JIKONG JK BMS B2A24S20P

Contents

JIKONG JK BMS B2A24S20P User Manual

Model: JK BMS B2A24S20P | Brand: JIKONG

1. Product Overview

The JIKONG JK BMS (Battery Management System) B2A24S20P is an intelligent protection board designed for large capacity series lithium battery packs. It offers comprehensive management and protection features, ensuring the safety and longevity of your battery system.

Key features include voltage acquisition, high current active balancing, overcharge, over-discharge, overcurrent, and over-temperature protection, coulomb metering, Bluetooth communication, and optional GPS remote functionality. This BMS is compatible with LiFePO4, ternary lithium, and lithium titanate (LTO) battery types.

JIKONG JK BMS B2A24S20P main unit
Figure 1: JIKONG JK BMS B2A24S20P Main Unit

1.1 Functional Characteristics

  • LED Bluetooth status indicator
  • APP Bluetooth remote operation (iOS/Android/HarmonyOS support)
  • Battery capacity calculation
  • High precision voltage acquisition (±3mV)
  • High precision current acquisition
  • Support information screen display
  • Accurate time logging
  • Support RS485 (Optional)
  • Support CAN (Optional)
  • Support alarm function (Optional)
  • Support parallel function (Optional)
  • Support heating function (Optional)
  • Support GPS communication (Optional)
  • Support ACC detection function (Optional)
  • Charge overcurrent protection
  • Charge overvoltage protection
  • Charge over temperature protection
  • Low temperature protection during charge
  • Discharge overcurrent protection
  • Discharge undervoltage protection
  • Discharge over temperature protection
  • Short circuit protection
Icons representing various interfaces and functions: CAN, RS485, BT, NTC, Soft Switch, SOC Indicator, Key Switch, Active Equalizer
Figure 2: Rich Interface Options

1.2 Application Scenarios

This BMS is suitable for a wide range of applications, including:

  • E-bikes
  • Electric Tricycles
  • Low Speed Quads
  • Forklifts
  • Cleaning Cars
  • Tourist Cars
  • Industrial Drones
  • Scooters
  • RV Energy Storage
  • General Lithium Battery packs
  • Power Banks
  • Storage Battery systems
Grid of images showing various application scenarios for the BMS, including E-bike, Electric Tricycle, Low Speed Quad, Forklift, Cleaning Car, Tourist Car, Industrial Drone, Scooter, RV Energy Storage, Lithium battery, Power Bank, Storage battery.
Figure 3: Wide Range of Application Scenarios

2. Specifications

2.1 General Specifications (200A Model)

ParameterValueUnit
Supply Voltage20-100V
Operating Power Consumption<800mW
Operating Temperature-30 to 70°C
Max. Number of Collection Strings24Strings
Max. Balancing Current2A
Max. Charging Current200A
Max. Discharge Current200A
Max. Instantaneous Current400A
Max. Internal Loop Resistance0.275mΩ
Protective Plate Size (L×W×H)162×102×20.4mm
Finished Weight560g
Top and bottom view of the BMS with dimensions: 162mm length, 102mm width, 20.4mm height.
Figure 4: Product Dimensions

2.2 Default Parameters

The BMS comes with default parameters for various battery types. These can be adjusted via the APP.

ParameterLi-Ion (Default)LiFePO4 (Default)LTO (Default)Unit
Balancing Initial Voltage332V
Max. Balancing Current222A
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.183.552.65V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay303030S
Charging Overcurrent Protection Release Time606060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Protection Release Time606060S
Short-circuit Protection Delay555µS
Short-circuit Protection Release Time303030S
Charging Overtemperature Protection707070°C
Charging Overtemperature Recovery606060°C
Discharge Overtemperature Protection707070°C
Discharge Overtemperature Recovery606060°C
Charging Low Temperature Protection-20-20-20°C
Charging Low Temperature Recovery-10-10-10°C
MOS Overtemperature Protection100100100°C
MOS Overtemperature Recovery808080°C

3. Setup Instructions

3.1 Packing List

Upon receiving your JIKONG JK BMS, please verify that all components are present:

  1. BMS Unit (x1)
  2. NTC Temperature Sensor (400mm) (x1)
  3. Balance Wires (750mm) (x1)
  4. Switch (500mm) (x1)
  5. Pack Box (x1)
  6. GH1.25mm-4P to SM A connector-2.54-2P+2P-150mm+100mm-CAN-485 Cable (x1)
Diagram showing the packing list components: BMS, NTC, Balance Wires, Switch, Pack box, and CAN-485 cable.
Figure 5: Packing List

3.2 Wiring Diagram

The wiring method for the JK-BxAxxS-15P/20P series protection board varies depending on the number of battery cells (7-24 series). Always ensure correct connections to prevent damage.

Detailed wiring diagram for JK-BxAxxS-15P/20P-24S showing connections for Load, Charger, Heating wire, Temperature control switch, Temperature probe, and balance wires B- to B+.
Figure 6: JK-BxAxxS-15P/20P-24S Wiring Diagram

Important Notes for Wiring:

  • Ensure all balance cables are connected correctly to their respective battery cell positive terminals (B1, B2, ..., B24) and the main negative terminal (B-).
  • Connect the main battery positive (B+) and negative (B-) terminals to the corresponding BMS terminals.
  • Connect the load and charger to the P- terminal and the main battery positive (B+).
  • If using the heating function, connect the heating wire and temperature control switch as shown in the diagram.
  • For CAN/RS485 communication, refer to the specific cable specification and connect accordingly.
Diagram showing the specification and wiring for the Protective Board 2P-CAN/485 Cable, including GH1.25mm-4P to SM A connector and SM B connectors with wire colors and lengths.
Figure 7: Protective Board 2P-CAN/485 Cable Specification

3.3 Connector Definitions

Understanding the pin definitions is crucial for correct wiring and integration.

ConnectorPin No.NameDefinition
P1 (XH-15AW) Balance & Acquisition Interface1B-Total negative battery
2B1The first battery positive
.........
15B14The fourteenth battery positive
P2 (XH-11AW) Balance & Acquisition Interface (Cont.)1B15The fifteenth battery positive
.........
9B23The twenty-third battery positive
10B24The twenty-fourth battery positive (Total battery positive)
11B+Protection board power supply, connected to the battery B+
P3 (XH-4AW) Temperature Interface1T1AFirst temperature sensor pin A
2T1BFirst temperature sensor pin B
3T2ASecond temperature sensor pin A
4T2BSecond temperature sensor pin B
P4 (A1254WF-4A) Communication Interface1RS485_BNegative terminal of RS485 signal
2RS485_ARS485 signal positive terminal
3CAN_HCAN signal positive terminal
4CAN_LCAN signal negative terminal
P5 (1.25T-4PWT) GPS Interface1VGPSPower output, voltage close to B+
2TXUART TX, 3.3V
3RXUART RX, 3.3V
4GNDPower/signal ground
P6 (A1254WF-6A) Display Interface1VCCDisplay power output
2ADisplay RS485 signal positive
3BDisplay RS485 signal negative
4GNDNegative terminal
5K+Activation signal positive
P7 (A1254WF-3A) Parallel Interface1GNDSignal ground
2P-ENParallel module enable signal, output low level to turn on parallel module
3P-statusParallel module status signal
P8 (A1254WF-2A) Alarm Interface1VCCAlarm power supply positive
2GNDAlarm power negative
P9 (A1254WF-5A) ACC Interface (Optional)1ACC+ACC Positive
2ACC-ACC Negative
3NCNot connected
4C_Detect+Charger output 12V positive
5C_Detect-Charger output 12V negative
Heating Wire (16AWG-Orange-15CM)1HT-Heater element negative electrode

3.4 APP Installation

The mobile APP for the JIKONG BMS supports Android (version 7 minimum) and iOS operating systems. To install the APP, scan the QR code below with your smartphone:

QR code for JIKONG Mobile APP link
Figure 8: Mobile APP Link QR Code

3.5 Device Activation

Before powering on the protection board, ensure the following:

  1. Verify that the balance cables are properly connected to each cell.
  2. Confirm that the P- and B- connections are correct.
  3. Ensure the protection board is securely fixed to the battery pack.

The BMS is designed for charging activation. After battery assembly, connect a charger (with voltage 2V higher than battery voltage) to activate the BMS. Alternatively, if you have an optional display screen and button, insert the cable into the display interface and press the button to activate.

4. Operating Instructions

4.1 Active Equalization (Lossless Balancing)

The JIKONG BMS employs active equalization technology to balance cell voltages. This process transfers energy from higher-voltage cells to lower-voltage cells, minimizing energy loss and maximizing battery consistency. The continuous balanced current is typically 0.4A-2A.

Diagram illustrating active balancing, showing energy transfer between battery cells to achieve voltage balance.
Figure 9: Active Balancing Principle

To use the balancing function, set the basic battery parameters (number of cells, battery capacity, trigger equalization differential pressure, voltage calibration, current calibration) in the mobile APP. The balance trigger differential pressure (in mV) can be adjusted. Balancing automatically activates when the voltage difference between any two cells exceeds the set value and turns off when it falls below the set value. It is recommended that the balance current does not exceed 0.2C of the battery capacity. The balancing function can be disabled via the APP if not needed.

4.2 Heating Function (Optional)

The BMS supports an optional heating function to warm the battery in low-temperature conditions, preventing reduced activity and charging/discharging issues. The designed heating current is 10A. Users can enable or disable this function via the BMS control page in the APP based on ambient temperature. It is recommended to install a normally closed temperature switch (45°C to 65°C) in series with the heating circuit as a secondary protection to prevent thermal runaway.4.3 Communication Functions

The JIKONG BMS supports various communication modes, including Bluetooth, RS485, and CAN. The mobile APP allows for remote operation and monitoring of battery status. Users can modify parameters, control charge/discharge switches, and view data. The APP supports multiple languages and can be switched automatically with the mobile phone system.

Screenshots of the JIKONG BMS mobile application showing various settings and monitoring options.
Figure 10: JIKONG BMS Mobile APP Interface

For RS485 and CAN communication, users can select the desired mode via the APP's BMS control page. Specific communication protocols and device addresses can be configured according to your system requirements. An optional LCD display is also available for direct viewing of battery information.

Image showing mobile app, PC software, and LCD display options for monitoring and controlling the BMS.
Figure 11: Multi-screen Display and Data Connection Options

4.4 Parameter Setting

All operational parameters of the BMS, including protection thresholds, delays, and recovery values, can be configured through the mobile APP. Refer to the 'Instructions for Setting Protection Board Parameters' within the APP for detailed guidance on each setting.

5. Maintenance

The JIKONG JK BMS is designed for durability and long-term performance. Regular maintenance primarily involves ensuring proper operating conditions and monitoring through the APP.

  • Environmental Conditions: Ensure the BMS operates within its specified temperature range (-30°C to 70°C) to prevent performance degradation or damage.
  • Connection Integrity: Periodically inspect all wiring connections for tightness and corrosion. Loose connections can lead to unstable operation or system failure.
  • Software Updates: Keep the mobile APP updated to the latest version to benefit from new features, improvements, and bug fixes.
  • Firmware Updates: If firmware updates are released for the BMS, follow the provided instructions carefully to ensure proper installation.
  • Cleaning: Keep the BMS unit clean and free from dust and debris to ensure optimal heat dissipation. The aluminum alloy shell provides superior heat dissipation, but airflow should not be obstructed.
Diagram showing the internal components of the BMS and explaining the fully aluminum alloy shell for superior heat dissipation.
Figure 12: Aluminum Alloy Shell for Heat Dissipation

6. Troubleshooting

The JIKONG BMS incorporates multiple protection functions to safeguard your battery system. Understanding these functions can help in diagnosing and resolving issues.

6.1 Protection Functions and Recovery

  • Overcharge Protection: If any cell voltage exceeds the set overcharge protection voltage during charging, the BMS will stop charging. Charging resumes when all cell voltages drop below the overcharge recovery voltage.
  • Discharge Undervoltage Protection: If any cell voltage drops below the set undervoltage protection voltage during discharge, the BMS will stop discharging. Discharge resumes when all cell voltages rise above the undervoltage recovery voltage. If any cell voltage falls below the automatic shutdown voltage, the BMS will shut down to protect the battery.
  • Charge/Discharge Overcurrent Protection: If the charging or discharging current exceeds the set continuous current for a specified delay, the BMS will stop the respective operation. It will resume after the overcurrent release time. (Note: Continuous current should not exceed 150A/200A depending on model).
  • Over-temperature Protection: If the BMS detects a temperature above the set over-temperature protection value, it will stop charging or discharging. Operation resumes when the temperature drops below the recovery value.
  • Low-temperature Protection (Charging): If the BMS detects a temperature below the set low-temperature protection value during charging, it will stop charging. Charging resumes when the temperature rises above the recovery value. In extremely cold areas, consider using the optional heating function.
  • Short Circuit Protection: The BMS provides short circuit protection. If a short circuit is detected, the BMS will stop operation. Recovery occurs after a set delay. If a short circuit occurs during initial charger connection or load connection, increasing the short circuit protection delay in the APP might resolve it, as high instantaneous currents can trigger protection.

6.2 Alarm Function (Optional)

If the optional alarm function is enabled, the BMS will provide an external alert when it detects safety risks such as over-temperature, overcharge, or over-discharge.6.3 Emergency Switch

The emergency switch function allows the BMS to continue charging and discharging for 30 minutes even if issues like over-temperature, over-discharge, overcharge, or cell string drops occur. This provides a temporary operational window. The BMS will continue to operate until the 30-minute cycle ends, even if a cell reaches the automatic shutdown voltage.

7. User Tips

  • Initial Setup: Always double-check all wiring connections before applying power to avoid damage.
  • APP Monitoring: Regularly use the JIKONG APP to monitor battery health, cell voltages, and temperature. This helps in proactive maintenance and early detection of potential issues.
  • Parameter Customization: Adjust protection parameters (e.g., voltage thresholds, current limits) in the APP to match your specific battery chemistry and application requirements. Incorrect settings can lead to suboptimal performance or damage.
  • Heating Function in Cold Climates: If operating in cold environments, utilize the optional heating function to maintain optimal battery temperature, which significantly improves battery life and performance.
  • Communication Protocols: For advanced integration with inverters or other systems, ensure the correct RS485 or CAN protocol is selected and configured in the APP.

8. Support

For any inquiries, technical support, or customized feature requests, please contact JIKONG customer service. You can reach Chengdu Jikong Technology Co.LTD via the contact information provided below:

  • Phone/WhatsApp: +86 13068721990
  • Email: jasonliu@jk-smartbms.com
Image showing optional functions with letter identifiers and contact information for customized features.
Figure 13: Optional Functions and Contact for Customization

Please refer to the official JIKONG website or contact support for the most up-to-date warranty information.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.