ESSGOO 7018 MP5 Player

Contents

ESSGOO 7" Double 2 DIN Car Stereo User Manual

Model: 7018 MP5 Player

ESSGOO 7 inch Double 2 DIN Universal Radio

Overview of the ESSGOO 7-inch Double 2 DIN Universal Car Stereo.

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your ESSGOO 7" Double 2 DIN Car Stereo. Please read this manual thoroughly before use to ensure proper functioning and to prevent damage.

1.1. Important Safety Information and Warnings

  • Professional Installation Recommended: It is highly recommended that the machine be installed by a car audio professional.
  • Power Supply: This unit is designed for a 12V vehicle power supply system (grounding wire required). Do NOT install in a 24V vehicle, as it will cause damage.
  • Fuse Replacement: Do not repair or replace the power fuse without professional guidance. Improper use of the fuse can damage the machine or cause a fire.
  • Driving Safety: To avoid violating traffic laws and unnecessary accidents, drivers must not watch videos or operate the machine while driving.
  • Environment: Avoid placing this product in humid environments or near water to prevent electric shock, fire, or other damage.
  • Pre-Energization Note: To prevent burning out the machine, do not energize until you have correctly connected the power cord.
  • Small Parts: The product contains small parts. Keep out of reach of children to prevent swallowing.

2. Setup and Installation

2.1. Pre-Installation Test

Before full installation, perform a quick test to ensure the device is functioning correctly. If the unit does not work after installation, recheck these steps.

  1. Combine the red and yellow wires of the car stereo and connect them to the positive pole of a 12V battery.
  2. Connect the black wire to the negative pole of the battery.
  3. After 2 seconds, check if the car stereo screen lights up. If it does, the unit is functioning properly.

2.2. Installation Methods

There are three common installation methods. Choose the one that best suits your vehicle. You may also re-install the new radio using the method of the original car radio.

  • Screw-fixed installation
  • Card position fixed installation
  • Special frame fixed installation
Diagram showing three installation methods: screw-fixed, card position fixed, and special frame fixed.

Illustration of different installation types for the car stereo.

2.3. Important Installation Notes

The product can be installed in vehicles with dashboard dimensions of 178*100 mm. If your car dashboard size is NOT 178*100mm, you will need an extra installation kit (not included) to install the unit.

Diagram showing car dashboard dimensions and the need for an installation kit if the size is not 178x100mm.

Dashboard dimension check for installation.

The product's power cord is ISO standard. Ensure your original car radio's power cord is an ISO connector. If not, an additional adapter cable (not included) will be needed.

Image showing an ISO connector and a note about needing an adapter if the original car radio does not have an ISO connector.

ISO connector compatibility note.

2.4. Wiring Diagrams

Refer to the following diagrams for proper wiring connections.

2.4.1. Main Harness Wiring

Main wiring harness diagram with labels for FR-, FR+, FL-, FL+, RR-, RR+, RL+, RL-, KEY1, BACK, ACC, GND, B+, ILL, KEY2, ANT.POWER.

Main harness connections for power and speakers.

Main Harness Connections
Wire Color/LabelFunction
FR-, FR+Front Right Speaker
FL-, FL+Front Left Speaker
RR-, RR+Rear Right Speaker
RL+, RL-Rear Left Speaker
KEY1, KEY2Steering Wheel Control Input
BACKReverse Trigger Line
ACCAccessory Power (Switched 12V)
GNDGround
B+Battery Positive (Constant 12V)
ILLIllumination
ANT.POWERAntenna Power Output

2.4.2. Back Interface Diagram

Back interface diagram showing ports for Power Cable, RCA Input/Output, Canbus serial cable, 2USB Cable, Camera Input, Radio antenna, GPS Antenna.

Rear panel connections for various inputs and outputs.

  1. Power Cable
  2. RCA Input/Output
  3. Canbus serial cable
  4. 2 USB Cable
  5. Camera Input
  6. Radio antenna
  7. GPS Antenna

2.4.3. Rear View Camera Wiring (Optional)

If you are using a rear view camera, connect the reversing trigger line to the BACK (A6) wire in the power harness. The red wire from the camera connects to the positive pole of the reverse light cable, and the camera power cable connects to the camera power source. The video output from the camera connects to the Camera Input on the back of the unit.

Rear view camera wiring diagram showing connections for reversing trigger line, camera power, and video input.

Wiring diagram for optional rear view camera. Note: Connect the rear view wire even if not using a camera, otherwise WiFi and Bluetooth signals may suffer.

3. Operation

3.1. Machine Host Controls

Front Panel Controls
SymbolDescription
MICBuilt-in microphone hole
RSTReset (press with a sharp object)
Power Icon (circle with vertical line)Press and hold for 3 seconds to power off. Short press repeatedly to mute or unmute.
Home Icon (house)Go to main menu
Return Icon (U-turn arrow)Return to the previous interface
Volume Up (+)Press or hold repeatedly to increase volume
Volume Down (-)Press or hold repeatedly to decrease volume
Front panel buttons and rear connection ports diagram.

Detailed view of the front panel buttons and their functions.

3.2. On-Screen Main Interface Icons

The main interface may vary slightly between products. Refer to the specific product for exact details.

Main Interface Icons
IconNameOperation
Square with three linesMain menuTouch to switch screen to main menu
Up arrowHide shortcut menuTouch to hide the shortcut menu button area
Two overlapping squaresBackstageTouch to show all programs running in the background
U-turn arrowReturnTouch to switch screens to return to previous screen
Gear iconSettingTouch to enter settings
Grid of squaresApplicationTouch to enter more app interface
Compass iconNavigationTouch to enter navigation
User interface examples showing various icons for apps and functions.

Examples of the car stereo's user interface.

3.3. Drop-Down List Icons

Drop-Down List Icons
IconNameOperation
Wi-Fi symbolWi-FiTurn on/off Wi-Fi
Bluetooth symbolBluetoothTurn on/off Bluetooth
Sun/Moon iconScreen offOpen/Close Screen
Camera iconScreenshotTouch to take a screenshot
Car icon with gearCar settingTouch to enter car setting
Broom iconClean-upTouch to clean
Monitor with arrowVideo outTouch to set Video out
Optical disc iconOPTICALTurn on/off OPTICAL

3.4. APP Icons

APP Icons and Functions
IconNameOperation
Bluetooth symbolBTTouch into Bluetooth
Voice iconESSGOO VoiceTouch to enter smart voice settings
Star with voice iconESSGOO +Touch to enter the intelligent voice software
DAB+ iconDAB+Touch to enter DAB+
Map pin iconHERE WeGoTouch to enter offline map
Car iconCar setTouch to enter car settings
Gear icon with carCar SettingsTouch to enter settings, enter password 000000 for factory settings
Google Maps iconMapsTouch to enter Google Map online
Phone icon with linkPhonelink/TIMATouch to connect to mobile phone
Video play iconVideoTouch to enter video playback
Folder iconFilemanagerTouch to enter file management

3.5. Radio Function

The radio interface allows you to tune into FM stations, save presets, and adjust audio settings.

FM Radio interface showing frequency display, station presets, and control buttons.

FM Radio interface with frequency range 87.5-108 MHz.

  1. Band Switch: Click to switch between FM1, FM2, FM3 bands.
  2. Mute: Click to mute/unmute audio.
  3. Previous/Next Station: Click to switch stations. Long press to search up/down.
  4. Search: Click to search for stations. Long press to search and save stations.
  5. Near/Far: Switch between near and far stations.
  6. Audio Effects: Enter DSP settings interface.
  7. RDS: Enable/disable RDS functionality.
  8. Reception Status: Displays current radio reception status.
  9. Fine Tuning: Adjust reception frequency forward/backward.
  10. Station List: Switch stations. Long press to save current station.

3.6. Bluetooth Function

Built-in Bluetooth allows connection to mobile phones for hands-free calling and music playback. Supports phonebook download.

Bluetooth function interface showing phone dialing and music playback.

Bluetooth interface for calls and music.

3.6.1. Bluetooth Connection Interface

  • Dialing: Enter Bluetooth dialing.
  • Contacts: Display phone's contact list (manual refresh/sync required).
  • Call History: Display current call history.
  • Pairing Connection: Display connected and paired devices.
  • Bluetooth Settings: Enter Bluetooth settings (name, auto-answer, etc.).

3.6.2. Bluetooth Phone

  • Search: Search for nearby Bluetooth devices.
  • Connect: Connect to selected Bluetooth device.
  • Disconnect/Delete: Disconnect/delete from connected Bluetooth device.

3.6.3. Bluetooth Settings Interface

  • Auto Answer: Turn on to automatically answer incoming calls.
  • Auto Connect: Turn on to automatically connect to paired mobile phones.
  • Bluetooth Network: Turn on to share mobile phone data traffic after connecting to Bluetooth.

3.6.4. Bluetooth Call Interface

  • Call Switching: Switch between car and mobile phone call statuses.
  • Hang Up: End current call.
  • Dial: Enter dial interface.

3.6.5. Bluetooth Music

  • Previous Song: Switch to previous song.
  • Play/Pause: Play/pause music.
  • Next Song: Switch to next song.

3.7. CarPlay and Android Auto

Seamlessly integrate your smartphone for calls, messages, navigation, and music.

CarPlay wired connection interface showing iPhone connected to car stereo.

CarPlay wired connection.

Android Auto wired connection interface showing Android phone connected to car stereo.

Android Auto wired connection.

3.7.1. CarPlay Connection

  • Wireless: Turn on Wi-Fi and Bluetooth on your iPhone. Go to Settings > General > CarPlay > Click "Essgoo-BT" > Pair > Connect.
  • Wired: Connect your iPhone to the USB port of the device using a data cable. Follow prompts on your phone to enable CarPlay. (Use original phone cable for stable connection).
  • Siri Voice Control: Siri voice control must be enabled on your iPhone for in-car CarPlay functionality.
  • Troubleshooting: If CarPlay interface doesn't appear, click the "ZLINK" icon on the car display.

3.7.2. Android Auto Connection

  • Wireless: Turn on Wi-Fi and Bluetooth on your Android phone. Pair with the car's Bluetooth. Follow prompts to pair and confirm to enable Android Auto.
  • Wired: Connect your Android phone to the USB port of the device using a data cable. Follow prompts on your phone to enable Android Auto. (Use original phone cable for stable connection).
  • Troubleshooting: If Android Auto interface doesn't appear, click the "ZLINK" icon on the screen.

Important Notes for Wireless Connectivity:

  • When using wireless connectivity, Bluetooth on your phone will show as disconnected, and Wi-Fi will show as off. This is normal. The feature switches to a local area network connection, preventing connection to other Wi-Fi networks.
  • Wireless connectivity supports navigation, music, and radio apps only. Video apps are not supported. Compatibility may vary by phone/system manufacturer.
  • Connection methods may vary due to the wide variety of Android phone brands and customization. Follow prompts on your phone.

Mirror Link allows you to synchronize your phone's screen with the car stereo display. This is compatible with both Apple and Android phones.

Mirrorlink function showing an iPhone and Android phone screen mirrored to the car stereo display.

Mirrorlink function for screen projection.

3.8.1. Icon Function Description

  • Mirror: Switch to mirror screen projection function.
  • Settings: Enter ZLINK settings to configure driver's seat/background connection.

3.8.2. Screen Mirroring Switch

  • Switch between wired and wireless screen mirroring.
  • Interconnection: Switch back to CarPlay/Android Auto mode.

3.8.3. Wireless Screen Mirroring (iOS)

Follow on-screen prompts to connect to your phone's hotspot and turn on the mirroring switch on your phone.

3.8.4. Android Screen Mirroring (zPLUS App)

Download and install the "zPLUS" app on your phone. Scan the QR code on the screen to download and install the app, then follow the on-screen instructions.

3.9. Digital Sound Processor (DSP)

The DSP allows for advanced audio adjustments.

  • DSP Switch: Enable/disable DSP audio effects.
  • EQ: Adjust equalizer effects manually.
  • Sound Effects: Set surround sound and equalization.
  • Ultra-Bass: Adjust ultra-bass settings.
  • ASP: Select built-in sound effects and adjust manually.
  • Balance: Adjust sound field balance and listening area.

3.10. Media Playback (Local Music & Videos)

Play music and videos from your device or connected USB/TF card.

Multimedia system interface showing options for USB, TF card, AUX input, and Bluetooth.

Multimedia system inputs.

3.10.1. Local Music

  • Loop Playback: Switch between random, sequential, and loop playback.
  • Previous/Next Track: Switch songs.
  • Play/Pause: Play or pause music.
  • Playlist: View music list on device or USB.
  • Sound Effects: Enter DSP settings.

3.10.2. Local Videos

  • Loop Playback: Toggle between random, sequential, and loop playback.
  • Aspect Ratio: Switch playback screen aspect ratio.
  • Previous/Next Video: Switch videos.
  • Play/Pause: Play or pause video.
  • Playlist: View video list on device or USB drive.
  • Sound Effects: Enter DSP settings.

3.11. Map Navigation

Access navigation features for easy travel.

3.11.1. Google Maps Interface

  • Search box: Open search box and keyboard.
  • Surroundings: Display services around current location.
  • Type: Switch map type and route mode.
  • Location: Display current location.
  • Navigation: Open destination search box.
  • Personal center: Perform personalized settings after logging in.

3.11.2. WAZE Interface

  • Search box: Access search box, swipe up for quick bar.
  • Location: Display current location.
  • Menu: Enter settings.
  • Search Box: Display keyboard and enter destination.
  • Shortcut: Set home and company locations.

3.12. Steering Wheel Button Learning (SWC)

Configure your car's steering wheel buttons to control the stereo.

Steering wheel control learning interface showing button mapping options.

Steering Wheel Control setup screen.

  1. Control Type: Switch to "Learning" mode.
  2. Control: Enter the control learning operation interface.
  3. Click the function icon you wish to learn (e.g., Volume +) on the screen.
  4. Follow on-screen prompts and press the corresponding button on the steering wheel.
  5. After learning all buttons, click "Return" to exit and save settings.

Notes:

  • Pull-up Resistance: If buttons cannot be saved (20K mode) or after learning, click the icon to switch and re-learn.
  • Reset: Clear saved button records.
  • This function applies to models with steering wheel control buttons that do not have CAN-BUS.

3.13. In-Vehicle Settings

  • General Settings: Radio, rearview, square control, reverse assist lines.
  • Display Settings: Screen saver, wallpaper, brightness.
  • Sound Settings: Navigation, media, Bluetooth volume.
  • Factory Settings: Less common settings (password is 000000).
  • System Information: Host configuration and version.

3.14. Colorful Button Lights

Customize the button light colors.

Colorful button lights showing various color options.

Customizable colorful button lights.

  • Display: Enter display settings.
  • Colorful Lights: Enter colorful lights settings interface.

3.15. Touch Calibration

If touch abnormalities occur (deviation, reverse touch, no touch), perform calibration:

  1. After normal boot-up, press and hold the touch screen with five fingers.
  2. Wait 5 seconds, then slightly move fingers to enter the touch calibration interface.
  3. Follow on-screen prompts to click the screen cursor in sequence. System returns to main interface after calibration.

3.16. Theme Selection

Select your preferred theme from the available options.

  • Select your preferred theme.
  • Click OK to switch.

3.17. File Manager

Manage files on USB devices.

  1. USB Device: Click to open USB device and view files.
  2. Copy: Select file, long-press name, context menu appears. Click to copy.
  3. Share, Cut, Delete: Options available in the context menu.
  4. Root Directory: Click main directory icon to return to root directory.
  5. Save: Select directory to save files.
  6. Paste: Click "Paste" to copy files to directory.

4. Specifications

Product Specifications
FeatureDetail
SystemWINCE
Screen Size7 inch HD screen
Screen Resolution1024*600
Radio Frequency87.5-108MHz
Radio BandsFM1, FM2, FM3 (18 pre-store stations)
Reversing SupportYes
Bluetooth Version5.1
Remote ControlYes
Audio FormatsMP3, WMA, WAV, FLAC, OGG, APE (CD level quality for APE)
Video FormatsRM, RMVB, DVD (VOB), VCD (DAT), MP1, MP2, DIVX/XVID/MP4, H263, H264, FLV, MKV, 3GP, SWF, AVI, ASF, MJPEG
Image FormatJPEG
Function SupportMP5, Reverse, Bluetooth, Mobile Phone Interconnection, Wired & Wireless CarPlay, Wired & Wireless Android Auto
Installation Size100*178MM (Double DIN)
Working VoltageDC 12 V
Max Output Power4 x 60W
InterfaceUSB, AUX, Memory Card
Tuner TypeFM
Warranty1 Year
CertificationCE, FCC
MaterialPlastic

5. Troubleshooting

This section addresses common issues you might encounter. For more detailed solutions, refer to the full user manual PDF or the ESSGOO+ intelligent voice system's Q&A section.

  • Unit does not power on after installation: Recheck the pre-installation test steps and all wiring connections, especially power and ground. Ensure the 12V battery connection is secure.
  • No sound: Check speaker wiring, volume levels, and DSP settings. Ensure mute is not activated.
  • Touch screen unresponsive or inaccurate: Perform touch calibration as described in section 3.15.
  • CarPlay/Android Auto not connecting:
    • For wired connection, use the original phone data cable.
    • For wireless, ensure Wi-Fi and Bluetooth are enabled on your phone and correctly paired.
    • Check if Siri voice control is enabled on iPhone for CarPlay.
    • If the interface doesn't appear, tap the "ZLINK" icon on the car stereo.
  • Poor WiFi/Bluetooth signal: Ensure the rear view camera wire is connected, even if not using a camera, as this can affect signal strength.
  • Steering Wheel Control buttons not saving/working:
    • Ensure the unit is in "Learning" mode during configuration.
    • If buttons cannot be saved in 20K mode, try switching the pull-up resistance value and re-learning.
    • This function is for vehicles without CAN-BUS.

6. User Tips

  • For optimal performance with CarPlay/Android Auto, always use your phone's original USB data cable for wired connections.
  • If you experience any issues with wireless CarPlay/Android Auto, try restarting both your phone and the car stereo.
  • The "ESSGOO+" intelligent voice system can be activated by saying "Hey TOP". Log in with your Google or Facebook account to access product introductions and operation videos.
  • Remember to connect the rear view camera wire even if you don't have a camera to avoid potential WiFi and Bluetooth signal interference.

7. Warranty and Support

Your ESSGOO car stereo comes with a 1-year warranty.

7.1. Privacy Protection

To understand how your personal information is protected, please visit the ESSGOO privacy policy page: https://essgoo.com/pages/privacy-policy.

7.2. EU Declaration of Conformity

This device complies with the essential requirements and other relevant provisions of Directives 2014/30/EU and 2014/53/EU. A copy of the EU Declaration of Conformity is available online: https://essgoo.com/pages/doc.

You can scan the QR code below to access the URL and view the Doc file:

QR code for EU Declaration of Conformity is not available in ALLOWED_URLS, please refer to the link above.

7.3. Contact Information

For any further questions or support, please contact ESSGOO customer service.

  • Email: support@essgoo.com
  • Official Website: www.essgoo.com
  • Phone (United States): +1 2065363281
  • Phone (Germany): +49 8001014317
  • Phone (United Kingdom): +44 1518080196

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.