Introduction
The CONTEC SP750VET Automatic Veterinary Infusion Pump is a high-capacity, high-safety device designed for precise and controlled fluid delivery to pets. This manual provides essential information for the safe and effective setup, operation, and maintenance of the device, ensuring optimal treatment effects and patient safety.
Package Contents
Before proceeding with setup, please verify that all items are present in the package:
- CONTEC SP750VET Infusion Pump Unit
- User Manual
- Power Cord
- Mounting Bracket and Screws
Setup
- **Unpacking:** Carefully remove the infusion pump and all accessories from the packaging. Inspect for any visible damage.
- **Power Connection:** Connect the provided power cord to the power input port on the back of the pump and then to a suitable power outlet.
- **Mounting (Optional):** If wall-mounting or pole-mounting is required, attach the mounting bracket to the desired surface or pole using the provided screws. Secure the infusion pump to the bracket. The pump features a self-contained installation method.
- **Infusion Set Installation:** Open the pump door by pressing the 'PUSH' button and sliding the 'LOCK' mechanism. Carefully insert the infusion line into the designated slot, ensuring it is properly seated and secured. Close the pump door.
Operating Instructions
The CONTEC SP750VET features a user-friendly interface for setting infusion parameters. Refer to the video demonstration for a visual guide.
- **Power On:** Press the 'ON/OFF' button to power on the device. The display will illuminate.
- **Setting Infusion Rate:** Use the arrow keys (up/down) to navigate to the 'Rate' setting on the display. Use the left/right arrow keys to select the digit to change, and the up/down keys to adjust the value. Confirm with 'OK' or the appropriate button.
- **Setting Total Volume:** Navigate to the 'Total' setting. Adjust the desired total infusion volume using the arrow keys. Confirm your selection.
- **Selecting Infusion Type:** If applicable, navigate to 'Type' to select the appropriate infusion set type (e.g., ANDE, Weigao). This ensures accurate flow control.
- **Clearing Volume:** To clear the 'Already' infused volume, navigate to 'Clear' and confirm.
- **System Settings:** Access 'Sys Setting' for advanced configurations, which may require a password (e.g., '1239' as shown in the video).
- **Start/Stop Infusion:** Press the 'START/STOP' button to begin or pause the infusion.
- **Bolus Function:** Use the 'BOLUS' button for rapid fluid delivery if required.
Video 1: Demonstration of CONTEC SP750VET Infusion Pump operation, including setting parameters and alarm indication.
Maintenance
Proper maintenance ensures the longevity and accuracy of your infusion pump.
- **Cleaning:** Regularly clean the exterior of the pump with a soft, damp cloth. Do not use abrasive cleaners or immerse the device in liquid.
- **Disinfection:** Follow standard veterinary protocols for disinfecting surfaces that come into contact with patients or fluids.
- **Battery Care:** If the device has an internal battery, ensure it is charged regularly to maintain optimal performance.
- **Storage:** Store the pump in a clean, dry environment away from direct sunlight and extreme temperatures.
- **Calibration:** Periodic calibration by qualified personnel is recommended to maintain accuracy.
Troubleshooting
This section addresses common issues you might encounter with the infusion pump.
| Problem | Possible Cause | Solution |
|---|---|---|
| "Air bubble in IV tube!" alarm | Air detected in the infusion line. | Check the infusion line for air bubbles. Prime the line if necessary to remove air. Ensure proper installation of the infusion set. |
| Pump not powering on | Power cord disconnected, power outlet issue, or internal battery depleted. | Ensure the power cord is securely connected and the outlet is functional. Charge the internal battery if applicable. |
| Incorrect infusion rate | Incorrect rate setting, wrong infusion set type selected, or kinked tubing. | Verify the set infusion rate. Confirm the correct infusion set type is selected in the system settings. Check the tubing for obstructions. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | SP750VET |
| Installation Method | Self-contained |
| Material | Metal |
| Package Weight | 4.0 kg |
| Package Dimensions (L x W x H) | 23 cm x 22 cm x 20 cm |
User Tips
While no specific user reviews or Q&A were provided for this product, general tips for using veterinary infusion pumps include:
- Always ensure the infusion line is free of air bubbles before starting infusion to prevent air embolism.
- Double-check all settings (rate, total volume, infusion set type) before initiating treatment.
- Monitor the patient and the pump regularly during infusion for any alarms or changes in condition.
- Keep the pump clean and disinfected between uses to prevent cross-contamination.
Warranty and Support
For warranty information, technical support, or service inquiries, please contact your local distributor or the manufacturer directly. Keep your purchase records handy when contacting support.
Manufacturer: CONTEC Medical Systems Co., Ltd.