ANDELI MIG-160

Contents

ANDELI MIG-160 4-in-1 Multi-Process Welder

Model: MIG-160 | Brand: ANDELI

Your comprehensive guide to operating and maintaining your ANDELI MIG-160 welder.

1. Introduction

The ANDELI MIG-160 is a versatile 4-in-1 multi-process synergic welder designed for a wide range of welding applications. It supports Gas MIG, Flux MIG, Lift TIG, and MMA (Stick) welding, making it suitable for both beginners and experienced users. This machine is compatible with 10LB (5KG) welding wire and operates on a 220V power supply.

ANDELI MIG-160 4-in-1 Welder with accessories
Figure 1: ANDELI MIG-160 4-in-1 Multi-Process Welder

This manual provides essential information for the safe and efficient operation, setup, and maintenance of your MIG-160 welder. Please read it thoroughly before use.

2. Safety Information

Always prioritize safety when operating welding equipment. Failure to follow safety precautions can result in serious injury or death.

  • Wear appropriate personal protective equipment (PPE), including a welding helmet with proper shade, flame-resistant clothing, welding gloves, and safety shoes.
  • Ensure adequate ventilation to avoid inhaling welding fumes.
  • Protect bystanders from arc rays and hot metal.
  • Always disconnect power before performing any maintenance or changing accessories.
  • Do not operate the welder in wet conditions or near flammable materials.
  • Ensure the machine is properly grounded.
Safety Assurance features: Overheat, Overcurrent, Overvoltage Protection, and Fan Cooling System
Figure 2: Built-in Safety Features

The MIG-160 includes built-in safety features such as Overheat Protection, Overcurrent Protection, Overvoltage Protection, and a Fan Cooling System to enhance user safety and machine longevity.

3. Package Contents

Verify that all items listed below are included in your package:

Image showing the package contents including MIG-160 Air Welder, MIG Torch, Adapter, Welding Wire, Welding Rods, Contact Tips, Cups, Electrode Holder, Ground Clamp, and Air Hose.
Figure 3: Included Accessories
  • MIG-160 Air Welder * 1
  • 15AK MIG Torch * 1
  • 220V to 110V Adapter * 1 (if applicable to your region)
  • Welding Wire * 1
  • Welding Rod * 5
  • Contact Tips * 5
  • Cups * 2
  • Electrode Holder * 1
  • Ground Clamp * 1
  • Air Hose * 1

4. Machine Overview

Familiarize yourself with the main components of your MIG-160 welder:

Numbered diagram of the MIG-160 welder's external components: 1. LED Display Screen, 2. Wire Diameter & Trigger Mode Selection, 3. Gas Selection, 4. Voltage Control Knob, 5. Current Control Knob, 6. Euro Torch Connector, 7. Wire Drive Polarity Lead, 8. Negative Output Terminal, 9. Positive Output Terminal, 10. Power Switch, 11. Input Power Cable, 12. Cooling Fan, 13. MIG/MAG Gas Inlet.
Figure 4: Machine Component Overview
  1. LED Display Screen
  2. Wire Diameter & Trigger Mode Selection
  3. Gas Selection
  4. Voltage Control Knob
  5. Current Control Knob
  6. Euro Torch Connector
  7. Wire Drive Polarity Lead
  8. Negative Output Terminal
  9. Positive Output Terminal
  10. Power Switch
  11. Input Power Cable
  12. Cooling Fan
  13. MIG/MAG Gas Inlet

5. Control Panel Introduction

The digital display screen and control buttons allow for precise adjustment of welding parameters.

Detailed diagram of the control panel buttons and display: 1. 2T/4T Button, 2. Wire Diameter Selection Button, 3. Feed Wire Speed, 4. Real-Time Voltage, 5. Real-Time Current, 6. Gas Selection Button, 7. Voltage Knob/Inductance Knob, 8. Weld Modes, 9. Current Knob/Weld Mode Button.
Figure 5: Control Panel Layout
  1. 2T/4T Button: Toggles between 2-stroke and 4-stroke trigger modes.
  2. Wire Diameter Selection Button: Selects the appropriate wire diameter (e.g., 0.030, 0.035, 0.040 inches).
  3. Feed Wire Speed: Displays the wire feed speed.
  4. Real-Time Voltage: Displays the current welding voltage.
  5. Real-Time Current: Displays the current welding amperage.
  6. Gas Selection Button: Selects the gas type (CO2, MIX, Ar) or Flux mode.
  7. Voltage Knob/Inductance Knob: Adjusts welding voltage or inductance depending on the mode.
  8. Weld Modes: Indicates the selected welding process (CO2, MIX, FLUX, MMA, TIG).
  9. Current Knob/Weld Mode Button: Adjusts welding current or selects the welding mode.
Close-up of the 3.54 x 1.96 inch digital display screen, highlighting its graphical interface for easier use.
Figure 6: Digital Display Screen

6. Setup

6.1 Power Connection

  • Ensure the power switch (10) is in the OFF position.
  • Connect the input power cable (11) to a suitable 220V power outlet. If using a 110V adapter, ensure it is correctly connected and rated for the welder's power requirements.

6.2 Ground Clamp Connection

  • Connect the ground clamp to the negative output terminal (8) of the welder.
  • Attach the ground clamp securely to the workpiece or a clean, bare metal section of the welding table. A good ground connection is crucial for safe and effective welding.

6.3 Welding Wire Installation (MIG/Flux Core)

  • Open the wire feed compartment.
  • Install the welding wire spool (compatible with 2LB or 10LB spools) onto the spindle.
  • Thread the welding wire through the wire drive mechanism and into the MIG torch liner.
  • Ensure the wire drive polarity lead (7) is correctly set for your chosen wire type (e.g., DCEP for solid wire with gas, DCEN for flux-cored wire).
Image showing the welder's internal compartment for welding wire, indicating compatibility with 2LB (0.8mm/0.030
Figure 7: Welding Wire Capacity and Installation Area

6.4 MIG Torch Connection

  • Connect the Euro Torch Connector (6) of the MIG torch to the corresponding port on the welder.

6.5 Gas Connection (Gas MIG/Lift TIG)

  • For Gas MIG or Lift TIG welding, connect the air hose (from your gas cylinder and regulator) to the MIG/MAG Gas Inlet (13) on the rear of the welder.
  • Ensure all connections are tight to prevent gas leaks.

6.6 MMA (Stick) / Lift TIG Torch Connection

  • For MMA (Stick) welding, connect the electrode holder to the positive output terminal (9).
  • For Lift TIG welding, connect the TIG torch to the negative output terminal (8) and the ground clamp to the positive output terminal (9).

7. Operating Instructions

7.1 Power On and Mode Selection

  • Turn on the power switch (10). The LED display screen (1) will illuminate.
  • Use the Current Knob/Weld Mode Button (9) to cycle through the available welding modes: Gas MIG (CO2/MIX), Flux Core (FLUX), MMA (Stick), and Lift TIG (TIG).
  • For Gas MIG, use the Gas Selection Button (6) to choose between CO2 or MIX gas.
Image illustrating the four welding modes: Gas MIG, Flux Core, Stick, and Lift TIG.
Figure 8: 4-in-1 Welding Machine Modes

7.2 Parameter Adjustment

  • Wire Diameter: Press the Wire Diameter Selection Button (2) to match the diameter of your welding wire.
  • Current/Voltage: Use the Voltage Knob/Inductance Knob (7) and Current Knob/Weld Mode Button (9) to adjust the welding current and voltage according to your material thickness and welding process. The Real-Time Voltage (4) and Real-Time Current (5) will show your settings.
Diagram showing recommended welding material thickness for MIG (0.5-6mm @220V, 30-160A; 0.5-5mm @110V, 30-130A), Lift TIG (0.5-6mm @220V, 30-160A; 0.5-5mm @110V, 30-130A), and Stick (0.5-6mm @220V, 30-160A; 0.5-5mm @110V, 30-130A).
Figure 9: Welding Material Thickness Guidelines

7.3 2T/4T Settings

The 2T/4T button (1) allows you to choose between two trigger modes:

  • 2T (2-Stroke): Hold the trigger to feed wire and weld; release to stop. Simple and precise for short welds.
  • 4T (4-Stroke): Press the trigger once to start automatic wire feeding and welding; press again to stop. Ideal for long welds to reduce hand fatigue.
Diagram explaining 2T (Hold to feed wire, release to stop) and 4T (Press once to start, press again to stop) trigger modes.
Figure 10: 2T/4T Trigger Settings

7.4 SYN & MAN Control Modes

The MIG-160 offers both Synchronous (SYN) and Manual (MAN) control modes:

  • SYN Mode: Current and voltage are automatically matched. Recommended for beginners.
  • MAN Mode: Current and voltage can be controlled separately and precisely. Recommended for skilled workers.
Diagram showing SYN and MAN control modes. SYN mode automatically matches current and voltage (recommended for beginners). MAN mode allows separate and precise control (recommended for skilled workers).
Figure 11: SYN & MAN Control Modes

7.5 Welding Process Overview

For detailed instructions on each welding process (Gas MIG, Flux Core, Lift TIG, MMA), refer to specialized welding guides. Always practice on scrap material before working on your final project.

Video 1: Product demonstration of the MIG-160 welder in various modes.

8. Maintenance

Regular maintenance ensures the longevity and optimal performance of your welder.

  • Cleaning: Regularly clean the machine's exterior and cooling fan (12) vents to prevent dust and debris buildup. Use compressed air to blow out internal dust.
  • Torch and Cable Inspection: Inspect welding torches, cables, and connections for wear, damage, or loose fittings before each use. Replace damaged parts immediately.
  • Wire Feed System: Keep the wire feed rollers clean and ensure they are correctly tensioned for smooth wire feeding. Check the MIG torch liner for blockages or wear.
  • Contact Tips and Nozzles: Replace worn contact tips and clean or replace clogged nozzles on the MIG torch as needed.
  • Ground Clamp: Ensure the ground clamp remains clean and makes good electrical contact.

9. Troubleshooting

This section provides solutions to common issues. For problems not listed here, contact customer support.

Problem Possible Cause Solution
No power to the machine Power cable disconnected, circuit breaker tripped, faulty power switch. Check power connections, reset circuit breaker, contact service if switch is faulty.
No arc / Weak arc Poor ground connection, incorrect settings, worn contact tip, wire feed issue. Ensure good ground, verify settings, replace contact tip, check wire feed path.
Wire not feeding Wire tangled, drive rollers loose/dirty, liner blocked, incorrect wire diameter selected. Untangle wire, clean/adjust drive rollers, clear liner, select correct wire diameter.
Overheat indicator active Exceeded duty cycle, blocked cooling vents, high ambient temperature. Allow machine to cool, clear vents, operate in cooler environment.

10. Specifications

Feature Specification
Model MIG-160
Input Power Single phase 220V±15% 50HZ
Rated Input Capacity 7.2 KW
Rated Output Voltage 26.4 V
Output Current Range 40-200 A
No-load Voltage 55 V
Rated Duty Cycle 30%
Power Factor 0.73
Protection Class IP21S
Insulation Class H
Max. Load Power Capacity 5.9 KW
Rated Input Voltage 220 V
Rated Output Voltage 60 V
Welding Current/Voltage Range 220 V
Material / Metal Processed Stainless Steel, Iron, Carbon Steel
MIG Solid Wire Diameter 0.8 mm, 1.0 mm
Weight (KG) 5
Wire Feeding Speed 12
Wire Melting Type Short Circuit Transfer

11. User Tips

  • For optimal results, always ensure your workpiece is clean and free of rust, paint, or oil.
  • When switching between welding processes, double-check all cable connections and polarity settings.
  • Utilize the SYN mode if you are new to welding or unsure about specific parameter settings, as it provides automatically matched current and voltage for ease of use.
  • For longer welding passes, the 4T trigger mode can significantly reduce hand fatigue.
  • Keep spare contact tips and nozzles on hand, as they are consumable parts and affect weld quality.

12. Warranty and Support

The ANDELI MIG-160 welder comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please contact ANDELI customer service.

© 2026 ANDELI. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.