SEBO WP-200M, WP-50M, WP-100M, WP-300M, WP-400M, WP-800M, WP-8000, WP-5000, WP 880, WP 4880, LED-5800FP, WP-500D, WP 1880, WP 2880, WP 3880, LED-3800FP, LED-9800FP, LED-7800FP, WP-200D, WP-300D, W

Contents

SEBO Wave Making Submersible Pump Instruction Manual

Models: WP-200M, WP-50M, WP-100M, WP-300M, WP-400M, WP-800M, WP-8000, WP-5000, WP 880, WP 4880, LED-5800FP, WP-500D, WP 1880, WP 2880, WP 3880, LED-3800FP, LED-9800FP, LED-7800FP, WP-200D, WP-300D, WP-9200, WP-9600, WP-9900, WP-10800

1. Introduction

Thank you for choosing a SEBO Wave Making Submersible Pump. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your pump. Please read this manual thoroughly before use and retain it for future reference.

SEBO Wave Making Submersible Pump with water jet
Figure 1: A typical SEBO Wave Making Submersible Pump in operation, creating a water jet.

2. Safety Instructions

  • Always disconnect the power supply before handling, installing, or performing maintenance on the pump.
  • Ensure the pump is fully submerged in water during operation to prevent overheating.
  • Do not operate the pump if the power cord or plug is damaged.
  • This pump is designed for water circulation and wave making in aquariums or ponds. Do not use it for other liquids or purposes.
  • Keep out of reach of children.

3. Setup

3.1 Unpacking

Carefully remove the pump and all accessories from the packaging. Inspect for any damage during transit. If any damage is found, do not proceed with installation and contact support.

Multiple SEBO pump product boxes
Figure 2: Various SEBO pump models in their retail packaging.

3.2 Placement

  • Position the pump in the desired location within your aquarium or pond. Ensure it is placed on a stable, flat surface.
  • For wave-making models, consider the direction of water flow to achieve the desired effect.
  • Ensure the water level is sufficient to completely submerge the pump.

3.3 Connecting Accessories

Attach any necessary accessories such as fountain nozzles or outflow pipes. Some models come with various attachments for different water effects.

Two submersible pumps with fountain attachments
Figure 3: SEBO pumps equipped with fountain attachments for decorative water features.

4. Operating Instructions

  1. Ensure the pump is correctly installed and fully submerged in water.
  2. Verify that all connections are secure.
  3. Plug the pump into a suitable power outlet. The pump should start operating immediately.
  4. Observe the water flow and adjust the pump's position or outflow direction if necessary to achieve the desired effect.
  5. For models with LED lighting (e.g., LED-5800FP), ensure the lighting element is also submerged and functioning.
Blue submersible pump creating water splash
Figure 4: A blue SEBO submersible pump actively circulating water.

5. Maintenance

5.1 Regular Cleaning

Regular cleaning is crucial for maintaining the pump's efficiency and lifespan. Perform cleaning at least once a month, or more frequently if the water is particularly dirty.

  1. Disconnect the pump from the power supply.
  2. Remove the pump from the water.
  3. Disassemble the pump casing and remove the impeller. Refer to Figure 5 for general pump structure.
  4. Clean the impeller, impeller housing, and filter sponge (if present) with a soft brush and clean water. Remove any debris, algae, or mineral deposits.
  5. Rinse all components thoroughly.
  6. Reassemble the pump, ensuring all parts are correctly fitted.
  7. Place the pump back into the water and reconnect the power.
Two different sized submersible pumps
Figure 5: Examples of SEBO submersible pumps, illustrating their general design for maintenance access.

5.2 Winterization (for outdoor use)

If using the pump outdoors in freezing conditions, remove it from the water, clean it thoroughly, and store it in a dry, frost-free location.

6. Troubleshooting

Common Issues and Solutions
Problem Possible Cause Solution
Pump does not start No power; Impeller jammed; Airlock Check power connection; Clean impeller; Briefly lift and re-submerge pump to release air.
Low water flow Clogged intake/impeller; Low water level Clean intake and impeller; Ensure pump is fully submerged.
Excessive noise/vibration Impeller damaged or dirty; Pump not stable Clean or replace impeller; Ensure pump is on a stable surface.
LED lights not working LED unit faulty; Power issue Check connections; Contact support if unit is faulty.

7. Specifications

General Specifications
Feature Detail
Product Type Wave Making Submersible Pump
Material Stainless steel
Power Source Electric
Origin Mainland China
High-concerned chemical None
Customized Support OEM

Model Specifics

  • WP-200M: 12W
  • Other models include: WP-50M, WP-100M, WP-300M, WP-400M, WP-800M, WP-8000, WP-5000, WP 880, WP 4880, LED-5800FP, WP-500D, WP 1880, WP 2880, WP 3880, LED-3800FP, LED-9800FP, LED-7800FP, WP-200D, WP-300D, WP-9200, WP-9600, WP-9900, WP-10800. (Specific power/flow rates for these models are not provided in the available data. Please refer to product packaging or seller for detailed specifications.)
Four silver/grey submersible pumps of different models
Figure 6: A selection of SEBO submersible pumps, showcasing various models and sizes.

8. User Tips

  • For optimal wave-making effects, experiment with pump placement and angle within your tank.
  • Consider using a timer for your pump to simulate natural day/night cycles or specific water movement patterns.
  • Always ensure the pump's intake is clear of large debris to prevent blockages and maintain consistent flow.
  • If using in a planted aquarium, ensure plants do not obstruct the pump's operation or intake.

9. Warranty and Support

Specific warranty details are not provided in the available product information. For any warranty claims or technical support, please contact the seller directly.

For professional service and support, you may contact the seller via WhatsApp at: +86 151 1145 8002.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.