1. Introduction
The Sub250 OasisFly35 DC is a high-performance 3.5-inch FPV CineWhoop drone designed for versatile flight scenarios and exceptional footage. It features a DC frame for clear visuals, powerful 1804 motors, an efficient 45A AIO ESC, and integrated GPS for reliable flight. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your OasisFly35 DC drone.
Figure 1: Sub250 OasisFly35 DC FPV Drone
Key Features:
- Compatible with Analog / O3 / O4 Pro VTX options for flexible setups.
- DC frame design for unobstructed, pure visuals and heightened flight immersion.
- 1804 3450KV motors paired with efficient 45A AIO ESC for strong, responsive power.
- Integrated side-plate structure for enhanced aerodynamics, durability, and protection of internal electronics.
- GPS standard across all models for confident flying and Return-to-Home (RTH) functionality.
Note: Contents vary by selected WTFPV or Analog specifications. The WTFPV version does not come with any VTX, camera, or antenna.
2. Setup and Assembly
Your OasisFly35 DC drone comes in a Ready-to-Go state of assembly. However, depending on your chosen version (WTFPV, Analog, O4 Pro), some components like VTX, camera, and antenna may need to be installed. Please refer to the following lists for included components.
2.1 Product List (Main Components)
Figure 2: Overview of included drone and main accessories.
| Item | Quantity |
|---|---|
| OasisFly35 DC Drone | 1 |
| HQ T3.5*3.5*3 (2CW+2CCW) Propellers | 1 set |
| Left Side Plate | 1 |
| Right Side Plate | 1 |
| Right Rear Side Plate | 1 |
| Left Rear Side Plate | 1 |
| O3 Version Silicon Pad | 1 |
| Battery Anti-Slip Pad | 1 |
| Printed Analog Camera Mount (Pair) | 1 |
| Textured Aluminum Standoffs | 2 |
| USB-C Adapter Board | 1 |
| Dual-Head SH1.0-5P Female-to-Male Terminal Cable | 1 |
| M2 Hex Mini Wrench | 1 |
| EVA Vibration-Damping Landing Pads | 8 |
| 11x170 mm Battery Strap | 1 |
| TPU Vibration-Damping Landing Pads | 1 |
2.2 Spare Screws Included
Figure 3: List of spare screws for maintenance and assembly.
| Item | Quantity |
|---|---|
| M2×16 Socket Head Hex Screws | 2 |
| M2×12 Round-head Hex Screws | 2 |
| M2×8 Round-head Hex Screws | 8 |
| M2×7 Socket Head Hex Screws | 8 |
| M2×5 Round-head Hex Screws | 4 |
| M2×4.5 Round-head Hex Screws | 1 |
| M2 Hex Nuts | 2 |
3. Operating Instructions
3.1 Power and Control
- The drone uses an XT30 power connector. Ensure your 4S 530mAh battery (recommended) is fully charged before flight.
- The drone supports ELRS/PNP receivers. Ensure your remote controller is properly bound and configured to the drone's receiver.
- The drone is equipped with 1804 3450KV motors and a RedFox A3 45A AIO ESC, providing responsive power for various maneuvers.
3.2 Flight Features
- Crystal-clear View: The DC frame design, especially when paired with O4 Pro HD VTX (if applicable to your version), delivers unobstructed and pure visuals for an immersive flight experience.
- Multi-VTX Compatibility: The OasisFly35 DC supports Analog, O3, and O4 Pro VTX options, allowing for flexible setups and adaptation to different flight scenarios.
- GPS Functionality: All models come standard with GPS (SUB-M10). In complex environments or preset conditions, activate GPS Rescue via your remote controller to ensure flight safety and reliable Return-to-Home (RTH).
Figure 4: GPS module for confident flights and rescue functions.
Figure 5: Multi-VTX compatibility for flexible setups.
Figure 6: The OasisFly35 DC is versatile for freestyle, motion follow, outdoor cinematics, and commercial filming.
4. Maintenance
Regular maintenance ensures the longevity and optimal performance of your OasisFly35 DC drone.
- Frame Integrity: The drone features an integrated side-plate structure and a 7-series aluminum lens mount, designed for durability and protection. Regularly inspect the frame, arms, and lens mount for any cracks, bends, or loose screws, especially after impacts.
- Propeller Inspection: Before each flight, check propellers for any damage (chips, cracks, bends). Damaged propellers can cause instability and reduce flight efficiency. Replace them immediately if any damage is found.
- Motor and ESC Care: The 1804 motors and 45A AIO ESC are designed for high performance. Keep them free from dust, dirt, and debris. Avoid operating in excessively sandy or dusty environments.
- Battery Care: Use only recommended 4S 530mAh batteries. Store batteries properly, avoid overcharging or over-discharging, and inspect them for swelling or damage before each use.
- General Cleaning: Keep the drone clean. Use a soft, dry cloth to wipe down surfaces. Avoid using harsh chemicals or excessive moisture.
Figure 7: Integrated side plates protect internal electronics and enhance cooling.
Figure 8: CNC-machined 7-series aluminum lens mount provides reliable protection.
5. Troubleshooting
This section provides general guidance for common issues. For complex problems, please contact technical support.
- Drone Not Powering On: Check battery connection, ensure battery is charged, and inspect XT30 connector for damage.
- Loss of Control/Signal: Verify remote controller is powered on and bound to the drone. Check for electromagnetic interference in the flight area. Ensure receiver antenna is properly positioned and undamaged.
- Unstable Flight: Inspect propellers for damage or imbalance. Check for loose components or screws on the frame. Ensure flight controller firmware is up-to-date.
- GPS Issues: Ensure the drone has a clear view of the sky for satellite acquisition. Avoid flying near tall buildings or dense foliage that can obstruct GPS signals.
- Video Feed Problems (Analog/WTFPV versions): Check VTX and camera connections. Ensure VTX is powered and operating on the correct frequency. Verify antenna connection and condition.
6. Specifications
Detailed specifications for the Sub250 OasisFly35 DC drone, available in various configurations.
Figure 9: Comparative specifications for different OasisFly35 DC versions.
| Feature | OasisFly35 DC O4 Pro | OasisFly35 DC Analog | OasisFly35 DC WTFPV |
|---|---|---|---|
| Model | OasisFly35 DC | ||
| Frame | Sub250 OasisFly35 DC | ||
| Main Plate Thickness | 2.5mm | ||
| Wheelbase | 175mm | ||
| Flight System | Sub250 RedFox A3 45A AIO | ||
| MCU | STM32F722 | ||
| Gyro | ICU 42688-P | ||
| Flash | 16MB | ||
| FC Firmware | 4.5.2 | ||
| ESC | 45A | ||
| Propeller | HQ 3.5*3.5*3 | ||
| Power Connector | XT30 | ||
| Receiver | DJI O4 Air Unit Pro built-in RX | ELRS 2.4G / PNP | |
| Motor | SUB250 1804_3450kv | ||
| Rec. Batt. | 4S 530mAh | ||
| Flight Time | 5-6min | 7min | / |
| VTX Antenna | DJI O4 Air Unit Pro Antenna | Momoda-MMCX90 | / |
| Camera | DJI O4 Air Unit Pro Camera Module | Caddx H1 Camera | / |
| VTX | DJI O4 Air Unit Pro VTX Module | Sub250 SendT 1600VTX | / |
| Weight | 194g±3 | 188g±3 | 162g±3 |
All flight times are tested under smooth cruising conditions. Actual duration may vary due to firmware version, pilot skill, and environmental factors. Data is for reference only.
7. User Tips and Safety Guidelines
7.1 Important User Tips
- Battery Not Included: Please note that the drone does not come with a battery for the drone itself or for the controller. You will need to purchase a 4S 530mAh battery (recommended) and controller batteries separately.
- Understand Basic Operations: Before flying, ensure you have a solid understanding of basic drone operation knowledge.
- Check Local Regulations: Always be aware of and comply with local government regulations regarding drone usage in your flying area to avoid legal issues.
- Pre-Flight Checks: Before every flight, confirm that all connections are secure, all equipment is functioning correctly, and control actions respond normally to prevent accidents.
7.2 Safety Guidelines
- Recreational Use Only: This product is intended for recreation use only. Illegal modification of drones/planes is prohibited.
- Adult Supervision: Model aircraft can pose certain dangers. Children should only operate the model under the direct supervision of adults.
- Safe Flying Environment: Always ensure the flying environment is safe and clear of people, animals, and obstacles.
- Avoid Bad Weather: Do not operate the drone in strong winds, rain, snow, sand/dust storms, or other adverse weather conditions.
- Electromagnetic Interference: Avoid flying in environments with strong electromagnetic interference (e.g., near radio transmission towers, high-voltage wires, substations, mining areas).
- Wireless Device Interference: Be mindful of interference from other wireless devices (e.g., transmitters, video-downlink, Wi-Fi signals).
- Component Condition: Do not fly if components are aged or damaged.
- Battery Condition: Never operate the unit with a low charge or defective battery.
8. Warranty and Support
8.1 Warranty Policy Exclusions
The warranty policy does NOT cover the following:
- Crashes or fire damage caused by non-manufacturing factors, including but not limited to pilot errors.
- Water damage or other damages caused by improper installation, incorrect use, or operation not in accordance with official instructions or manuals.
- Damage caused by a non-authorized service provider.
- Damage caused by unauthorized modification of circuits and error weld mismatch or misuse of the battery and charger.
- Damage caused by operation in bad weather (i.e., strong winds, rain, snow, sand/dust storms, etc.).
- Damage caused by operating the product in an environment with electromagnetic interference (i.e., in mining areas or close to radio transmission towers, high-voltage wires, substations, etc.).
- Damage caused by operating the product in an environment suffering from interference from other wireless devices (i.e., transmitter, video-downlink, Wi-Fi signals, etc.).
- Damage caused by crashes when components have aged or been damaged.
- Damage caused by operating the unit with a low charge or defective battery of any form.
- Damage resulting from any non-GEPRC technical or other support (online community for example), such as assistance with "how-to" questions and or inaccurate product set-up and installation.
- GEPRC is not responsible for issues involving 3rd party products and warranty. For example, with issues involving Caddx and DJI, the customer must get warranty support directly from the 3rd party company.
8.2 Warranty Claim Procedure
To protect your legal rights and ensure fair and efficient handling of any warranty issues, please strictly follow the procedures below.
8.2.1 Unboxing Video Requirements (Important)
To avoid disputes regarding damage during transit or missing accessories, you must record a complete, uninterrupted unboxing video immediately after receiving the package. This video will serve as the primary evidence for any after-sales claims.
Video recording rules:
- Show the original condition: Before opening, clearly film all six sides of the package. Ensure the shipping label (tracking number, recipient information) and any visible damage (crushes, punctures, water stains, or signs of resealing) are recorded.
- Continuous recording: From the moment you start unsealing until you finish checking all items, keep the camera running without pauses or edits.
- Inspect and count each item: Compare with your order. Take out every item and show them clearly in the video. This includes but is not limited to: main unit (body, serial number/SN), propellers, antenna, receiver, battery, charger, manual, accessory bag.
- Close-up of defects: If you find any cosmetic damage (scratches, dents, cracks), functional issues, or missing accessories, take a clear close-up of the problem area in the video.
Note: Without a valid unboxing video, or if the video is incomplete and does not show the original package state, our after-sales team may not be able to accept claims regarding missing items or shipping damage.
8.2.2 Packaging Requirements for Returns / Repairs
If you are instructed to send a product back for repair, please follow the packaging rules below. Any additional damage caused by improper packaging during return shipping will be your responsibility.
Packaging rules:
- Use the original box: Pack the product in the original factory box (you may place that box inside a protective outer shipping bag/carton).
- Include all accessories: All accessories, including but not limited to propellers, antenna, receiver, battery, charging cable, screw pack, must be placed inside the box together with the main unit. Missing accessories may affect the completeness of the repair.
- Secure the contents: Use the original foam, dividers, bubble wrap, etc., to ensure the main unit and accessories do not move or collide inside the box.
- Take photos before sealing: For your own records, take a photo of all items together before closing the box, and another photo of the sealed package.