KEYDIY KD FGB23

Contents

KEYDIY KD FGB23 Remote PCB Instruction Manual

Model: KD FGB23 | Brand: KEYDIY

1. Introduction

The KEYDIY KD FGB23 Remote PCB is a high-quality circuit board designed for use in remote keys for specific BMW vehicles. This manual provides essential information for the proper setup, operation, and maintenance of your KD FGB23 Remote PCB to ensure optimal performance and longevity.

2. Product Overview and Key Features

The KEYDIY KD FGB23 is specifically designed for BMW vehicles equipped with G-chassis (BDC2/BDC3) and F-chassis (FEM/BDC) systems. It offers a reliable and cost-effective solution for key generation.

Key Advantages of the KEYDIY FGB Series:

  • Wide System Compatibility: Supports compatible systems including CAS4/CAS4+, FEM/BDC, and BDC2/BDC3 (G-series).
  • Cost-Effective Key Generation: No extra tokens or points are required for key generation after the initial BMW G/F license is activated.
  • Stable & Reliable Performance: Built with high-quality 434MHz FSK PCBs for stable, accurate, and long-distance signal transmission.
  • Strong Compatibility with Programmers: Works perfectly with KEYDIY programmers such as KD-X4, KD-MAX, and KD-MATE.
  • Flexible Application: Can be used as dedicated smart keys for compatible systems or as standard ZB-type smart keys for other vehicles.
Overview of KEYDIY FGB23 remote key components
Figure 1: Overview of KEYDIY FGB23 remote key components, including multiple key shells and the PCB.
Close-up view of the KEYDIY FGB23 Remote PCB
Figure 2: Close-up view of the KEYDIY FGB23 Remote PCB, showing electronic components.

3. Specifications

FeatureDetail
ModelKD FGB23
Frequency434MHz FSK
OriginMainland China
Package Length23 cm
Package Width18 cm
Package Height3 cm
Package Weight0.08 kg

4. Compatibility

The KEYDIY KD FGB23 Remote PCB is compatible with the following BMW car models and systems (for reference only; a comprehensive judgment based on multiple factors and conditions is recommended):

  • Systems: CAS4/CAS4+, FEM/BDC, BDC2/BDC3 (G-series)
  • Car Models:
    • Series 5 G30 (11/2016-06/2020)
    • Series 5 G31 (03/2017-06/2020)
    • Series 5 G38 (05/2017-08/2020)
    • Series 6 G32 (07/2017-06/2020)
    • Series 7 G11/G12 (07/2015-02/2019)
    • M5 F90 (11/2017-06/2020)
    • X3/iX3 G08 (05/2018-08/2021)
    • X3 F97 (04/2019-07/2021)
    • X3 G01 (12/2017-07/2021)
    • X4 G02 (04/2018-07/2021)
    • X4 F98 (04/2019-07/2021)

5. Package Contents

Your package will include either:

  • 1x KEYDIY KD FGB23 Remote PCB (as shown in Figure 2)
  • OR
  • 1x KEYDIY KD FGB23 Remote PCB with 1x compatible key shell (as shown in Figure 1)

Please verify the contents of your package upon receipt.

6. Setup and Installation

The installation and programming of the KEYDIY KD FGB23 Remote PCB require specialized tools and expertise. It is highly recommended that this process be performed by a qualified automotive locksmith or technician.

  1. Prepare Key Shell (if PCB only): If you purchased the PCB only, ensure you have a compatible key shell. Refer to Figure 3 and Figure 4 for examples of key shell components.
  2. Insert PCB: Carefully place the KD FGB23 PCB into the designated slot within the key shell. Ensure it is seated correctly and securely.
  3. Install Battery: Insert a CR2032 coin cell battery into the battery compartment. Refer to Figure 5 for the battery placement within the key shell.
  4. Assemble Key Shell: Close and secure the key shell.
  5. Key Blade Cutting (if applicable): If your package includes a key blade (Figure 6), it will need to be cut by a locksmith to match your vehicle's ignition or door lock.
  6. Programming: Connect a compatible KEYDIY programmer (e.g., KD-X4, KD-MAX, KD-MATE) to your vehicle's diagnostic port. Follow the programmer's instructions to generate and program the key to your vehicle's immobilizer system. This step requires the appropriate BMW G/F license activated on your KEYDIY programmer.
Front view of a KEYDIY remote key shell
Figure 3: Front view of a KEYDIY remote key shell with buttons.
Side view of a KEYDIY remote key shell
Figure 4: Side view of a KEYDIY remote key shell.
Internal view of the key shell, showing battery compartment
Figure 5: Internal view of the key shell, showing the battery compartment (CR2032) and space for the PCB.
Detachable key blade for the remote key
Figure 6: Detachable key blade for the remote key.

7. Operating Instructions

Once the KEYDIY KD FGB23 Remote PCB is correctly installed in a key shell and successfully programmed to your vehicle, it will function as a standard BMW smart key. Its operation typically includes:

  • Lock/Unlock: Press the respective buttons to lock or unlock your vehicle's doors.
  • Trunk Release: Press the trunk button to open the vehicle's trunk.
  • Engine Start: For vehicles with keyless start, the key must be detected inside the vehicle to allow engine ignition. For vehicles requiring key insertion, insert the key into the ignition slot.
  • Panic Alarm: If equipped, press and hold the panic button to activate the vehicle's alarm.

Refer to your BMW vehicle's owner's manual for specific instructions on using your smart key features.

8. Maintenance

To ensure the longevity and reliable performance of your KEYDIY KD FGB23 Remote PCB and key:

  • Battery Replacement: The key uses a CR2032 coin cell battery. When the key's range decreases or it stops responding, it's likely time to replace the battery. Open the key shell (refer to Figure 5 for battery location), remove the old battery, and insert a new CR2032 battery with the correct polarity.
  • Keep Dry: Avoid exposing the key to water or excessive moisture, as this can damage the internal electronics.
  • Avoid Extreme Temperatures: Do not leave the key in direct sunlight or in extremely hot or cold environments for extended periods.
  • Handle with Care: Avoid dropping the key or subjecting it to strong impacts.
  • Cleanliness: Keep the key clean and free from dirt or debris that could interfere with button operation.

9. Troubleshooting

If you encounter issues with your KEYDIY KD FGB23 Remote PCB or key, consider the following:

  • Key Not Responding:
    • Check the battery. Replace the CR2032 battery if it's low or dead.
    • Ensure the key is within range of the vehicle.
    • Verify that the key is properly programmed to the vehicle. If it was recently programmed, there might have been an issue during the process.
  • Reduced Range:
    • This is a common symptom of a low battery. Replace the CR2032 battery.
    • Environmental interference can also affect range. Try using the key in a different location.
  • Buttons Not Working:
    • Check for physical obstructions or damage to the buttons.
    • Ensure the PCB is correctly seated within the key shell and not misaligned.
  • Vehicle Not Starting (Keyless Start):
    • Ensure the key is detected inside the vehicle. Try placing it in the designated key slot or near the steering column.
    • A low key battery can also prevent keyless start.

For persistent issues, it is recommended to consult with a professional automotive locksmith or technician who has experience with KEYDIY products and BMW vehicle systems.

10. User Tips

No specific user tips were available from reviews or Q&A for this product at this time. However, general tips for remote keys include:

  • Always carry a spare key, if available, in case of battery failure or key loss.
  • Avoid storing your key near strong magnetic fields or electronic devices that could cause interference.
  • If you have multiple keys, test each one periodically to ensure they are all functioning correctly.

11. Warranty and Support

For warranty information, technical support, or any questions regarding your KEYDIY KD FGB23 Remote PCB, please contact the seller or the official KEYDIY support channels. Keep your purchase receipt or order details handy when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.