CRT511SV2

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

RF Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The SAR limit adopted by USA and Canada is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The highest SAR value reported to the Federal Communications Commission (FCC) and Industry Canada (IC) for this device type when it is tested for proper body-worn use is under 1g 1.6W/Kg.

This device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The RF frequencies can be used in Europe without restriction.

3. Product Overview

3.1 Components & Controls

Diagram of the LAUNCH X431 Creader TPMS 5011 V2 device with numbered components.
Front view of the LAUNCH X431 Creader TPMS 5011 V2, highlighting its main components.
  1. Power button: Turns the tool on/off.
  2. Charging port: Used to charge the tool.
  3. Display screen: Shows test results and user interface.
  4. DB-15 diagnostic connector: Connects the tool to the vehicle's Data Link Connector (DLC).
  5. TPMS antenna: Used for TPMS sensor communication.
  6. Settings button: Provides quick access to the Settings module.
  7. HOME button: Navigates to the home (Job Menu) screen.
  8. BACK button: Exits the current program or returns to the previous screen.

3.2 Accessories Included

The following items are typically included in the package:

  • 1 x Creader TPMS 5011 V2 diagnostic unit
  • 1 x Diagnostic Main Cable
  • 1 x Type-C Charging Cable
  • 1 x Quick Start Guide
Contents of the LAUNCH X431 Creader TPMS 5011 V2 box, including the device, diagnostic cable, charging cable, and quick start guide.
The complete package contents for the LAUNCH X431 Creader TPMS 5011 V2.

4. Setup and Initial Use

4.1 Charging and Turning On/Off

There are two methods to charge the tool:

  1. Via PC: Connect one end of the charging cable to the tool's charging port and the other end to a PC or AC outlet with USB ports. Unplug the cable when charging is complete.
  2. Via OBD Diagnostic Port (Not recommended for primary charging): If the tool is properly connected to the vehicle's DLC port, it will be charged automatically. Note that charging via the OBD diagnostic port will consume the vehicle's battery power and is only recommended during OBD diagnosis operations.

To turn the tool on/off, press the Power button for about 3 seconds. To perform a forced shutdown, press the Power button for about 8 seconds.

4.2 Getting Started

For first-time use, follow these steps to configure system settings:

  1. Power on the tool. Tap 'Start' on the welcome page.
  2. Choose the desired system language and tap 'Next'.
  3. Choose the desired time zone and tap 'Next' to enter the WLAN setup screen.
  4. Slide the WLAN switch to 'ON'. The system will search for available wireless LANs. Select your desired network.
    • If the network is open, you can connect directly.
    • If the network is encrypted, enter the security key (network password).
  5. After network connection, tap 'Next Step' to configure workshop information. Input the required details and tap 'Next Step'. It is strongly recommended to fill in a valid email address, as it will be appended to diagnostic reports.
  6. Read the user agreement, check the box to agree to the terms, and tap 'OK' to finish the sign-up process and navigate to the Job Menu.

4.3 Job Menu Overview

The Job Menu includes the following function modules:

ModuleDescription
TPMSPerforms various TPMS operations, detects sensor data, and key frequency.
ResetPerforms commonly used repair & maintenance services.
OE InquiryInquires the original OE part number of the sensor and checks applicable vehicle models.
OBD IIChecks for DTCs, isolates Malfunction Indicator Lamp (MIL) causes, checks monitor status, verifies repairs, and performs emission-related services.
UpgradeUpdates diagnostic software and APK.
DataIncludes DTC library, DLC location, Image viewer, Feedback, FAQ, and User Manual.
SettingsAdjusts tool settings to your particular needs.
Screenshot of the LAUNCH X431 Creader TPMS 5011 V2 showing the main menu with icons for TPMS, Reset, OE Inquiry, OBD II, Upgrade, Data, and Settings.
The main Job Menu interface of the diagnostic tool.

4.4 Settings Configuration

  • Units of measurement: Set to Metric System or English System.
  • Firmware Fix: Fixes and repairs tire pressure firmware and VCI firmware.
  • Display/Brightness: Adjusts standby time and screen brightness. Reducing brightness conserves power.
  • Sound: Adjusts volume and other sound settings.
  • Network: Manages WLAN connection. The tool has a built-in WLAN module for online access, tool registration, and software updates. Turn off WLAN when not in use to conserve battery.
  • Time Zone: Sets the device's time zone.
  • Language: Supports multiple languages (Germany, Britain, West, France, South Korea, Italy, Japan, Traditional Chinese, Portuguese, Russia, Arabic).
  • Region (TPMS): Sets the target region for TPMS sensor application.
  • Workshop information: Adds a personalized tag to diagnostic reports.

5. TPMS Operations

The LAUNCH X431 Creader TPMS 5011 V2 is a professional tool for comprehensive TPMS diagnosis, activation, programming, and relearning.

Diagram showing the LAUNCH Creader TPMS 5011 V2 device next to a car tire, listing TPMS functions: 315/433MHz sensor support, 99% vehicle coverage, check sensor, activate TPMS sensor, TPMS diagnose, relearn TPMS sensor, check OE number, read & write sensor ID, turn off TPMS warning light, and 11 languages support.
Overview of TPMS functions supported by the LAUNCH Creader TPMS 5011 V2.

5.1 Detect Sensor & Key

  • Detect Sensor: Checks information of LAUNCH-specific sensors.
  • Detect Key: Detects the frequency of wireless vehicle keys.

5.2 TPMS Operations Flow

For initial use, follow this general flow:

  1. Enter TPMS module.
  2. Select vehicle manufacturer.
  3. Select vehicle model.
  4. Select vehicle year.
  5. Select the desired TPMS function.

Note: For indirect TPMS vehicles, only the Relearning function is supported. For vehicles using Direct TPMS, functions generally include Activation, Programming, and Relearning. Available TPMS functions may vary by vehicle.

5.3 Activate Sensor

This function allows you to activate TPMS sensors to view data such as sensor ID, tire pressure, tire frequency, tire temperature, and battery condition.

  1. Tap the 'Activate' tab on the screen.
  2. For universal sensors, place the TPMS antenna alongside the valve stem, point towards the sensor, and tap 'Activate' on the screen.

Notes:

  • For early magnet-activated sensors, place the magnet over the stem, then place the tool alongside the valve stem.
  • If the TPMS sensor requires tire deflation (e.g., 10PSI), deflate the tire and place the tool alongside the stem while tapping 'Activate'.
  • The tool performs TPMS tests in sequence: Front Left (FL), Front Right (FR), Rear Right (RR), Rear Left (LR), and SPARE (if applicable).
  • Abnormal sensor data will be displayed in red.

After successful activation, the tool will beep, and sensor data will be displayed. If you need to read the original sensor ID from the ECU, connect the tool to the vehicle's DLC via the diagnostic cable and tap 'Read ECU ID'.

The LAUNCH Creader TPMS 5011 V2 activating a TPMS sensor on a car tire, with a screen showing 'Activate TPMS Sensors' and listing features like tire temperature, tire pressure, battery condition, and sensor ID.
Activating TPMS sensors and viewing real-time data.

5.4 Program Sensor

This function allows programming sensor data to LAUNCH-specific sensors, replacing faulty or non-functioning sensors. It supports unlimited repeated programming.

Screenshot of the LAUNCH X431 Creader TPMS 5011 V2 programming screen, showing options for 'Auto Create', 'Manual Create', 'Copy ID by Activation', and 'Copy ID by OBD'. A car diagram with a sensor is also visible.
Programming TPMS sensors with various methods.

Available programming options:

  • Auto Create: Programs a LAUNCH-specific sensor with a random ID generated based on the test vehicle. Select the wheel, place the LAUNCH sensor near the TPMS antenna, and tap 'Auto'. Then tap 'Programming' to write the new ID.
  • Manual Input: Manually enter a random or original sensor ID using the on-screen keypad. Select the wheel, place the LAUNCH sensor near the TPMS antenna, and tap 'Programming' to write the new ID.
  • Copy by Activation: Writes retrieved original sensor data to a LAUNCH-specific sensor after the original sensor has been triggered. Select the wheel position, tap 'Copy by Activation', and then 'Programming' to write the data.
  • Copy by OBD: Writes saved sensor information to a LAUNCH-specific sensor after performing 'Read ECU ID'. This requires connecting the tool to the vehicle's DLC port. Tap 'Read ECU ID', then 'Programming' to write the copied sensor information.
Diagram illustrating the unlimited repeat programming feature of the LAUNCH Creader TPMS 5011 V2, showing steps: 1. ID Generation Create, 2. Automatic creation, 3. Copy ID. The device is shown next to a car tire.
Unlimited repeat programming for LAUNCH sensors.

5.5 Learning Service (Relearn)

This function provides detailed TPMS sensor relearn procedures. Relearn operations are necessary when newly programmed sensor IDs differ from the original IDs stored in the vehicle's ECU, allowing the ECU to recognize the new sensors.

Diagram showing three TPMS relearn methods: OBD Relearn (write TPMS sensor ID to TPMS module through OBD connector), Automatic Relearn (complete by driving), and Stationary Relearn (placed in the LRARN MODE). The LAUNCH device is shown next to a car tire.
Three methods for TPMS relearning.

The TPMS 5011 V2 offers three relearn methods:

  • OBD Relearn: Writes TPMS sensor IDs to the TPMS module via the OBD connector.
  • Automatic Relearn: Completes the relearn process by driving the vehicle.
  • Stationary Relearn: Performed when the vehicle is placed in 'Learn Mode'.

Learning Process Steps (General):

  1. Install the tire pressure sensor correctly.
  2. Inflate all tires to the nominal value according to the tire label.
  3. Starting from the left front wheel, activate each sensor using the TPMS tool in the order of left front, right front, right rear, left rear, and full-size spare tire (if any).
  4. Turn on the ignition switch (engine off).
  5. Connect the TPMS tool to the OBDII interface and write the sensor ID using the sensor learning function.
  6. Hold the ignition switch in the ON position and reactivate the sensor inside the tire.
  7. Switch off the ignition and switch on the ignition again.
  8. Conduct a road test at a speed of 30km/h and above for at least 15 minutes to ensure the tire pressure system works normally.

On-screen buttons during relearning:

  • Read DTC: Reads TPMS diagnostic trouble codes stored in the vehicle's ECU.
  • Clear DTC: Clears existing TPMS diagnostic trouble codes.
  • OBD Relearning: Writes newly programmed sensor IDs into the vehicle's ECU via the vehicle's DLC socket.

5.6 OE Inquiry

This function allows you to check the OE (Original Equipment) number of sensors. Tap 'OE Inquiry' on the Job Menu screen, select the target sensor manufacturer, and then the corresponding OE number to view details.

6. OBD II Diagnostics

This function provides a quick way to check for Diagnostic Trouble Codes (DTCs), identify the cause of the Malfunction Indicator Lamp (MIL), check monitor status for emissions certification, verify repairs, and perform other emission-related services.

Screenshot of the LAUNCH Creader TPMS 5011 V2 showing a grid of full OBDII functions, including Read Codes, O2 Sensor Test, Erase Codes, DTC Lookup, I/M Readiness, Live Data, MIL Fault Indicator Light, Vehicle Information, Freeze Frame, On-Board Monitoring, All OBDII Compliant Vehicles, and EVAP Monitor Test.
Full OBDII diagnostic functions available on the device.

6.1 Connection

  1. Turn the ignition off.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to section 2.3 for possible locations.
  3. Plug one end of the diagnostic cable into the vehicle's DLC port and the other end into the DB-15 diagnostic connector of the tool. Tighten the captive screws.

Notes:

  • Some vehicles may have a plastic DLC cover that needs to be removed.
  • The cable connector is keyed and fits only one way. If you have difficulty, rotate the connector 180 degrees and try again.
  • Turn the ignition on (engine can be off or running).
  • CAUTION: Do not connect or disconnect any test equipment with the ignition on or engine running.
  • The system will automatically turn on and navigate to the main menu screen.

6.2 Start OBD Diagnostics

After connecting the tool, tap 'OBD II' on the Job Menu screen. The tool will automatically check the vehicle's computer to determine the communication protocol and display the Monitor Status.

OBD II Functions:

  • I/M Readiness: Checks if emission-related systems are operating properly and ready for inspection/maintenance testing.
  • Read Live Data: Retrieves and displays real-time ECU/PCM data stream.
  • Read Freeze Frame: Captures a snapshot of operating conditions when an emission-related fault occurs.
  • Read Fault Code (DTCs): Identifies the section of the emission control system that has malfunctioned.
  • Clear Fault Code: Erases codes from the vehicle after repairs. Ensure ignition is ON and engine is OFF before clearing codes.
  • Test Results - On-board monitoring test: Retrieves test results for non-continuously monitored powertrain components and systems.
  • Control Operations of On-board Component/System: Accesses vehicle-specific subsystem and component tests.
  • Read Vehicle Information: Displays VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number).

7. Reset Functions

The tool offers various reset, relearn, and coding service functions to restore vehicle systems. Available tests vary by vehicle manufacturer, year, and model. Regular updates are recommended to access the latest functions.

Icons representing 12 reset functions: SAS Reset, Brake Reset, Oil Reset, I-M-M-O Reset, Inject Reset, Battery Matching, ABS Bleeding, Throttle Reset, DPF Reset, Sunroof Reset, Seats Calibration, Windows Calibration.
Overview of 12 common reset functions.

There are two methods for resetting operations: Manual Reset and Auto Reset. Auto Reset sends commands from the tool to the vehicle's ECU. Manual Reset guides users through on-screen instructions to select options, enter data, and perform necessary actions.

General Reset Flow:

  1. Select "Reset" from the Job Menu.
  2. Choose the desired service function.
  3. Select the desired car brand.
  4. Select the reset mode (varies by vehicle).
  5. Follow the on-screen instructions to proceed.

Detailed Reset Services:

  • Brake Reset: Resets the brake pad system after replacement of pads or sensors.
  • Oil Lamp Reset: Resets oil life systems after oil and filter changes.
  • Battery Reset: Resets the car battery monitoring unit after battery or sensor replacement.
  • SAS Calibration: Calibrates the steering angle and clears fault records after replacing steering angle position sensors or mechanical components.
  • ABS Bleeding: Bleeds the brake system to restore ABS braking sensitivity.
  • Throttle Reset: Initializes the throttle actuator to its default state.
  • D-P-F Regeneration: Clears particulate matter from the D-P-F filter or replaces D-P-F components.
  • TPMS Service: Quickly searches for tire sensor ID, performs TPMS replacement, and sensor testing.
  • Injector Coding: Codes new fuel injector numbers after installation or replacement.
  • Sunroof Reset: Resets sunroof functions like closing on rainy days, slide/tilt memory, and temperature thresholds.
  • Seat Calibration: Calibrates memory in replaced or repaired seats.
  • Windows Calibration: Performs door window matching to recover ECU initial memory.
A collage of images depicting various service functions: SAS Reset, Brake Reset, Oil Reset, I-M-M-O Reset, Inject Reset, Battery Matching, ABS Bleeding, Throttle Reset, DPF Reset, Sunroof Reset, Seats Calibration, and Windows Calibration.
Visual representation of the 12 service functions.

8. Maintenance and Upgrades

8.1 Software Upgrade

If new software or APK updates are available, a numeric indicator will appear on the 'Upgrade' module in the Job Menu. It is strongly suggested to update regularly to enjoy more functions and better service. A stable network connection is required for upgrades.

To upgrade:

  1. Tap 'Upgrade' on the Job Menu to enter the update center.
  2. Tap 'Select All' to select all diagnostic software. To deselect, tap 'Unselect' and uncheck the box next to the vehicle model.
  3. Tap 'Update' to start downloading. Software packages will install automatically once downloaded.

8.2 Data Management

The 'Data' module provides access to various resources:

  • DTC Library: Retrieves detailed descriptions of DTCs from the local database. Swipe to alter values and tap 'OK' to view definitions.
  • DLC (Data Link Connector): Helps locate the vehicle's DLC.
  • Image: Views and manages all screenshots taken with the tool.
  • Feedback: Sends diagnostic problem feedback for analysis and troubleshooting. Options include Diag. Feedback (for tested vehicles), History Feedback (to view records), and Offline Feedback (for logs that failed to submit).
  • User Manual: The user manual is integrated into the tool for easy reference.
Screenshot of the LAUNCH Creader TPMS 5011 V2 showing a DTC library screen with a search bar and a list of DTCs. Below it, a printer is shown with a diagnostic report being printed, illustrating the report sharing and printing feature.
DTC library and report sharing/printing features.

8.3 Other Settings

  • Recovery: Resets the tool to default factory settings. Warning: This may cause data loss. Proceed with caution.
  • Clean Up: Clears cache files and frees up storage space. The tool will reboot after cleanup.
  • Screen Capture: When enabled, a floating screenshot icon appears. Tap it to capture the current screen. Screenshots are saved under Data -> Image.
  • About: Displays hardware configuration and license agreement information.

9. Troubleshooting (FAQ)

Here are some frequently asked questions and answers related to this tool:

  • Question: System halts when reading data stream. What is the reason?
    Answer: It may be caused by a slackened connector. Turn off the tool, firmly connect the connector, and switch it on again.
  • Question: Screen of main unit flashes at engine ignition start.
    Answer: Caused by electromagnetic disturbance, this is a normal phenomenon.
  • Question: There is no response when communicating with the on-board computer.
    Answer: Confirm proper voltage of power supply, and check if the throttle has been closed, the transmission is in neutral, and the water is at proper temperature.
  • Question: Why are there so many fault codes?
    Answer: Usually, it's caused by poor connection or fault circuit grounding.

9.1 Online Feedback

The tool supports online feedback, allowing users to report vehicle problems directly to LAUNCH for timely resolution and improved repair efficiency.

Screenshot of the LAUNCH Creader TPMS 5011 V2 showing an 'Online Feedback' screen with fields for current and latest software versions, model, year, VIN, and an option to choose a feedback log file.
Online feedback interface for reporting issues.

10. Specifications

FeatureSpecification
Screen5" IPS screen, 1280*720 resolution
Input Voltage9 ~ 18V via OBD diagnostic port / 5V via USB cable
CPU1.3GHz, 4-core processor
RAM2GB
Storage32GB
Operating Temperature32°F~113°F / 0°C~45°C
Storage Temperature-4°F~158°F / -20°C~70°C @ RH60%
Wireless SupportWifi
External Testing CertificationCE
Batteries IncludedYes
Software Version2026 NEW
Hardware Version2026 NEW
Activate Sensors99% 315/433MHz Sensors
TPMS ProgrammingUnlimited Repeat Programming
TPMS Relearn & Read TPMS ECU IDYes
Full OBD FunctionsRead/clear codes, I/M readiness, data stream, freeze frame, O2 sensor test, on-board monitor test, EVAP system test, vehicle info, etc.
Supported Resets12 Resets (brake, oil, battery, SAS, ABS bleeding, throttle, D-P-F regeneration, injector coding, seats calibration, sunroof, windows calibration, etc.)

11. User Tips

  • Keep Software Updated: Regularly check for and install software updates to ensure compatibility with the latest vehicle models and access new features.
  • Ensure Stable Connection: When performing diagnostics or updates, always ensure a secure physical connection to the vehicle's DLC and a stable Wi-Fi connection for online functions.
  • Battery Management: Avoid relying solely on the OBD port for charging, especially during long diagnostic sessions, to prevent draining the vehicle's battery. Use the Type-C charging cable with a PC or AC adapter when possible.
  • Review DTCs Thoroughly: Do not replace parts based solely on DTCs. Always consult the vehicle's service manual for proper testing procedures before making repairs.
  • Backup Data: Utilize the screen capture and data management features to document diagnostic reports and important information for future reference.

12. Warranty and Support

12.1 Warranty

This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.

LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user.

This warranty does not cover any part that has been abused, altered, used for a purpose other than intended, or used in a manner inconsistent with instructions. The exclusive remedy for any defective automotive meter is repair or replacement. LAUNCH shall not be liable for any consequential or incidental damages.

Final determination of defects will be made by LAUNCH in accordance with its established procedures. No agent, employee, or representative of LAUNCH has authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.

12.2 Customer Service

If you have any questions on the operation of the unit, please contact the seller or LAUNCH TECH. CO., LTD:

  • Tel: +86-755-84527891
  • E-mail: overseas.service@cnlaunch.com
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.