Godox iT20 R

Contents

Godox iT20 R TTL Mini Flash Instruction Manual

Model: iT20 R

This manual provides detailed instructions for the safe and effective use of your Godox iT20 R TTL Mini Flash.

1. Product Overview

The Godox iT20 R TTL Mini Flash is a compact and versatile camera flash designed for compatible cameras, including Ricoh and Pentax P-TTL systems. Its small size allows it to integrate seamlessly with your camera setup. It supports both TTL auto flash and manual flash modes, offering precise control over lighting.

Key features include a wide flash power range (1/32 to 1/1) with ±1/3 stop adjustments, flash exposure compensation (FEC) of ±3 stops, and a built-in high-energy lithium battery for extended use. The flash also comes with magnetic accessories like a diffuser and color filters to enhance creative lighting possibilities.

Godox iT20R Mini Flash highlighting features: TTL Auto Flash, Ultra-compact (45g), Magnetic Accessories, Lithium Battery, 700+ Full Power Flashes, 1.5s Rapid Recycling.
Figure 1: Godox iT20R Mini Flash highlighting its compact design, TTL auto flash, magnetic accessories, lithium battery, 700+ full power flashes, and 1.5s rapid recycling.
Hand holding the 45g ultra-compact Godox iT20R Mini Flash.
Figure 2: The ultra-compact and lightweight design of the Godox iT20R Mini Flash.

2. Setup

2.1 What's in the Box

Please check the contents of your package:

  • Flash Body (x1)
  • USB-C Charging Cable (x1)
  • Storage Bag (x1)
  • Instruction Manual (x1)
  • Magnetic Spreader (x1)
  • Magnetic Color Filter (x2)
Contents of the iT20 Silver box: Flash Body, USB-C Charging Cable, Storage bag, Magnetic Spreader, 1/2 CTO Magnetic Color Filter, 1/1 CTO Magnetic Color Filter.
Figure 3: Contents of the iT20 Silver package, including the flash body, charging cable, storage bag, magnetic spreader, and two magnetic color filters.

2.2 Installation and Removal

Before installation, ensure both the camera and flash are powered off.

  1. Installation: Press and hold the release button on the flash while inserting the camera hot shoe connector parallelly into the camera's hot shoe until it is securely in place.
  2. Removal: Press and hold the release button on the flash and slide it out of the camera's hot shoe.
Video 1: An operation tutorial demonstrating the installation, flash modes, additional features, and magnetic attachments of the Godox iT20 iFlash Camera Flash.

2.3 Power On/Off

  • Turn On: Long-press the power key (marked 'M') until the display lights up.
  • Turn Off: Long-press the power key until the display turns off.

2.4 Charging

The iT20 R features a built-in lithium battery. Use the provided USB-C charging cable to connect the flash to a power source or portable power bank. The charging time is approximately 1 hour and 10 minutes.

The battery level is indicated by a symbol on the display. Three bars indicate a full charge. Please charge the flash promptly when only one bar remains.

3. Operating Instructions

3.1 Flash Modes

The iT20 R supports two main flash modes: Manual Flash (M) and TTL Auto Flash.

3.1.1 Manual Flash (M Mode)

  • Short press the 'M' button to switch to M mode. The display will show 'M'.
  • Press the '-' or '+' buttons to adjust the flash power. The power can be adjusted from 1/32 to 1/1 (full power) in ±1/3 stop increments.
  • Long-press the '-' or '+' buttons for quick adjustment.

3.1.2 TTL Auto Flash

  • Short press the 'M' button to switch to TTL mode. The display will show 'TTL'.
  • Press the '-' or '+' buttons to adjust the Flash Exposure Compensation (FEC) value. FEC can be adjusted within ±3 stops in ±1/3 stop increments.
  • Long-press the '-' or '+' buttons for quick adjustment.
  • When the flash power reaches its maximum, a 'MAX' icon will be displayed. If underexposure occurs, adjust the camera's parameters.
Godox iT20R Mini Flash on a camera, emphasizing 'Smart TTL, Effortless Results'.
Figure 4: The Godox iT20R Mini Flash mounted on a camera, illustrating its smart TTL capabilities for effortless lighting.

3.2 Magnetic Attachments

The iT20 R comes with magnetic accessories to modify the light output. These include a spreader (iT20-DF) and various magnetic color filters (MA01).

  • Spreader (iT20-DF): Attaches magnetically to the flash head to diffuse the light, creating a softer, more even illumination.
  • Magnetic Color Filters (MA01): These filters come in various colors (e.g., 1/2 CTO, 1/1 CTO, 1/2 CTB, 1/1 CTB, 1/1 TTG, Blue, Green, Cyan, Magenta, Yellow) and can be magnetically attached to the flash head to change the color temperature or add creative color effects to your photos.
Three images showing different flash intensities, demonstrating 'Precise Power Control'.
Figure 5: Demonstration of precise power control, showing how adjusting flash intensity affects the lighting of a subject.

4. Maintenance

4.1 Cleaning

When cleaning the device, use a dry, soft cloth to wipe gently. Do not use a wet cloth, as this may damage the device.

4.2 Battery Care

The iT20 R uses a built-in lithium battery. Please observe the following guidelines for optimal battery life and safety:

  • Always use the dedicated charger for charging.
  • Charge and discharge the battery to approximately 50% before storing.
  • For long-term storage, replenish the battery to about 50% every 6 months. Failure to do so may lead to permanent performance degradation or battery failure due to over-discharge.
  • Store the battery at temperatures between 0°C and 40°C.
  • Do not disassemble, crush, or puncture the battery.
  • The battery is not waterproof; do not immerse it in water or other liquids.
  • Avoid short-circuiting battery contacts.
  • Keep the battery away from fire and high temperatures (above 60°C).
  • Keep the battery out of reach of children.
  • Prevent the battery from excessive impact or vibration.
  • Do not use damaged batteries.
  • If battery leakage occurs, avoid contact with the leaked fluid. If fluid contacts eyes, rinse immediately with water for at least 15 minutes and seek medical attention.

4.3 Thermal Protection

To prevent overheating and damage to the flash head, avoid rapid, continuous flashes, especially at 1/1 power. If the internal overheating protection is activated (indicated by a thermal protection symbol on the display), the recycling time may increase to over 10 seconds. Allow the flash to cool down for approximately 10 minutes before resuming use.

Approximate continuous flash counts before thermal protection activates:

Flash PowerContinuous Flashes
1/140
1/279
1/4166
1/8250
1/16600
1/321500

5. Troubleshooting

The system continuously monitors for abnormal conditions. If an issue occurs, an error code will be displayed. Refer to the table below for guidance:

Display CodeWarning ContentSuggested Action
E1Flash recycling system issue, unable to recycle or trigger.Restart the device. If the issue persists, contact after-sales service for repair.
E2Internal temperature of the device is too high.Stop triggering for approximately 10 minutes. Resume use after the device has cooled down.
E3Voltage across the flash tube is too high.There may be a hardware fault. Contact after-sales service for repair.
E9Firmware upgrade error.Perform the firmware upgrade process correctly again.

5.1 Auto Power-off

If the sleep mode is enabled and the flash is not connected to a camera, the device will automatically power off after 8 hours of inactivity.

5.2 System Reset

If the device experiences an abnormality, you can perform a system reset by simultaneously pressing and holding the '-' and '+' buttons. Then, long-press the power key to restart the device.

6. Specifications

Technical data for the Godox iT20 R TTL Mini Flash:

FeatureSpecification
ModeliT20 S/iT20 C/iT20 N/iT20 F/iT20 O/iT20 R
Compatible BrandPentax/Ricoh (for iT20 R)
TTLYes
High-speed synchronous (HSS)Yes
DisplayYes
Built-in Lithium Battery7.4V, 300mAh
Charging TimeApprox. 1h 10min
Flash Times (1/1 Power)Approx. 700
Recycling Time (1/1 Power)Approx. 1.5s
Synchronization TriggerHot Shoe
Dimensions (iT20)41.5x41x32 mm
Dimensions (iT22)40x64x28 mm
Net Weight (iT20)Approx. 45g
Net Weight (iT22)Approx. 52g
Operating Environment Temperature-10°C to +50°C

Specifications and parameters are subject to change without prior notice.

7. Warranty and Support

7.1 Warranty Information

The product warranty period and service type are subject to the 'Product Warranty Information' table. The warranty period starts from the date of first purchase, as recorded on the warranty card. Consumables such as batteries, adapters, and power cables are not covered under warranty.

Unauthorized repairs will void the warranty. Faults caused by improper operation are not covered by the warranty. Normal discoloration, wear, and tear during product use are not considered faults covered by the warranty.

For detailed warranty terms and conditions, please refer to the official user manual PDF available at Godox iT20 User Manual (PDF).

7.2 Contact Support

For warranty service or technical support, you may contact the product seller or an authorized service agency. You can also reach Godox after-sales service at +86-755-29609320 (ext. 8062) or via email at godox@godox.com.

When applying for warranty service, you should provide a valid warranty card as proof of purchase. If you cannot provide a valid warranty card, service may still be provided if the product or component is confirmed to be within the warranty scope, but this is not an obligation.

8. User Tips

  • Creative Lighting: Experiment with the magnetic color filters to add artistic flair to your photos. The diffuser is excellent for softening harsh light, especially in close-up shots.
  • Battery Management: To maximize battery life, avoid completely draining the battery frequently. Charge it when the indicator shows one bar.
  • Quick Adjustments: Utilize the long-press function on the '+' and '-' buttons for faster adjustments of flash power or FEC, saving time during shoots.
  • Firmware Updates: Keep an eye on the manufacturer's website for any firmware updates. To check your current firmware version, long-press the '+' button while powering on the device.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.