JIKONG PB2A16S15P

Contents

JIKONG PB2A16S15P BMS User Manual

Model: PB2A16S15P | Brand: JIKONG

1. Introduction

The JIKONG PB2A16S15P is an intelligent Battery Management System (BMS) designed for large-capacity series lithium battery packs. It is compatible with LiFePo4, Li-Ion, and LTO battery types, supporting configurations from 8S to 16S (24V to 48V systems) with a continuous charge/discharge current of 150A. This BMS offers comprehensive protection and management features, including voltage acquisition, high-current active balancing, overcharge, over-discharge, overcurrent, over-temperature protection, coulomb counting, Bluetooth communication, and host computer monitoring.

Its robust design and advanced features make it suitable for various applications, including home energy storage systems, communication base stations, building energy storage, and industrial equipment backup power.

JIKONG PB2A16S15P BMS board with optional 7.0 inch LCD display
Figure 1: JIKONG PB2A16S15P BMS with optional 7.0 inch LCD display.
Diagram showing various application scenarios for the JIKONG Home Energy Storage BMS, including home, communication base station, building energy storage, industrial energy storage, and office.
Figure 2: Application scenarios for the JIKONG Home Energy Storage BMS.

2. Safety Guidelines

Please read and understand all instructions before installation and operation. Failure to follow safety guidelines may result in property damage, serious injury, or death.

  • Always wear appropriate personal protective equipment (PPE) when handling batteries and electrical components.
  • Ensure all power sources are disconnected before performing any wiring or maintenance.
  • Verify correct polarity and connections before applying power to the BMS. Incorrect wiring can cause damage to the BMS and battery pack.
  • Do not attempt to repair or modify the BMS. Refer to qualified personnel for service.
  • Keep the BMS away from water, moisture, and flammable materials.
  • Ensure adequate ventilation around the battery system to prevent overheating.

3. Package Contents

Upon receiving your JIKONG PB2A16S15P BMS, please verify that all items listed below are included in the package:

Packing list showing a brown packing box, the BMS board, an interface board, an adapter, RJ45 network cable, heating adapter cables, sampling lines, and adapter cables.
Figure 3: JIKONG PB2A16S15P BMS Packing List.
  1. Packing Box
  2. BMS Unit
  3. Interface Board
  4. Adapter
  5. RJ45 Network Cable (400mm)
  6. Cells Total B+ Cable x1 (500mm)
  7. Heating Adapter Cable x1 (170mm)
  8. Sampling Line A (900mm)
  9. Sampling Line B (900mm)
  10. Sampling Line C (900mm)
  11. Adapter Cable A (300mm)
  12. Adapter Cable B (300mm)
  13. Adapter Cable C (300mm)
  14. 4.3LCD-TTL-P (Optional, if ordered with LCD)

4. Installation

4.1. Physical Installation and Dimensions

The BMS unit should be securely mounted in a location that provides adequate ventilation and protection from environmental elements. The dimensions of the JK-PB1/2A16S-10/15/20P series protection board are 300mm x 100mm x 24mm.

Exploded view diagram of the BMS showing cooling aluminum alloy, flexible wiring terminals, high performance MCU, parallel current limiting module, and low internal resistance MOS components.
Figure 4: Internal components and cooling design of the BMS.
Close-up of the BMS board showing cooling aluminum alloy heat sinks and various connection points.
Figure 5: Aluminum alloy heat sink detail for temperature reduction.

4.2. Wiring Diagrams

The wiring method varies depending on the number of battery cells (strings) in your battery pack. Ensure all balance cables are properly connected and that the main positive (B+) and negative (B-) terminals are correctly wired.

4.2.1. 16-String Cell Wiring

Wiring diagram for a 16-string cell battery pack connected to the JIKONG BMS, showing individual cell connections, temperature control switch, and charger/load connections.
Figure 6: Wiring method for 16-string cells.

4.2.2. 8-String Cell Wiring

Wiring diagram for an 8-string cell battery pack connected to the JIKONG BMS, showing individual cell connections, temperature control switch, and charger/load connections.
Figure 7: Wiring method for 8-string cells.

4.3. Interface Board Connections

The interface board provides connections for LED indicators, reset switch, DIP switch, dry contacts, and communication ports (CAN, RS485). Refer to the diagram and pin definitions for correct connections.

Diagram of the BMS interface board showing RS485-2, RS485-1, CAN, Dial Switch, RS232, Dry Interface, Switch, Sampling line ports, UART Port, Display or Switch Port, and Heat Function Port.
Figure 8: BMS Interface Board Layout and Ports.
Table 1: Key Interface Pin Definitions
ConnectorPin NameDescription
P4 (URAT Display)K- / K+Activation Signal Negative / Positive Electrode
P4 (URAT Display)GNDPower Negative Terminal
P4 (URAT Display)RX / TXUART Communication
P4 (URAT Display)VCCDisplay Power Output
P5 (Display)A / BDisplay RS485 Signal Negative / Positive
P6 (Acquisition)NT1NTC1 Temperature Probe Connection
P6 (Acquisition)B0-B4Battery Cell Positive Connections (B0: Total Negative, B1: 1st Cell Positive, etc.)
P10 (Heating)HT-Heater Element Negative Electrode
P11 (Power Input)B+Power Input Positive
B-B-Connect to the negative battery terminal (M6 screw)
P-P-Connect to external load or negative terminal of charger (M6 screw)

4.4. Device Activation

Before powering on the protection board, double-check all balance cable connections and ensure that P- and B- are correctly connected. Confirm the protection board is securely fixed to the battery cells. Once verified, power on the BMS.

The BMS is designed for charging activation. This means that after the battery assembly is complete, you need to connect a charger (with a voltage 2V higher than the battery voltage) to activate the protection board. Alternatively, if you have an optional display screen or button, you can activate the device by inserting the cable into the display interface and pressing the button.

5. Operation

5.1. APP Installation and Connection

The JIKONG BMS supports mobile APP control for Android (version 7 minimum) and iOS operating systems. You can download the APP by scanning the QR code provided in the official manual. The APP connects to the BMS via Bluetooth, allowing you to monitor battery status, modify parameters, and control charge/discharge switches.

QR code for JIKONG Mobile APP link
Figure 9: Scan to download the JIKONG Mobile APP.
Screenshot showing mobile APP, PC software, and home storage display options for multi-screen data connection.
Figure 10: Multi-screen display data connection options.

5.2. Parameter Setting

Parameters can be set via the mobile APP or host computer software. This includes battery type, number of cells, battery capacity, equalization trigger differential pressure, voltage calibration, and current calibration. Default parameters are provided for Li-Ion, LiFePo4, and LTO batteries.

Screenshot of the JIKONG PC software interface showing real-time monitoring, settings, control, logging, and detailed battery parameters including cell voltages.
Figure 11: PC software interface for intelligent interaction and parameter adjustment.

5.3. Active Balancing

The BMS employs active equalization technology to transfer energy from higher-voltage cells to lower-voltage cells, ensuring battery consistency and prolonging battery life. The default balancing current is 1A/2A, adjustable based on battery capacity (recommended not to exceed 0.2C).

Diagram illustrating active balancing (lossless balancing) in a battery pack, showing energy transfer from higher to lower energy cells.
Figure 12: Active Balancing (Lossless Balancing) principle.
Comparison showing efficient balance prolonging battery life, with ordinary home storage protection boards having 30-100mA balanced current versus home storage BMS with 1A-2A balanced current.
Figure 13: Efficient balancing prolongs battery life.

5.4. Communication Protocols

The BMS supports CAN and RS485 communication. The default CAN communication rate is 250K. Users can select the appropriate protocol in the APP based on their inverter brand (e.g., Deye, Pylontech, Growatt, Victron, Invt, Goodwe, SMA, Voltronic Power, SRNE, MUST).

Mobile APP screenshot showing various inverter communication protocols available for selection, including Deye, Pylontech, Growatt, Victron, Invt, Goodwe, SMA, Voltronic Power, SRNE, and MUST.
Figure 14: Mobile APP for protocol docking.
PC software interface for setting CAN protocols, listing JIKONG, NIU, China tower, Growatt, Voltronic, and WOW.
Figure 15: PC software for inverter communication protocol settings.

5.5. Parallel Function

The parallel function allows simultaneous monitoring of multiple BMS units by a host computer via the RS485 bus. This requires a USB to RS485 serial port cable and the JIKONG host computer software. Up to 16 BMS units can be connected in parallel, each requiring a unique address (0-15) set via DIP switches. BMS with address 0 acts as the host, and 1-15 as slaves.

Diagram illustrating the parallel monitoring setup for JIKONG energy storage series protection boards, showing multiple BMS units connected via RS485 to a host computer.
Figure 16: Parallel monitoring setup for multiple BMS units.

5.6. Heating Function

The BMS includes a heating function to prevent battery activity reduction in low-temperature environments. It uses a resistance heater or heating film (not included) with a designed heating current of 10A. This function can be enabled or disabled via the APP. It is recommended to use a normally closed temperature switch (45°C to 65°C) in series with the heating circuit as a secondary protection.

5.7. Dry Contact Function

Two dry contacts are provided to control external devices like alarms or fans. When the BMS detects an over-temperature, overcharge, or over-discharge state, the dry contacts can switch status to trigger an alarm or activate a cooling fan. You can select two trigger conditions based on your specific needs.

Wiring diagram for dry contact function, showing connection to an external buzzer and DC power supply.
Figure 17: Dry contact wiring diagram for external alarm equipment.

6. Protection Features

The JIKONG PB2A16S15P BMS offers comprehensive protection to ensure the safety and longevity of your battery pack:

  • Overcharge Protection: Prevents cells from being overcharged by shutting off charging when any cell voltage exceeds the set overcharge protection voltage. Charging resumes when all cell voltages drop below the recovery voltage.
  • Over-discharge Protection: Prevents cells from being over-discharged by shutting off discharge when any cell voltage drops below the set undervoltage protection voltage. Discharge resumes when cells are charged above the recovery voltage. An automatic shutdown voltage is also present for critical low voltage.
  • Charge Overcurrent Protection: Protects against excessive charging current. If the charging current exceeds the set continuous charging current for a specified delay, charging is stopped.
  • Discharge Overcurrent Protection: Protects against excessive discharging current. If the discharging current exceeds the set continuous discharging current for a specified delay, discharging is stopped.
  • Over-temperature Protection: Monitors battery temperature and stops charging/discharging if temperatures exceed set limits. Operations resume when temperatures return to safe levels.
  • Low Temperature Protection: Stops charging if battery temperature drops below a set low-temperature limit to prevent damage. Charging resumes when the temperature recovers.
  • Short Circuit Protection: Automatically protects against short circuits. Users can adjust the short circuit protection delay and recovery time via the APP.
  • Charge Current Limiting: If the charging current exceeds a set limit, the BMS will limit the charging current to approximately 10A to protect the battery.
  • Intelligent Sleep Function: The BMS can enter an intelligent sleep mode (after 26 consecutive hours with charge/discharge current less than 1A) to reduce its own power consumption. It can be reactivated by pressing a button or connecting a charger.
  • Emergency Switch: In case of critical issues like over-temperature, over-discharge, overcharge, or string drop, activating the emergency switch via the APP will enable charge and discharge for 30 minutes, allowing for emergency use.

7. Specifications

Below are the key technical parameters for the JIKONG PB2A16S15P BMS:

Product specifications table for JIKONG PB2A16S15P BMS, listing Balance Method, BMS Type, Function, Battery Type, Balance Current, Charge/Discharge, Battery Strings, and Size.
Figure 18: Summary of JIKONG PB2A16S15P BMS Specifications.
Table 2: Detailed Product Parameters (JK-PB2A16S-15P Model)
ParameterValueUnit
Supply Voltage20-70V
Standby Power Consumption12mW
Operating Power Consumption1100mW
Operating Temperature-30 to 70°C
Max Number of Collection Strings16S
Max Balancing Current2A
Max Charging Current150A
Max Discharge Current150A
Max Instantaneous Current300A
Internal Loop Resistance0.45mΩ
Protective Plate Size300*100*24mm
Finished Weight1000g

7.1. Optional LCD Display Dimensions

If you have purchased the BMS with an optional LCD display, refer to the dimensions below:

Dimensions of the 7.0 inch LCD display: 187mm width, 120mm height, 154mm screen width, 86mm screen height, with a 500mm total length cable.
Figure 19: Dimensions for 7.0 inch LCD display.
Dimensions of the 4.3 inch LCD display: 136.5mm width, 95.4mm height, 96.5mm screen width, 55.4mm screen height, with a 500mm total length cable.
Figure 20: Dimensions for 4.3 inch LCD display.

8. Troubleshooting

This section provides general guidance for common issues. For detailed diagnostics, refer to the APP or PC software interface, which provides real-time data and warning lists.

  • BMS Not Powering On: Ensure the device is activated correctly (see Section 4.4). Check all main power connections (B+, B-, P-).
  • Battery Imbalance: Verify that active balancing is enabled in the APP. Check individual cell voltages via the APP to identify problematic cells.
  • Protection Triggered (e.g., Overvoltage, Overcurrent): The BMS will automatically stop charging or discharging. Check the battery parameters and load/charger specifications. Review the warning list in the APP for specific fault codes.
  • Communication Issues (Bluetooth, CAN, RS485): For Bluetooth, ensure the APP is installed correctly and the device is within range. For CAN/RS485, check wiring, baud rates, and protocol settings in the APP/PC software. For parallel setups, verify DIP switch addresses.
  • Heating Function Not Working: Ensure the heating function is enabled in the APP. Check the external heating element and its connections. Verify the temperature control switch is functioning correctly.
  • Unexpected Shutdown: Check for any triggered protection events (e.g., over-discharge, over-temperature). Review the event logs in the PC software or APP.

9. User Tips

  • Regular Monitoring: Periodically check battery parameters via the mobile APP or PC software to ensure optimal performance and detect potential issues early.
  • Parameter Customization: Take advantage of the adjustable protection parameters to fine-tune the BMS to your specific battery chemistry and application requirements. Always understand the implications of changes before applying them.
  • Firmware Updates: Check the manufacturer's website or APP for any available firmware updates to ensure your BMS has the latest features and bug fixes.
  • Cable Management: Ensure all wiring, especially balance leads, are neatly routed and secured to prevent accidental disconnections or damage.

10. Support and Warranty

For technical support, troubleshooting assistance, or warranty inquiries, please contact JIKONG customer service through their official channels. Keep your purchase receipt and product serial number handy when contacting support.

This product is covered by a manufacturer's warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region and retailer. Please refer to your purchase documentation for detailed warranty information.

11. Additional Resources

A detailed user manual in PDF format is available for download. This document provides in-depth information on all aspects of the JIKONG PB2A16S15P BMS, including comprehensive wiring diagrams, detailed parameter explanations, and advanced configuration options.

You can access the PDF manual here: JIKONG PB2A16S15P User Manual (PDF)

© 2024 JIKONG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.