1. Introduction
This manual provides essential information for the safe and effective use of your AMBITFUL GM Series Multi-Purpose Air Cushioned Light Stand, model GM280P. Designed for photographers and videographers, this stand offers robust support for various lighting equipment, cameras, and softboxes, featuring an upgraded air cushioning system for enhanced protection.
2. Product Specifications
| Feature | Details |
|---|---|
| Model Number | GM280P |
| Material | Aluminum alloy |
| Folded Length | 94 CM |
| Max Extended Length | 280 CM |
| Height Adjustable | 108-280 CM |
| Max Load Capacity | 10 KG |
| Net Weight | 1.95 KG |
| Interface | 1/4" & 3/8" Screw (Universal) |
| Features | Upgraded Air Cushioning, Thickened Aluminium Alloy, Innovative Push Flip Lock, More Stable Base, Non-slip Foot Mats |
| Configured For | Photographic Lighting, Cameras, Softbox |


3. Setup Instructions
- Unfolding the Stand: Gently spread the legs of the light stand until they are fully extended and stable. Ensure the base is firm and secure.
- Adjusting Height: Loosen the flip locks on each section of the stand. Extend the desired sections to achieve the required height. Securely fasten the flip locks to prevent accidental collapse. The stand features an upgraded air cushioning system for slow, controlled lowering, protecting your equipment.
- Attaching Equipment: The top of the stand features a universal 1/4" and 3/8" screw interface. Attach your COB light, LED panel light, camera, or softbox to this interface. Ensure the equipment is securely tightened.
- Final Check: Before use, always double-check that all locks are securely fastened and the stand is stable on a flat surface.


4. Operating Instructions
- Before First Use: Remove any protective films or packaging materials from the light stand.
- Height Adjustment: To adjust the height, release the flip locks on the telescopic sections. Carefully extend or retract the sections to the desired height. The air cushioning system will ensure a smooth and controlled descent when lowering. Once the desired height is reached, firmly close all flip locks.
- Equipment Mounting: Ensure your lighting equipment or camera is compatible with 1/4" or 3/8" screw mounts. Attach the equipment to the top stud of the light stand and tighten it securely.
- Positioning: Adjust the angle and position of your mounted equipment as needed. Always ensure the stand's legs are fully spread for maximum stability, especially when extending to full height or mounting heavy equipment.
- After Use: Carefully lower the stand by releasing the flip locks one section at a time, allowing the air cushioning to work. Fold the legs inward for compact storage.


5. Maintenance & Storage
- Cleaning: Turn off and remove any attached equipment before cleaning. Use a soft, lint-free cloth to wipe down the stand. Do not use abrasive cleaners or solvents.
- Storage: Store the light stand in a dry place at room temperature (15°C - 35°C). Ensure it is clean and dry before storage.
- Long-term Storage: If not used for a long time, ensure the stand is clean and stored in its folded position to prevent damage.

6. Troubleshooting
If the light stand does not function as expected, stop using it and check the following:
- Correct installation or setup: Ensure all sections are properly extended and locked, and the legs are fully spread.
- Compatibility of accessories: Verify that any attached equipment is compatible with the 1/4" or 3/8" screw interface and does not exceed the maximum load capacity of 10kg.
- Stability: Confirm the stand is on a level, stable surface to prevent tipping.
7. Disposal & Recycling
- Do not dispose of this product with general household waste. This product contains materials that may require special handling.
- Follow local environmental and waste disposal regulations for proper recycling of aluminum alloy and other components.
8. Safety & Warnings
Important Safety Information
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the light stand out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use (e.g., supporting photographic equipment).
- Inspect the product before each use; do not use if damaged or if any parts are missing or loose.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture, as this can damage the aluminum alloy and internal mechanisms.
- Handle with care to avoid cuts or injuries from sharp edges or pinch points during setup and takedown.
- Do not overload the stand beyond its maximum load capacity of 10kg.
- Ensure the stand is always placed on a stable, level surface.
9. User Tips
No specific user tips are available at this time. Always refer to the setup and operating instructions for optimal performance and safety.
10. Manufacturer & EU Representative Information
- Manufacturer: Shenzhen New Vision Photography Equipment Co., Ltd, No.5, Guansheng 2nd Road, Luhu Community, Guanhu Street 18F, Block A, Jieshun Technology Center, Shenzhen Guangdong 518000 CHINA, Shenzhen Guangdong Province.
- Manufacturer Email: ambitful999@163.com
- Manufacturer Tel: +86 17603004256
- EU Authorized Representative: E-CrossStu GmbH, 69 Mainzer Landstrasse, Frankfurt am Main, Hessen.
- EU Representative Email: E-CrossStu@web.de
- Importer: Shenzhen New Vision Photography Equipment Co., Ltd
11. Compliance Information
This product complies with applicable safety and regulatory requirements. For electrical or electronic products, conformity marking (e.g., CE) and related documentation may be required, ensuring adherence to electrical safety, electromagnetic compatibility, and environmental compliance standards.
A PDF version of this user manual is available for download: User Manual (PDF)