ESSGOO AR9001

Contents

ESSGOO Android 15 Car Stereo Radio User Manual

Model: AR9001

For BMW X3 E83 (2006-2010)

1. Introduction

1.1. Tips and Warnings

To emphasize important information in this manual, special attention should be paid to labels indicating warnings and reminders.

Important Tips

  • Please read all instructions before installation. Professional car audio installation is recommended.
  • This machine is suitable for a vehicle 12V power supply system (grounding wire is required). Do not install in a 24V vehicle, as it will damage the machine.
  • Do not repair the power fuse without professional guidance. Improper fuse use can damage the machine or cause fire.
  • To avoid violating traffic rules, drivers must not watch videos or operate the machine while driving to prevent accidents.
  • For safety and normal product use, invite professionals to install, disassemble, or repair the machine to avoid damage and accidents.
  • Avoid placing this product in a humid environment or near water to prevent fire due to electric shock or other damage.

Note: To prevent burning out the machine, do not energize until you have connected the power cord correctly!

The product contains small parts. Keep out of reach of children to prevent swallowing!

1.2. Pre-Installation Test

Perform a quick test before installation to confirm normal device operation. If the unit fails after installation, recheck the steps.

Test Procedure:

  1. Combine the red and yellow wires of the car stereo and connect them to the positive pole of a 12V battery.
  2. Connect the black wire to the negative pole of the battery.
  3. After 2 seconds, check the car stereo. If the screen lights up, the car stereo is functioning properly.

2. Setup

2.1. Installation Methods

There are three ways to install the machine. Choose one based on your actual situation. You can also re-install the new radio according to the original car radio's installation method.

  1. Screw-fixed installation
  2. Card position fixed installation
  3. Special frame fixed installation
Diagram showing three different car stereo installation methods: screw-fixed, card position fixed, and special frame fixed.
Figure 2.1: Three common installation methods.

2.2. Wiring Harness

Note: The picture is for reference only; please refer to the actual product.

Diagram of the main wiring harness with labeled connections for power, ground, steering wheel controls, and audio outputs.
Figure 2.2: Main Wiring Harness Connections
Harness Connections
Wire Label Function
FR-, FR+Front Right Speaker
FL-, FL+Front Left Speaker
RR-, RR+Rear Right Speaker
RL-, RL+Rear Left Speaker
KEY1, KEY2Steering Wheel Control Input
BACKReverse Trigger Line
ACCAccessory Power (Switched +12V)
GNDGround
B+Battery Power (Constant +12V)
ILLIllumination
ANT.POWERAntenna Power Output

2.3. Back Interface Diagram

Diagram of the car stereo's rear panel showing various input/output ports labeled numerically.
Figure 2.3: Rear Interface Ports
  1. Power Cable
  2. RCA Input/Output
  3. Canbus Serial Cable
  4. 2USB Cable
  5. Camera Input
  6. Radio Antenna
  7. GPS Antenna

2.4. Rear View Camera Wiring (Optional)

Components: Monitor (Not Included), Camera Power Source, Camera (Optional).

Wiring diagram for a rear view camera, showing connections to the car stereo's reversing trigger line, camera power, and video input.
Figure 2.4: Rear View Camera Wiring

Wiring Instructions:

  • Reversing Trigger Line: Connect this wire to the reversing line in the power harness (e.g., Back (A6)).
  • Camera Power: Connect the red wire to the positive pole of the reverse light cable. Connect the black wire to GND and the reversing light cable.
  • Video Output: Connect the camera's video output to the car stereo's camera input.

NOTE: Whether you are using a rear view camera or not, please connect the rear view wire. Otherwise, your WiFi and Bluetooth signals will suffer!

3. Operating Instructions

3.1. Machine Host Icon Introduction

Machine Host Controls
Symbol Operations & Controls
MICBuilt-in microphone hole
RSTReset (press with a sharp object)
Power IconPower on device. Press and hold for 3 seconds to power off. Short press repeatedly to mute or unmute.
Home IconTo main menu
Return IconReturn to the previous interface
Volume +Press or hold repeatedly to increase volume
Volume -Press or hold repeatedly to decrease volume

3.2. On-Screen Main Interface Icons

Note: The main interface may differ for different products.

On-Screen Main Interface Icons
Icon Name Operations
Main Menu IconMain menuTouch to switch screen to main menu
Hide Shortcut Menu IconHide shortcut menuTouch to hide the shortcut menu button area
Backstage IconBackstageTouch to show all programs running in the background
Return IconReturnTouch to switch screens to return to previous screen
Setting IconSettingTouch To Enter Settings
Application IconApplicationTouch To Enter More App Interface
Navigation IconNavigationTouch To Enter Navigation

3.3. On-Screen Drop-Down List Icons

On-Screen Drop-Down List Icons
Icon Name Operations
Wi-Fi IconWi-FiTurn on/off Wi-Fi
Bluetooth IconBluetoothTurn on/off Bluetooth
Screen Off IconScreen offOpen/Close Screen
Screenshot IconScreenshotTouch to take a screenshot
Car Setting IconCar settingTouch to enter Car setting
Clean-up IconClean-upTouch to clean
Video Out IconVideo outTouch to set Video out
OPTICAL IconOPTICALTurn on/off OPTICAL

3.4. On-Screen APP Icons

Note: If an APP is included in the product, an additional accessory must be purchased if it is to be used!

On-Screen APP Icons
Icon Name Operations
BT IconBTTouch into bluetooth
ESSGOO Voice IconESSGOO VoiceTouch to enter smart voice settings
ESSGOO+ IconESSGOO +Touch to enter the intelligent voice software
DAB+ IconDAB+Touch to enter DAB+
HERE WeGo IconHERE WeGoTouch to enter offline map
Car Set IconCar setTouch to enter car settings
Car Settings IconCar SettingsTouch to enter settings, enter password 000000 for factory settings
Maps IconMapsTouch to enter google map online
Phonelink/TIMA IconPhonelink/TIMATouch to connect to mobile phone
Video IconVideoTouch to enter video playback
Filemanager IconFilemanagerTouch to enter file management

3.5. Intelligent Voice - ESSGOO+ (Optional)

Activate by shouting: "Hey TOP". Specific voice commands can be found in the "instruction" interface. Log in to ESSGOO+ with your Google email or Facebook account to access product introductions, operation videos, and promotion products.

Screenshots of the ESSGOO+ intelligent voice service interface, showing voice commands and version information.
Figure 3.1: ESSGOO+ Intelligent Voice Interface

3.6. Main Interface Quick Bar

Quick Bar Operation Instructions:

  1. Long press an icon to delete the shortcut.
  2. Click the '+' sign to add a shortcut.
  3. Up to 5 shortcut icons can be displayed. Swipe left/right to switch if more than 5 icons are present.
Main interface of the car stereo showing a quick bar with various application shortcuts.
Figure 3.2: Main Interface with Quick Bar

3.7. Radio Function

Radio Icon Functions
Function Description
Band SwitchClick to switch bands.
MuteClick to mute.
Previous StationClick to switch to previous station / long press to search upward.
SearchClick to search for stations / long press to search and save stations.
Next StationClick to switch to next station / long press to search downward.
Near/FarClick to switch between near and far stations.
Audio EffectsClick to enter the DSP settings interface.
RDSClick to enable RDS functionality.
Reception StatusDisplays current radio reception status.
Fine TuningClick to adjust reception frequency forward/backward.
Station ListClick to switch stations / long press to save the currently playing station.

3.8. Bluetooth Connection Interface

Bluetooth Connection Icon Functions
Function Description
DialingEnter Bluetooth dialing.
ContactsDisplay phone's contact list (manual refresh/synchronization required).
Call HistoryDisplay current call history on car's infotainment system.
Pairing ConnectionDisplay connection interface, showing connected and paired devices.
Bluetooth SettingsEnter Bluetooth settings interface (name, auto-answer, etc.).
Bluetooth connection interface showing paired and available devices.
Figure 3.3: Bluetooth Connection Interface

3.9. Bluetooth Phone

  • Search: Click to search for nearby Bluetooth devices.
  • Connect: Click to connect to the currently selected Bluetooth device.
  • Disconnect: Click to disconnect from the currently connected Bluetooth device.
  • Delete: Click to disconnect from the currently connected Bluetooth device.

3.10. Bluetooth Settings Interface

Bluetooth settings interface showing options for auto answer, auto connect, and Bluetooth network.
Figure 3.4: Bluetooth Settings Interface
  • Auto Answer: Turn on this switch to automatically answer incoming calls.

3.11. Bluetooth Auto Connect & Network

  • Auto Connect: Turn on this switch to automatically connect to paired mobile phones.
  • Bluetooth Network: Turn on this switch to share mobile phone data traffic after connecting to mobile phone Bluetooth. (Click the exclamation mark on the left to view how to turn on mobile phone network sharing.)

3.12. Bluetooth Call Interface

Bluetooth Call Icon Functions
Function Description
Call SwitchingClick to switch between car and mobile phone call statuses.
Hang UpClick to hang up the current call.
DialClick to enter the dial interface.
Bluetooth call interface showing active call and dial pad options.
Figure 3.5: Bluetooth Call Interface

3.13. Bluetooth Music

Bluetooth Music Icon Functions
Function Description
Previous SongClick to switch to the previous song.
Play/PauseClick to play/pause music.
Next SongClick to switch to the next song.
Bluetooth music interface showing playback controls and song information.
Figure 3.6: Bluetooth Music Interface

3.14. CarPlay and Android Auto Connection Interface

CarPlay:

  1. Wireless connection: Turn on Wi-Fi and Bluetooth on your phone > Settings > General > CarPlay > Click Essgoo-BT > Pair > Connect.
  2. Wired connection: Use a phone data cable to connect your phone to the USB port of the installed device. Follow prompts on your phone to enable CarPlay. (Use original phone cable for stable connection).
  3. Siri voice control must be enabled on your phone for in-car CarPlay functionality.
  4. If the CarPlay interface does not appear, click the ZLINK icon on the in-car display screen.
CarPlay connection steps shown on phone and car stereo screens.
Figure 3.7: CarPlay Connection Steps

Android Auto:

  1. Wireless connection: Turn on your phone's Wi-Fi and Bluetooth settings > Pair with the car's Bluetooth > Follow prompts on your phone to pair > Confirm to enable Android Auto.
  2. Wired connection: Connect your phone to the USB port of the installed device using a phone data cable. Follow prompts on your phone to enable Android Auto. (Use original phone cable for stable connection).
  3. If the Android Auto interface does not appear on the screen, click the ZLINK icon on the screen.
Android Auto connection steps shown on phone and car stereo screens.
Figure 3.8: Android Auto Connection Steps

Important Notes on Wireless Connectivity:

  • When using wireless connectivity, Bluetooth on your phone may show as disconnected and Wi-Fi off. This is normal as it switches to a local area network connection.
  • Wireless connectivity supports navigation, music, and radio apps only. Video apps are not supported. Compatibility may vary by phone/system manufacturer.
  • Connection methods may vary between different Android phone brands due to system customization. Follow prompts on your phone.

3.15. Screen Mirroring

Icon Function Description:

  1. Mirror: Click to switch to mirror screen projection function.
  2. Settings: Click to enter ZLINK settings, where you can set driver's seat/background connection, etc.
Screen Mirroring interface showing options for wired and wireless mirroring.
Figure 3.9: Screen Mirroring Interface

Screen Mirroring Switch:

  1. Click to switch between wired and wireless screen mirroring.
  2. Click to switch back to CarPlay/Android Auto mode.

Wireless Screen Mirroring (iOS):

Follow on-screen prompts to connect to your phone's hotspot and turn on the mirroring switch on your phone.

3.16. DSP (Digital Sound Processor)

DSP Icon Functions
Function Description
DSP SwitchEnable/disable DPS audio effects.
EQSwitch to EQ adjustment interface to manually adjust EQ effects.
Sound EffectsSwitch to sound effects interface to set surround sound and equalization.
Ultra-BassSwitch to ultra-bass settings interface.
DSPSwitch to DSP settings interface.
ASPSwitch to ASP interface to select built-in sound effects and manually adjust them.
BalanceSwitch to sound field balance settings interface to adjust the listening area.
DSP interface showing equalizer and sound effect settings.
Figure 3.10: DSP Interface

3.17. Local Music

Local Music Icon Functions
Function Description
Loop PlaybackSwitch between random, sequential, and loop playback.
Previous TrackSwitch to the previous track.
Play/PausePlay or pause music.
Next TrackSwitch to the next track.
PlaylistView music list on device or USB.
Sound EffectsEnter DSP settings interface.
Local music playback interface showing song information and controls.
Figure 3.11: Local Music Interface

3.18. Local Videos

Local Video Icon Functions
Function Description
Loop PlaybackToggle between random, sequential, and loop playback modes.
Aspect RatioSwitch the aspect ratio of the playback screen.
Previous VideoSwitch to the previous video.
Play/PausePlay or pause the video.
Next VideoSwitch to the next video.
PlaylistView video list on device or USB drive.
Audio EffectsEnter DSP settings interface.
Local video playback interface showing video content and controls.
Figure 3.12: Local Videos Interface

3.19. Map Navigation

Google Maps Icon Functions:

Function Description
Search boxOpen search box and pop up keyboard.
SurroundingsDisplay services around current location.
TypeSwitch current map type and route mode.
LocationDisplay current location.
NavigationPop up destination search box.
Personal centerPerform personalized settings after logging in.
Google Maps navigation interface on the car stereo screen.
Figure 3.13: Google Maps Interface

Waze Icon Functions:

Function Description
Search boxEnter search box, swipe up to display quick bar.
LocationDisplay current location.
MenuEnter settings.
Waze navigation interface on the car stereo screen.
Figure 3.14: Waze Interface

3.20. Steering Wheel Button Learning

Operating Instructions:

  1. Control Type: Click to switch to "Learning" mode.
  2. Control: Click to enter the control learning operation interface.
  3. Function Icon: Click on the function icon you wish to learn (e.g., Volume +) on the screen.
  4. Press Button: Follow on-screen prompts and press the corresponding button on the steering wheel (e.g., Volume +).
  5. Save: After learning all buttons in sequence, click "Return" to exit and save the settings.
Steering wheel control learning interface showing various button functions and learning steps.
Figure 3.15: Steering Wheel Button Learning Interface

Notes:

  • Pull-up Resistance: If certain buttons cannot be saved during learning (20K mode) or after learning, click the icon to switch and re-learn.
  • Reset: Click to clear saved button records.
  • This function is applicable to all models with steering wheel control buttons that do not have CAN-BUS.

3.21. In-Vehicle Settings

Icon Function Description:

  • General Settings: Common functions like radio, rearview, square control, and reverse assist lines.
  • Display Settings: Screen saver, wallpaper, brightness, and other function settings.
  • Sound Settings: Navigation, media, and Bluetooth volume.
  • Factory Settings: Less common settings related to vehicle model CAN-BUS (password is 6 zeros).
  • System Information: Displays current host configuration and version information.

Colorful Lights (only available on certain models):

  • Display: Click to enter display settings.
  • Colorful Lights: Click to enter the colorful lights settings interface.

3.22. Touch Calibration

If touch abnormalities occur (deviation, reverse touch, no touch), follow these steps:

  1. After the car computer boots normally, press and hold the touch screen with five fingers.
  2. Wait 5 seconds, then slightly move your fingers to enter the touch calibration interface.
  3. Follow on-screen prompts to click the screen cursor in sequence. Once calibrated, the system will automatically return to the main interface.

3.23. Theme

Select your preferred theme and click OK to switch.

3.24. File Manager & Copy Method

File Copy Method:

  1. USB Device: Click to open the USB device and view files.
  2. Select File: Select the file to be copied, long-press its name, and a context menu will appear. Click 'Copy'.
  3. Share: Option to share the file.
  4. Copy: Option to copy the file.
  5. Cut: Option to cut the file.
  6. Delete: Option to delete the file.
  7. Root Directory: Click the main directory icon to return to the root directory of the file manager.
  8. Save Directory: Select the directory where you want to save the files.
  9. Paste: Click "Paste" to copy the files to that directory.

4. Specifications

Technical Specifications
Feature Detail
SystemAndroid 15
Screen9-inch 1280x720 HD Capacitive Touchscreen
CPU4x Cortex A53 1.5Ghz
Memory (RAM + ROM)2+32G / 2+64G / 4+64G
Radio BandFM
Radio FrequencyFM 87.5–108 MHz
Radio Data System (RDS)RT, AF, TA
Power Amplifier4 x 45 Watt MOSFET
Bluetooth4.1
Audio FormatsMP3, FLAC, APE, WMA, WAV, AAC, AMR
Video FormatsAVI, ASF, MP4, MOV, MPG, MPEG1/2/4, VOB, MKV, FLV, TS, WMV, RMVB, 3GP
OSD LanguageChinese (Simplified), Chinese (Traditional), Polish, Danish, German, Russian, Finnish, Dutch, Ukrainian, Spanish, Hungarian, Armenian, Italian, Yiddish, English
Operating Voltage12 V
Essgoo ModelAR9001
Warranty1 Year
CertificationCE, FCC
MaterialPlastic
Vehicle CompatibilityBMW X3 E83 (2006-2010)
Special FeaturesWiFi function, Support Can-Bus, Built-in GPS, MP3 players, CarPlay, Android Auto, Support steering wheel control

Note: If the original car has a DSP sound system, there will be no sound after installing our machine. Please do not purchase in this case.

5. Troubleshooting

  • No Sound After Installation: Check all wiring connections carefully. If your original car has a DSP sound system, this unit may not be compatible.
  • CarPlay/Android Auto Not Appearing: Ensure Siri is enabled on your iPhone for CarPlay. Click the ZLINK icon on the car stereo screen. For Android Auto, ensure your phone's prompts are followed correctly.
  • Wireless Connectivity Issues (Bluetooth/Wi-Fi): It is normal for Bluetooth to show as disconnected and Wi-Fi off when using wireless CarPlay/Android Auto, as the unit switches to a local network. Wireless features primarily support navigation, music, and radio apps, not video. Connection methods can vary significantly between different phone brands due to system customization.
  • Touch Screen Not Responding Correctly: Perform a touch calibration as described in section 3.22.
  • Steering Wheel Controls Not Saving: If buttons cannot be saved during learning (20K mode) or after learning, try switching the pull-up resistance value and re-learn. This function is for models without CAN-BUS.

6. User Tips

  • For optimal performance, ensure all wiring connections are secure and correctly made before powering on the unit.
  • Many users appreciate the seamless integration of wireless CarPlay and Android Auto for navigation and music.
  • If experiencing issues with steering wheel controls, try the 20K mode for learning.
  • Remember to log in to ESSGOO+ with your Google or Facebook account to access product introductions and operation videos.
  • Keep the instruction manual (PDF) handy for detailed wiring diagrams and troubleshooting steps.

7. Warranty and Support

7.1. Warranty Information

This product comes with a 1-year warranty. For products with quality issues within 1 year, they can be returned and repaired.

7.2. Customer Support

If you have any further questions or require assistance, please contact our customer service team. The user interface or functions of the product may be changed or updated without notice. It is normal if there are some differences in the manual.

  • Official Website: www.essgoo.com
  • Facebook ID: Essgoo.Official
  • Email Support: support@essgoo.com
  • Phone (United States): +1 2065363281
  • Phone (Germany): +49 8001014317
  • Phone (United Kingdom): +44 1518080196

7.3. Privacy and Compliance

To learn how your personal information is protected, please visit our privacy policy: https://essgoo.com/pages/privacy-policy

This device complies with the essential requirements and other relevant provisions of Directive 2014/30/EU or Directive 2014/53/EU.

A copy of the EU Declaration of Conformity is available online at: https://essgoo.com/pages/doc

You can also scan the QR code below to access the URL and view the Doc file:

QR code to access EU Declaration of Conformity document.
Scan for EU Declaration of Conformity

7.4. User Manual (PDF)

A detailed user manual in PDF format is available for download. This document provides comprehensive instructions and diagrams for installation, operation, and troubleshooting.

You can access the PDF manual here: View User Manual (PDF)


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.