FLIPSKY 75133 Motor

Contents

Flipsky 75133 Waterproof Brushless DC Motor

User Manual

1. Introduction

Thank you for choosing the Flipsky 75133 Fully Waterproof Brushless DC Motor. This high-performance motor is designed for demanding applications such as surfing boats, underwater thrusters, efoils, ejet boards, and hydrofoils. Its robust construction and waterproof rating ensure reliable operation in marine environments. This manual provides essential information for the safe and efficient setup, operation, and maintenance of your motor.

Flipsky 75133 waterproof brushless DC motor with power cables.

Front view of the Flipsky 75133 motor, showcasing its compact design and integrated power cables.

2. Safety Information

Please read and understand all safety warnings before operating the motor. Failure to follow these instructions may result in property damage, serious injury, or death.

  • High Voltage: This motor operates at high voltages. Always exercise extreme caution when working with electrical components.
  • Professional Installation: Installation and wiring should ideally be performed by qualified personnel.
  • Disconnect Power: Always disconnect all power sources before performing any installation, maintenance, or inspection.
  • Moving Parts: Keep hands, hair, loose clothing, and tools clear of the motor shaft and propeller during operation.
  • Insulation: Ensure all electrical connections are properly insulated to prevent short circuits and water ingress.
  • Overheating: Do not operate the motor beyond its specified limits. Monitor temperature during initial runs.

3. Package Contents

Please check the package contents upon receipt:

  • Flipsky 75133 Waterproof Brushless DC Motor with integrated 10AWG lead wires and 8mm lantern plugs.

Note: Electronic Speed Controller (ESC), propeller, and mounting hardware are typically sold separately.

4. Specifications

FeatureSpecification
Voltage Range6~16S
KV (RPM/V)120KV
Rated Current63A
Maximum Current110A
Rated Power3800W
Maximum Power6600W
No Load Current7.4A
Number of Slots & Poles12N/14P
Motor Dimensions (Φ×L)Φ75.0×L133.0 mm
Shaft DiameterΦ11.8 mm
Lead Wire Gauge10AWG
Coil Resistance0.05Ω
Coil Inductance0.1mH
Lead Wire Length1300mm
Connector Type8mm lantern plug
Maximum Thrust40.1kgf
Insulation Voltage & Leakage Current500VAC/50HZ/1MA/3S
Maximum Operating Temperature120℃
Waterproof LevelIP68
Weight2.35kg

5. Setup

5.1. Mounting

Refer to the motor diagram for precise mounting dimensions and hole patterns. Ensure the motor is securely fastened to a rigid structure using appropriate hardware.

  • The motor features various mounting points, including 4-M5*8, 4-M5*7, and 6-Φ4.30 holes spaced at 60° intervals.
  • Use corrosion-resistant fasteners suitable for your application environment.
  • Ensure adequate clearance around the motor for any attached propeller or guard.
Detailed technical drawing of the Flipsky 75133 motor with all dimensions and mounting points.

This diagram provides precise measurements for the motor's length (133mm), diameter (75mm), shaft diameter (11.8mm), and various mounting hole patterns (e.g., 4-M5*8, 4-M5*7, 6-Φ4.30 at 60° spacing). It also shows the 10AWG lead wires and 8mm lantern plugs.

5.2. Wiring

The motor comes with three 10AWG lead wires terminated with 8mm lantern plugs. These are standard 3-phase connections for brushless DC motors.

  • Connect the motor's three wires to the corresponding output phases of a compatible Electronic Speed Controller (ESC).
  • Ensure all connections are secure and properly insulated to prevent short circuits, especially in wet environments.
  • Observe proper polarity when connecting the ESC to your battery pack.

5.3. Propeller Attachment

Attach a compatible propeller to the motor shaft (Φ11.8 mm). Ensure the propeller's bore matches the shaft diameter and that it is securely fastened.

  • Align the propeller correctly on the shaft, ensuring it is fully seated.
  • Use any provided nuts, washers, or set screws to firmly secure the propeller. Apply thread-locking compound if recommended by the propeller manufacturer.
  • Verify that the propeller spins freely without wobbling or hitting any part of the motor or mounting structure.
Technical drawing of a 152mm (6-inch) 3-blade propeller with dimensions.

This diagram illustrates the dimensions of a compatible 152mm (6-inch) 3-blade propeller, including its diameter, pitch, and bore size (Φ12.10) for shaft attachment.

5.4. Propeller Guard (Optional)

If using a propeller guard, ensure it is compatible with your propeller and motor setup, and securely mounted.

Technical drawing of a propeller guard with dimensions.

This diagram shows the design and dimensions of a propeller guard, indicating how it might enclose the propeller for safety and protection.

6. Operating Instructions

  • Power On: Connect your battery to the ESC. The ESC should initialize.
  • Throttle Control: Gradually increase throttle input from your control system. Avoid sudden full-throttle applications, especially with heavy loads.
  • Voltage Range: Ensure your power supply (battery) is within the specified 6-16S voltage range.
  • Temperature Monitoring: During initial runs and under heavy load, periodically check the motor's temperature. While the motor is rated for 120℃, prolonged operation at extreme temperatures can reduce lifespan.
  • Water Cooling: Although the motor is waterproof, ensure adequate water flow or cooling if operating in an enclosed thruster housing to prevent heat buildup.

7. Maintenance

  • After Use (Saltwater): If used in saltwater, thoroughly rinse the motor with fresh water immediately after use to prevent salt buildup and corrosion.
  • Visual Inspection: Regularly inspect the motor for any signs of physical damage, such as dents, cracks, or corrosion. Check the propeller for damage.
  • Cable Integrity: Inspect the motor's lead wires and connectors for fraying, cuts, or loose connections.
  • Shaft and Bearings: Check the motor shaft for any bends or damage. Listen for unusual noises during operation that might indicate worn bearings.
  • Cleaning: Keep the exterior of the motor clean and free from debris.

8. Troubleshooting

ProblemPossible CauseSolution
Motor not spinningNo power to ESC; ESC not initialized; Faulty ESC; Disconnected motor wires; No signal from controller.Check battery connection and charge; Re-power ESC; Test ESC with another motor; Check motor wire connections; Verify controller signal.
Reduced performance / OverheatingPropeller obstruction/damage; Incorrect voltage/current; ESC settings incorrect; Motor overloaded; Insufficient cooling.Clear obstructions, replace damaged propeller; Verify battery voltage and current capacity; Adjust ESC settings; Reduce load; Ensure adequate cooling.
Unusual noise / VibrationLoose propeller; Damaged bearings; Bent shaft; Foreign object in motor; Unbalanced propeller.Tighten propeller; Inspect/replace bearings; Check shaft for straightness; Remove foreign objects; Balance or replace propeller.

9. User Tips

  • Voltage for Max Power: For optimal performance and to achieve the maximum rated power of 6600W, ensure your power supply operates at the higher end of the recommended 6-16S voltage range (e.g., 48V to 60V). Refer to the thrust test data for performance at various voltages.
Table showing thrust test results for the 75133 motor at various voltages, currents, speeds, and duty cycles.

This table presents comprehensive thrust test data. It details performance metrics such as load current (A), power (W), speed (RPM), duty cycle (%), thrust in kgf, and thrust in N across different operating voltages (36V, 42V, 48V, 54V, 60V). For example, at 60V and 90A, the motor achieves 5400W power, 2443 RPM, 56.70% duty cycle, and 40.1 kgf (393.0 N) of thrust.

10. Warranty and Support

10.1. Warranty Policy

The warranty period for consumable electronic products (e.g., VESC/Motor/Battery) is guaranteed for 2 months from the 7th day after shipment (the shipping date is checked by logistic record). Please contact Flipsky service for any warranty claims.

If you return an item, it is for free repair or replacement when we get it and analyze it as a manufacturing failure. We will bear the return back to you shipping cost only. If the replacement or repair is not possible for you, a discount can be provided for the new replacement (excludes the shipping cost).

The following conditions are NOT covered by the above warranty:

  • Cannot provide purchase channel source proof.
  • Mechanical damage to electronic components or PCB.
  • PCBA board has repair soldering iron traces (excluding the solder cable bullet connectors).
  • Wire damage or external impact damage.
  • Water inflow (for non-waterproof products).
  • Abnormal applications beyond the product specifications.

Most products are tested before shipment. Any uncertain connection or information for VESC/Motors settings, please contact us before your installation. No term warranty, in no case shall Flipsky's liability be greater than the actual purchase price of the product.

On the shipping way product orders cannot be canceled unless the extra shipping cost is agreed to be charged.

We're willing to provide repair service for reasonable charge if your product is out of warranty, while the service excludes both sides' shipping cost.

10.2. Support

For technical support, warranty claims, or any other inquiries, please contact Flipsky directly:

Email: flipsky_service@outlook.com

© 2023 FLIPSKY. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.