intelamp YL002-12A

Contents

Intelamp Outdoor Solar Light User Manual

Model: YL002-12A

1. Product Information

Product Name: Solar Lamp

Model: YL002-12A

Manufacturer: Shenzhen Jindian Electronic Technology Co., Ltd, No. 9, Tianyang 1st Road, Datianyang Industrial Zone, Dongfang Community, Songgang Street, Bao'an District, Shenzhen City, Guangdong Province.

EU Authorized Representative: SUCCESS COURIER SL, CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain.

2. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements.

3. Setup and Installation

The Intelamp Outdoor Solar Light is designed for easy, self-contained installation.

3.1. Preparation

  1. Remove all protective films from the solar light casing and solar panel.
  2. Ensure the solar panel is unobstructed and free of stains for optimal performance.

3.2. Choosing an Installation Location

Install or place the light fixture in a well-lit, unobstructed location. The solar panel requires direct sunlight exposure for efficient charging. Avoid shaded areas.

Recommended Installation Height: 1.8 - 2.5 meters (approximately 6 - 8 feet).

3.3. Mounting Options

Each package includes screws and tie straps for versatile installation.

  • Screw Fixation: The solar sensor light can be screwed to hard surfaces such as walls, wooden fences, and garage door frames.
Solar light mounted with screws on a wall
Figure 1: Screw fixation for wall mounting.
  • Cable Tie Fixation: The light can be bound to trees or posts using the provided tie straps.
Solar light attached to a tree with cable ties
Figure 2: Cable tie fixation for tree or post mounting.

3.4. Adjusting Lamp Heads and Solar Panel

The light features an adjustable and flexible design to optimize lighting coverage and solar charging.

  • Middle Lamp Head: Can be adjusted vertically (up and down) by 45 degrees.
  • Side Lamp Heads: Can be adjusted horizontally (left to right) by up to 90 degrees.
  • Solar Panel: Can be adjusted vertically (up and down) by 60 degrees. The optimum tilt angle is usually 20 degrees to make the most efficient use of available sunlight and to allow rainwater to remove any dust build-up efficiently.
Diagram showing adjustable lamp heads and solar panel angles
Figure 3: Adjustable lamp heads and solar panel.

4. Operating Instructions

4.1. Initial Charging

No manual charging is required. Place the light fixture in direct sunlight. The solar panel will automatically absorb sunlight and store electrical energy. 6-8 hours of sufficient sunlight can provide 8-12 hours of nighttime lighting (actual duration depends on weather and sunlight intensity).

Solar light on a tree showing 4 hours charging for 24 hours lighting
Figure 4: Charging and lighting duration.

4.2. Power On/Off

Locate the power switch on the side/bottom of the light fixture and switch it to the


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.