SUNSHINE P5 Mini

Contents

SUNSHINE P5 Mini Smart Power Supply User Manual

Model: P5 Mini

1. Introduction

1.1 Essential for Users

Users of this product must possess basic life skills and basic electrical operating knowledge. Minors must use this product under the guidance of a professional or guardian.

Caution: To avoid damaging the machine and maintain a safe working environment, please carefully read this product manual before using this product and familiarize yourself with its operation and precautions.

1.2 Safety Precautions

  1. Avoid high temperatures, open flames, corrosive gases, humid or dusty environments to prevent equipment malfunction.
  2. Before operation, check the power supply casing for damage or deformation, the power interface for looseness or damage, and confirm that the connecting cables are undamaged or broken. Any issues will affect the normal operation of the power supply and may even damage the equipment.
  3. Before use, ensure the heat dissipation vents are unobstructed to guarantee good heat dissipation.
  4. Before use, carefully read the power supply's operation manual to familiarize yourself with its operation. This will help you operate the power supply correctly and efficiently, promptly identify and resolve any problems that arise during use, and ensure the power supply's safe and stable operation.
  5. After turning on the power switch, do not adjust the voltage or current to the maximum output value. First, adjust the output parameters to a lower value, and then gradually and slowly adjust the output voltage or current according to the actual load requirements.
  6. During power supply operation, monitor its working status, including whether the output voltage and current are stable, and whether there is any abnormal noise or overheating.

1.3 Disclaimer

Our company is not responsible for any personal injury or property damage caused by failure to follow instructions, force majeure events such as natural disasters, or personal actions that are not due to product quality defects.

2. Setup

The SUNSHINE P5 Mini Smart Power Supply is designed for ease of use. Follow these steps for initial setup:

  1. Unpacking and Inspection: Carefully remove the power supply and all accessories from the packaging. Inspect the unit for any visible damage to the casing or cables. Ensure all components listed in the package contents are present.
  2. Placement: Place the power supply on a stable, flat surface. Ensure that the heat dissipation vents are not obstructed to allow for proper airflow and prevent overheating.
  3. Power Connection: Connect the power cable to the AC Power input socket on the back of the unit. Plug the other end into a suitable AC power outlet (AC110~240V, 50/60Hz).
  4. Connecting Devices: Use the provided cables to connect your device to the DC 0-12V output ports (red for positive, black for negative), or use the USB-C or USB-A ports for compatible devices.
SUNSHINE P5 Mini Smart Power Supply and accessories
Figure 1: SUNSHINE P5 Mini Smart Power Supply and included accessories.
SUNSHINE P5 Mini connected to a smartphone for wired start function
Figure 2: Example of connecting the power supply to a device using the wired start function.

3. Operating Instructions

The P5 Mini features a dual display intelligent screen and intuitive controls.

Close-up of the P5 Mini's digital and analog display showing 12.0V and 3.00A
Figure 3: Digital and Pointer Dual Display Screen for clear work status.
P5 Mini showing intelligent dual-port 5V3A output with USB-C and USB-A ports
Figure 4: Intelligent Dual-Port 5V3A Output with real-time voltage and current display.
  1. Power On/Off: Locate the power switch on the back of the unit. Flip it to the 'On' position to power on the device.
  2. Display Switching: Double-click the encoder knob to switch between displaying the voltage and current of the USB-A and USB-C charging ports. The digital display will flash to indicate this mode. Double-clicking again will exit this display mode.
  3. Output Adjustment: Click the encoder knob to enter the output voltage adjustment interface. One digit of the displayed value will flash. Rotate the encoder to adjust the value of the flashing position. Clicking the encoder again will switch to editing a different digit. The set data will be automatically saved when the flashing stops.
  4. USB-C/USB-A Output: The device is equipped with USB-C and USB-A ports, both supporting 5V/3A output. Note that these ports do not support fast charging protocols.
  5. DC 0-12V Output: Use the banana plug ports for variable DC output.
Video 1: Demonstration of the SUNSHINE P5 Mini Smart Power Supply in operation, showing voltage and current adjustments and device charging.

4. Maintenance

Proper maintenance ensures the longevity and reliable operation of your P5 Mini Smart Power Supply.

  • Cleaning: Regularly clean the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Ventilation: Ensure that the heat dissipation vents are always clear of dust and debris. Blocked vents can lead to overheating and potential damage.
  • Storage: When not in use, store the power supply in a cool, dry place, away from direct sunlight, high temperatures, open flames, corrosive gases, and excessive humidity or dust.
  • Cable Care: Periodically inspect all connecting cables for signs of wear, damage, or loose connections. Replace any damaged cables immediately.

5. Troubleshooting

If you encounter any issues with your P5 Mini, refer to the table below for common problems and solutions. If the problem persists, please contact customer support.

Common Faults Solution
The machine does not work after the power is connected
  1. Check that the power cord is properly connected and that the voltage is correct.
  2. Disassemble the machine to check whether the internal components are properly connected.
Current display abnormal
  1. Please check that all connecting cables are making good contact.
  2. Disconnect the output port and check if the current display returns to zero.
Overcurrent Protection (OCP) triggered

When the banana plug output is short-circuited or the current exceeds 3.1A, the display will show "E77 OCP". The unit will attempt to restart every 5 seconds. Remove the short circuit or reduce the load.

6. Specifications

Detailed technical specifications for the SUNSHINE P5 Mini Smart Power Supply:

Parameter Value
Product ModelP5 Mini
Input VoltageAC110~240V, 50/60Hz
Output Voltage Range0.6~12V
Output Current Range0~3A
Maximum Output Power0~45W
Output Resolution0.01V/0.01A
RippleVoltage ≤200mVrms
Output Temperature CoefficientVoltage 150ppm / Current 150ppm
Usage EnvironmentFor indoor use; altitude ≤2000m; ambient temperature: 0-40°C; relative humidity: ≤80%
Storage EnvironmentAmbient temperature: -10~70°C; Relative humidity: ≤70%
Charging Port (USB-C)5V, 3A (does not support fast charging protocols)
Charging Port (USB-A)5V, 3A (does not support fast charging protocols)
Net Weight≈ 280g
Gross Weight≈ 460g
Product Size132*81.8*88mm
Package Size136*113*104mm
Diagram showing the dimensions of the P5 Mini Smart Power Supply
Figure 5: Product dimensions of the P5 Mini.

7. Warranty and Support

7.1 Product Warranty

The warranty period for this product is calculated from the date of purchase. During the warranty period, if any malfunction occurs due to normal use, the original warranty card can be presented to enjoy free service at a designated authorized repair company (or our company). Please retain the purchase voucher and this warranty card, and present them together for repair.

Paid repair services will be implemented in the following situations:

  • Unable to present valid warranty cards or valid vouchers.
  • Failure to complete or alter the warranty card for items such as product purchase date and sales unit name.
  • Damage caused by not following the instructions and precautions in the user manual.
  • Damage caused by disassembly, repair, or modification of products without authorization from the manufacturer.
  • Vulnerable and consumable items.

Each item of the warranty card needs to be fully filled out by the agent or user directly to obtain a 12-month warranty period. Please keep this warranty card properly and do not replace it if lost.

7.2 Contact Information

Guangzhou Sunshine Electronics Technology Co., Ltd.

  • Executive Standard: Q/XXDZ 005-2023
  • Address: 5th Floor, Building 3, Liando U valley, No.105, Shilong North Road, Nanhai District, Foshan City
  • Website: www.exinxun.com
  • Customer Service Hotline: 400-038-0255

A detailed user manual in PDF format is available for download. Please refer to the official website or the provided QR code for access.

8. User Tips

  • Upon receiving the product, carefully inspect the packaging and the unit itself for any damage during transit. Even if the box is slightly crushed, the device is often intact.
  • The P5 Mini includes Overcurrent Protection (OCP), which is a valuable safety feature. Ensure you understand its operation as described in the troubleshooting section.

9. Frequently Asked Questions (FAQ)

Q: What is the maximum output voltage of this power supply?
A: The maximum output voltage range is 0.6V to 12V.

© 2024 SUNSHINE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.