Hobbywing X9 Plus G2L Motor 9620-80KV

Contents

Hobbywing X9 Plus G2L Motor 9620-80KV Integrated Power System

User Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your Hobbywing X9 Plus G2L Motor 9620-80KV Integrated Power System. This system is designed for high-performance applications, particularly in agricultural drones, offering significant thrust and reliability. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product.

Hobbywing X9 Plus G2L Motor, ESC, and propeller
Figure 1: Hobbywing X9 Plus G2L Motor, ESC, and propeller assembly.

2. Safety Precautions

  • Always handle the power system with care.
  • Ensure all connections are secure and properly insulated before applying power.
  • Keep hands and loose clothing away from rotating propellers.
  • Operate in a well-ventilated area.
  • Do not disassemble the motor or ESC unless specifically instructed.
  • Use only compatible batteries (12S-14S LiPo) and propellers.
  • In case of malfunction, immediately disconnect power.

3. Package Contents

The Hobbywing X9 Plus G2L Integrated Power System typically includes the following components:

  • X9 Plus G2L Motor (9620-80KV)
  • Integrated Electronic Speed Controller (ESC)
  • Propeller (e.g., 4314 folding propeller)
  • Mounting hardware and cables
Components of the X9 Plus G2L system: motor, ESC, and propeller
Figure 2: Typical components included in the X9 Plus G2L system.
X9 Plus G2L motor and ESC assembly
Figure 3: Close-up of the X9 Plus G2L motor and ESC assembly.

4. Specifications

4.1. All-in-One Thrust System Specification

ParameterValueParameterValue
ModelCM-X9-Plus-G2LMax Thrust28 kg (Sea level)
Recommended takeoff weight per axis12-14 kg (Sea level)Efficiency of recommended takeoff weight8.6-8.0 g/W
Compatible lithium battery12S-14S (LiPo)Rated voltage14S-54V / 12S-48V
Input voltage18-63 VTube outer diameterD45 mm
Weight (with cable and propeller)1852 g*Cable specificationPower cable: 12AWG 1050 mm* Signal cable: 1090 mm*
Operating temperature-20~50 °CIngress ProtectionIPX6
Rated power input1700 WRated power output1440 W
PinoutBlack-GND, White-PWM & Red-CH, Gray-CL

*Subject to the actual product.

All-in-One Thrust System Specification table
Figure 4: All-in-One Thrust System Specification.

4.2. ESC Specification

ParameterValueParameterValue
Model150A-FOCCommunication protocolCyphal (UAVCAN)
Peak current (3s)150A (3s)Continuous current40 A
Throttle range calibrationNot supportedThrottle SourcePWM+CAN
Operating pulse width1050-1950 μsFault storage & LogSupported
ESC Specification table
Figure 5: Electronic Speed Controller (ESC) Specification.

4.3. Motor Specification

ParameterValueParameterValue
Model9620-80KVSlot & Pole36N40P
Stator diameter96*20 mmMotor diameter104 mm (Fan 130 mm)
Motor Specification table
Figure 6: Motor Specification.

4.4. Propeller Specification

ParameterValueParameterValue
Model43"*14" (Folding propeller)Total Weight427 g*
Material of BladesCarbon fibre-reinforced nylon composite materialSingle blade weight146 g*

*Subject to the actual product.

Propeller Specification table
Figure 7: Propeller Specification.

4.5. Thrust Test Data (48V, 12S LiPo)

Voltage(V)PropellerThrottle(%)Thrust(g)Current(A)Power Input(W)Speed(RPM)Efficiency(g/W)Torque(N·m)Power Output(W)Temperature(°C)
48V (12S LiPo)43"*14"37%49927.9377.9127813.22.36315.8
39%597110.1484.1139512.32.80409.0
42%701912.8613.4151311.43.28519.6
45%793615.4737.9161010.83.71625.5
48%907918.8905.0172310.04.24765.0
51%1107725.51226.519029.05.171029.7
54%1190628.51368.919718.75.561147.5
57%1296732.51559.220558.36.051301.9
60%1405436.71762.621378.06.561467.9
63%1607445.12166.622807.47.491788.2
66%1699549.22363.123437.27.921943.1/
69%1910759.32847.124846.78.892312.3
72%2005564.23082.225466.59.332487.3
75%2100269.43330.526086.39.782670.8
78%2308981.93928.927455.910.763092.8
81%2397787.74208.328025.711.183280.2
84%2502795.14561.928695.511.683508.9
87%25985102.34906.929295.312.133720.3
90%26967110.25283.829895.112.593940.5
93%28008119.15712.830484.913.084174.6
100%28145120.45771.730564.913.144204.8

*The above data was measured by HOBBYWING Laboratory at room temperature 25°C, at sea level, with varying throttle input, for reference only.

Thrust Test Data table (48V, 12S LiPo)
Figure 8: Thrust Test Data for 48V (12S LiPo) with 43"*14" propeller.

4.6. Load Performance Parameters (48V) Graph

Load Performance Parameters (48V) Graph
Figure 9: Graph illustrating Load Performance Parameters at 48V, showing relationships between torque, speed, efficiency, current, and power output.

4.7. Physical Dimensions and Wiring Diagram

Technical drawing with dimensions and wiring diagram for the motor and ESC
Figure 10: Technical drawing showing the dimensions of the motor and ESC assembly, along with a detailed wiring diagram. Key pinouts are Black-GND, White-PWM & Red-CH, Gray-CL. Power cable is 12AWG 1050mm, signal cable is 1090mm.

4.8. Propeller Dimensions

Technical drawing of the propeller with dimensions
Figure 11: Technical drawing detailing the dimensions of the 43"*14" folding propeller.

4.9. Package Dimensions

  • Length: 20 cm
  • Width: 15 cm
  • Height: 10 cm
  • Weight: 2.0 kg

5. Setup and Installation

The Hobbywing X9 Plus G2L is an integrated power system, simplifying installation. Follow these general steps:

  1. Mounting: Securely attach the motor assembly to your drone's frame using appropriate mounting hardware. Refer to Figure 10 for mounting hole patterns and dimensions.
  2. Propeller Installation: Attach the propeller blades to the motor hub. Ensure they are correctly oriented (CW for clockwise, CCW for counter-clockwise rotation) and tightened according to the manufacturer's recommendations. Refer to Figure 11 for propeller dimensions.
  3. Wiring: Connect the power cables from the ESC to your battery distribution board (PDB) or directly to the battery connector, ensuring correct polarity (red to positive, black to negative). Connect the signal cable (PWM/CAN) from the ESC to your flight controller. Refer to Figure 10 for the pinout: Black-GND, White-PWM & Red-CH, Gray-CL.
  4. Initial Checks: Before flight, perform a motor direction test (without propellers) to confirm correct rotation. Ensure all connections are firm and there are no loose wires.
Video 1: Demonstration of the X9 Plus G2L motor and ESC assembly, showing its components and how they fit together.

6. Operating Instructions

Once the power system is installed and checked, you can proceed with operation:

  1. Power On: Connect the battery to the system. The ESC will typically emit a series of beeps indicating initialization.
  2. Flight Controller Integration: Ensure your flight controller is properly configured to communicate with the ESC via PWM or CAN (Cyphal/UAVCAN protocol).
  3. Arming: Follow your flight controller's arming procedure.
  4. Throttle Control: Gradually increase throttle to initiate motor rotation. Monitor motor and ESC temperatures during initial operation.
  5. Disarming: After operation, disarm the flight controller and disconnect the battery.

7. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your power system:

  • Cleaning: Keep the motor and ESC free from dust, dirt, and moisture. Use a soft brush or compressed air for cleaning.
  • Inspection: Periodically check all cables and connectors for signs of wear, damage, or corrosion. Ensure propellers are free from cracks or damage.
  • Fasteners: Verify that all mounting screws and propeller fasteners are tight.
  • Storage: Store the power system in a dry, cool environment away from direct sunlight and extreme temperatures.

8. Troubleshooting

If you encounter issues, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Motor not spinningLoose connection, incorrect wiring, ESC not armed, faulty component.Check all wiring, ensure battery is charged, verify flight controller arming sequence, inspect for damage.
Motor stutters or vibratesPropeller imbalance, loose motor mount, ESC timing issue, damaged motor bearing.Balance propellers, tighten motor mounts, check ESC settings, inspect motor for physical damage.
ESC overheatingOverload, insufficient cooling, incorrect propeller size.Reduce load, ensure adequate airflow around ESC, verify propeller is within specifications.
Loss of power during flightLow battery voltage, loose battery connection, ESC thermal shutdown.Check battery charge, secure battery connection, allow ESC to cool if thermal shutdown occurred.

9. User Tips

  • For optimal performance and longevity, always operate the system within its specified voltage and current limits.
  • Consider using a power analyzer during initial setup to verify current draw and power consumption under various loads.
  • Regularly check for firmware updates for the ESC from the Hobbywing official website to ensure you have the latest features and bug fixes.
  • When replacing propellers, ensure they are balanced to prevent vibrations that can affect flight stability and component lifespan.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact Hobbywing directly or your authorized dealer. Keep your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.