Introduction
This manual provides comprehensive instructions for the proper installation, operation, and maintenance of your SCULPFUN S30 Pro Max replacement laser lenses. These official original lenses are specifically designed for SCULPFUN S30 Pro Max, Ultra-22W, and Ultra-33W laser modules, ensuring optimal performance and longevity. The lenses feature a reinforced surface for anti-oil and anti-smoke properties, along with high transparency to minimize laser energy loss.

Setup and Installation
The SCULPFUN S30 Pro Max lenses are designed for easy replacement. Please follow these steps carefully. Note: The laser module is not included in the lens package.

- Disassemble Set Screws: Carefully remove the set screws securing the gas nozzle.
- Twist Gas Nozzle: Twist the gas nozzle vertically to detach it.
- Disassemble Lenses: Use tweezers to push the small pit and carefully remove the old lens.
- Clean Lens: If the lens is merely dirty, use alcohol to clean it. If it is damaged, proceed with replacement.
- Install New Lens: Place the new lens into position.
- Tighten with Tweezers: Gently tighten the lens using tweezers.
- Check Seal Ring: Verify the level and proper seating of the seal ring.
- Re-attach Gas Nozzle: Twist the gas nozzle vertically back into place. There is no need to overtighten; stop when you feel it touch the sealing ring. Continue twisting until the bending tube faces right.
- Tighten Set Screws: Secure the gas nozzle by tightening the set screws.
Operating Principles
The SCULPFUN S30 Pro Max lenses are engineered for high performance in laser cutting and engraving applications. Their ultra-high transmittance material ensures minimal laser energy loss as the beam passes through, contributing to efficient and powerful operation of your laser module.

Maintenance
Regular maintenance of your laser lens is crucial for maintaining optimal laser performance and extending its lifespan. The reinforced surface of these lenses is designed to resist oil and smoke accumulation.
Cleaning
To clean the lens, gently wipe its surface with alcohol. This will restore its smoothness and transparency, effectively removing any accumulated oil fume or debris that could hinder laser performance.
Replacement
If the lens becomes scratched, cracked, or otherwise damaged beyond cleaning, it must be replaced immediately to prevent damage to the laser module and ensure consistent output quality. Refer to the "Setup and Installation" section for detailed replacement steps.

Troubleshooting
If you experience a decrease in laser performance, such as reduced cutting power or engraving quality, consider the following:
- Dirty Lens: The most common cause of performance degradation is a dirty lens. Clean the lens thoroughly with alcohol as described in the Maintenance section.
- Damaged Lens: Inspect the lens for any visible damage like scratches or cracks. A damaged lens will scatter the laser beam and must be replaced.
- Improper Installation: Ensure the lens and sealing ring are correctly seated and the gas nozzle is properly secured as per the installation steps.
Specifications
| Feature | Detail |
|---|---|
| Compatibility | SCULPFUN S30 Pro Max, Ultra-22W Laser Module, Ultra-33W Laser Module |
| Quantity per Pack | 6 x SCULPFUN S30 Pro Max Lenses, 6 x Sealing Rings |
| Lens Material | High Transparent Material |
| Surface Treatment | Reinforced, Anti-oil, Anti-smoke |
| Package Size | 12.5 x 10 x 5 cm (4.9 x 4 x 2 inches) |
| Package Weight | 80g (2.8 oz) |
User Tips
- Keep Spares Handy: With 6 lenses included in one pack, you have a sufficient reserve to ensure uninterrupted operation of your laser module. Always have a spare lens ready for quick replacement.
- Regular Cleaning: Even with anti-oil and anti-smoke properties, regular cleaning with alcohol will significantly extend the effective lifespan and maintain the high performance of your lenses.

Warranty and Support
For any problems or inquiries regarding your SCULPFUN S30 Pro Max laser lenses, please do not hesitate to contact the store where you purchased the product. They will be able to assist you with troubleshooting or provide further support.