SUNSUN JDP-18000

Contents

SUNSUN JDP Series DC Water Pump User Manual

Intelligent Frequency Conversion Submersible Water Pump for Aquariums and Ponds

1. Introduction

Thank you for choosing the SUNSUN JDP Series DC Water Pump. This intelligent frequency conversion pump is designed for efficient and quiet operation in various aquatic environments, including marine reef aquariums, freshwater aquariums, and ponds. Its DC-24V low voltage design ensures safety, while the intelligent controller allows for precise flow and power adjustments. This manual provides essential information for the safe installation, operation, and maintenance of your JDP water pump.

SUNSUN JDP-18000 water pump with intelligent controller and various outlet sizes
Figure 1: SUNSUN JDP-18000 Water Pump with Intelligent Controller and Outlet Adapters (30mm, 40mm, 50mm)

2. Safety Information

  • Always disconnect the power supply before performing any maintenance or installation.
  • The pump operates on DC-24V low voltage for enhanced safety. Ensure the power adapter is correctly connected and rated for 100-240V input.
  • Do not operate the pump dry. Ensure it is fully submerged in water during operation (for submersible use).
  • Keep the power adapter and controller away from water to prevent electrical hazards.
  • Regularly inspect the power cord and connections for any damage. Do not use if damaged.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Image indicating 24V low voltage safety protection
Figure 2: The JDP series features 24V low voltage safety protection.

3. Package Contents

Please check the package to ensure all components are present and undamaged:

  • SUNSUN JDP Series Water Pump
  • Intelligent Controller (DC-24V)
  • Power Adapter (100-240V input)
  • Various Outlet Adapters (e.g., 30mm, 40mm, 50mm for JDP-18000; 20mm, 25mm, 30mm, 32mm for JDP-6000; 25mm, 30mm, 32mm, 40mm, 45mm for JDP-10000)
  • Wire Connectors
Components of JDP-6000/JDP-10000 and JDP-3500 water pumps, including pump, outlet, controller, and adapter with wire lengths.
Figure 3: Typical package contents for JDP-6000/JDP-10000 and JDP-3500 models. Note wire lengths: 2.4M for pump to controller, 1.4M for adapter to controller.

4. Specifications

The JDP series offers various models with different performance characteristics:

Table of specifications for SUNSUN JDP-3500, JDP-6000, and JDP-10000 models, including power supply, gear positions, power, water flow, head, and dimensions.
Figure 4: Detailed Specifications for JDP-3500, JDP-6000, and JDP-10000 models.

For the JDP-18000 model:

  • Dimensions: 230 x 120 x 150 mm
  • Power: 40 - 160 W
  • Lift: 2.8 - 6.8 m
  • Flow: 10000 - 18000 L/h
  • Power Supply: DC-24V (via 100-240V AC adapter)
JDP-18000 pump with specifications overlay: 24v frequency conversion, 230x120x150mm, power 40-160w, lift 2.8-6.8m, flow 10000-18000l/h.
Figure 5: Specifications for the JDP-18000 model.

General Features:

  • Pure copper motor with three-phase brushless and non-inductive drive control technology for long-lasting, stable, and safe operation.
  • Efficient mute design ensures quiet operation even at high speeds.
  • Removable mesh cover effectively filters foreign matter and prevents small fish from being inhaled.
  • Damping foot pads reduce vibration and noise.

5. Setup and Installation

5.1. Component Connection

  1. Connect the water pump to the intelligent controller using the provided cable. Ensure the connection is secure.
  2. Connect the power adapter to the intelligent controller.
  3. Plug the power adapter into a suitable 100-240V AC power outlet.
Installation diagram showing connections between the controller, water pump outlet, cable, and power adapter.
Figure 6: Installation Diagram. Connect the pump to the controller, and the controller to the adapter.
Close-up of a wire connector and a high-quality power plug.
Figure 7: Secure wire connector and high-quality power plug.

5.2. Outlet Installation

Select the appropriate outlet adapter (e.g., 30mm, 40mm, 50mm) for your tubing and securely attach it to the pump's outlet.

JDP-10000 pump with various outlet adapters (45mm, 25mm, 30mm, 32mm, 40mm) for different hose sizes.
Figure 8: Example of various outlet adapters for JDP-10000 model.

5.3. Amphibious Use

The JDP pump can be used both submerged and externally (amphibious). For amphibious use, remove the water filter cover and install the appropriate joint directly to the pump's inlet.

Diagram showing how to configure the JDP-6000 pump for amphibious use by removing the filter cover and installing a joint.
Figure 9: Configuring the pump for amphibious use.

6. Operating Instructions

The intelligent controller provides easy adjustment of pump power and features a feeding mode.

Close-up of the SUNSUN intelligent controller (JDP-6000 model) showing power button, plus/minus buttons, 5-speed adjustment, and 15min/60min feeding mode buttons.
Figure 10: Intelligent Controller Interface.
  1. Power On/Off: After connecting the power, press the power button (Power button icon) to turn the water pump on or off. If the pump is not used for a long time, it is recommended to turn off the power.
  2. Adjust Pump Power: Tap the "+" or "-" buttons to adjust the pump's power. The controller typically offers 5 speed/power adjustments.
  3. Feeding Function:
    • Press the "||" button once for a 15-minute feeding pause. The 15min indicator light will illuminate.
    • Press the "||" button again to enter a 60-minute feeding pause. The 60min indicator light will illuminate.
    • During the feeding function, the pump stops running. After 15 or 60 minutes, the pump will automatically resume operation.
    • You can also press the "||" button again to manually resume pump operation before the timer expires.
Controller adjustment instructions showing 2 gear positions and 5-speed power adjustment, with steps for power on/off, power adjustment, and feeding function.
Figure 11: Detailed Controller Adjustment Instructions.

7. Maintenance

  • Regular Cleaning: Periodically clean the pump, especially the impeller and the mesh cover, to prevent blockages and maintain optimal performance.
  • Mesh Cover: The removable mesh cover should be cleaned regularly to ensure effective filtration and prevent debris buildup.
  • Impeller Inspection: Check the impeller for any signs of wear or damage. A damaged impeller can lead to reduced performance or increased noise.
  • Damping Foot Pads: Ensure the damping foot pads are intact and properly positioned to continue reducing vibration and noise.
  • Always disconnect power before cleaning or performing any maintenance.
Images showing the removable mesh cover for filtering impurities and damping foot pads for reducing vibration and noise.
Figure 12: Removable mesh cover and damping foot pads for easy maintenance and quiet operation.

8. Troubleshooting

ProblemPossible CauseSolution
Pump does not startNo power supply; Loose connections; Damaged adapter/controller.Check power outlet; Ensure all cables are securely connected; Inspect adapter and controller for damage.
Reduced water flowClogged mesh cover or impeller; Blockage in tubing; Pump operating at low power setting.Clean mesh cover and impeller; Check tubing for obstructions; Increase pump power using the controller.
Excessive noise/vibrationDebris in impeller; Worn impeller; Improper seating of pump; Damaged damping foot pads.Clean impeller; Replace impeller if worn; Ensure pump is securely placed; Check damping foot pads.
Pump stops intermittentlyFeeding mode activated; Overheating protection.Check controller for active feeding mode; Ensure adequate water circulation for cooling.

9. User Tips

No specific user tips were available from provided reviews or Q&A. However, general best practices include:

  • Always test the pump in a separate container of water before placing it in your main aquarium or pond.
  • Consider the head height and flow rate requirements of your setup when choosing the pump model and power setting.
  • For optimal performance and longevity, ensure the pump is not exposed to extreme temperatures or direct sunlight.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.