DAKEFPV H743 FC 6S 55A STACK 4IN1

Contents

DAKEFPV H743 Flight Controller and 4-in-1 ESC Stack Instruction Manual

Model: H743 FC 6S 55A STACK 4IN1 | Brand: DAKEFPV

1. Introduction

This manual provides detailed instructions for the installation, setup, and operation of your DAKEFPV H743 Flight Controller (FC) and 4-in-1 Electronic Speed Controller (ESC) stack. This high-performance stack is designed for FPV (First Person View) drones, supporting popular firmware like Betaflight and Ardupilot, and is compatible with various aircraft types including X8/Y6/fixed-wing aircraft requiring more than 4 motors.

The H743 FC features an STM32H743 main control unit, dual ICM42688P gyroscopes, a built-in barometer, and 16MB of onboard flash memory for blackbox logging. The accompanying 4-in-1 ESC offers a continuous current of 70A per channel (80A peak for 10s) and supports 3-8S LiPo batteries. Please read this manual thoroughly before attempting installation or operation.

Video: Overview of the DAKEFPV H743 FC and 4-in-1 ESC Stack, showcasing its design and features.

2. Package Contents

Please verify that all items are present in your package based on the option purchased:

Package contents for Option 1: JIJIEFPV H743 70A 30x30 STACK
Image: Package contents for Option 1 - JIJIEFPV H743 70A 30x30 STACK.

Option 1 - JIJIEFPV H743 70A 30x30 STACK

  • JIJIEFPV H743 Flight Controller x 1
  • JIJIEFPV BLS 70A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • M3 Nylon Nut x 5
  • M3 Silicone O-Ring x 5
  • M3*8mm Silicone Grommets (for FC) x 1
  • M3*8.1mm Silicone Grommets (for ESC) x 1
  • SH 1.0mm 25mm-length 8-pin Cable (for FC-ESC connection) x 1
  • SH 1.0mm 75mm-length 8-pin Cable x 1
  • M3*30mm Inner-hexagon Screws x 5
  • GPS 6-pin cable, Analog VTX 6-pin cable, dual-camera 6-pin cable x 1
  • XT60 Power Cable (70mm) x 1

Note: When the ESC tail faces the drone's front, use the 75mm 8-pin cable for the flight controller and ESC; both ends plug interchangeably.

Package contents for Option 2: JIJIEFPV H743 70A 30x30 FC and Option 3: JIJIEFPV 8S 70A 4 in 1 ESC
Image: Package contents for Option 2 (FC only) and Option 3 (ESC only).

Option 2 - JIJIEFPV H743 70A 30x30 FC (Flight Controller Only)

  • JIJIEFPV H743 Flight Controller x 1
  • Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 5
  • FC 12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  • GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

Option 3 - JIJIEFPV 8S 70A 4 in 1 ESC (ESC Only)

  • JIJIEFPV 8S 70A 4 in 1 ESC
  • 35V 1000uF Low ESR Capacitor (Note: 12S ESC option sends 63V1000uF Capacitor)
  • FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  • XT60 x 1

3. Specifications

JIJIE H743 30x30 Flight Controller

FeatureSpecification
Main Control UnitSTM32H743
GyroscopeICM42688P (Dual)
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENo
WiFiNot supported
DJI Air Unit ConnectionSupports 6-pin plug-in and wiring. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1.
FLASH (Black Box)16MB
Current MeterSupported
Input Voltage3-8S LiPo
UART Ports8 groups
Buzzer PadsSupported (BZ+, BZ- pads for active 5V buzzer)
BOOT ButtonPress and hold while powering on to force DFU mode for firmware flashing.
RSSI PadSupported (located on the top right)
SmartPort/F.PortNot supported
Supported FirmwareBetaFlight (default), Ardupilot
Firmware Target NameDAKEFPPVH743
Mounting Hole30.5 x 30.5 mm (4mm diameter)
Dimensions36 x 36 x 8 mm
Weight10.5g

JIJIE 12S 70A 4-in-1 ESC

FeatureSpecification
Product NameJIJIE 12S 70A 4 in 1 ESC
FirmwareBLHeli_S / BlueJay
Battery Input3-8S LiPo
Continuous Current70A x 4
Maximum Current80A x 4 (10 seconds)
Built-in TVS DiodeYes
External Capacitor1000uF high frequency low ESR (included)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Input Voltage3-8S LiPo
Output VoltageVBAT
Current MeterSupported (Scale=400, Offset=0)
TelemetryNot supported
Mounting Hole30.5 x 30.5 mm (4mm diameter)
Dimensions45.4 x 42.8 x 6.5 mm
Weight23.5g
Dimensions of the H743 Flight Controller and ESC stack
Image: Detailed dimensions of the H743 Flight Controller and ESC stack, showing 30.5x30.5mm mounting, 36x36mm FC, 42x39mm ESC, and 15.8mm stack height.
Key features of the H743 stack
Image: Key features including 70A ESC, dual gyroscopes, 5V/12V BEC, 8 motor support, 16M flash, external GPS, 1000uF capacitor, DJI Air Unit direct plug, and built-in barometer.

4. Installation and Setup

4.1 Important Stack Installation Note

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC.

It is critical to swap the silicon pads when changing the positions of the FC and the ESC. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

Important Stack Installation Note with diagram showing space between FC and ESC
Image: Diagram illustrating the importance of leaving enough space between the FC and ESC to prevent short circuits.

4.2 Wiring Diagram

The following diagram illustrates the typical wiring connections for the H743 FC and 4-in-1 ESC stack with various peripherals. Ensure all connections are secure and correctly oriented.

Detailed wiring diagram for FC and Motors
Image: Comprehensive wiring diagram showing connections for the Flight Controller, ESC, motors, camera, VTX, receiver, GPS, and LED strip.

Note 1: In order to prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.

Note 2: The FC and ESC can also be connected via direct soldering. Soldering pads definition is as follows:

BLS 70A 4-in-1 ESC layout with motor and battery connections
Image: Layout of the BLS 70A 4-in-1 ESC, indicating motor connections (Motor 1-4), Capacitor pin holes (BAT+, GND), and TVS diode.
H743 Flight Controller layout with labeled ports
Image: Detailed layout of the H743 Flight Controller, labeling ports for GPS, ELRS, VTX, Buzzer/LED strip, USB Type-C, BOOT button, Camera inputs (CAM1, CAM2), OSD, and various power/signal pads.

4.3 Connecting Peripherals

DJI Air Unit Connection

The H743 stack supports direct plug-in for DJI Air Units. Use the provided 6-pin cable for connection.

Cable connection for DJI O3 Air Unit
Image: Diagram showing the 6-pin cable connection between the H743 FC and a DJI O3 Air Unit.
Cable connection for DJI Air Unit V1, RunCam Link, or Caddx Vista Air Unit
Image: Diagram showing the 6-pin cable connection between the H743 FC and a DJI Air Unit V1, RunCam Link, or Caddx Vista Air Unit.

SBUS Receiver Connection

When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).

If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1), you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

SBUS receiver connection warning with DJI Air Unit
Image: Diagram illustrating the SBUS receiver connection and the necessary disconnection from the DJI Air Unit harness to avoid conflicts.

ELRS Receiver Connection

We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

ELRS receiver connection warning with DJI Air Unit
Image: Diagram illustrating the ELRS receiver connection and the potential need to disconnect the SBUS wire from the DJI Air Unit harness for proper function.

LED Light Bar Connection

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to this mode, and short presses of the BOOT button let you toggle between various preset light effects.

LED light bar connection on H743 FC
Image: Diagram showing how LED light bars can be connected to the H743 Flight Controller.

5. Operation

5.1 Firmware Flashing (DFU Mode)

To enter DFU (Device Firmware Upgrade) mode for flashing new firmware (e.g., Betaflight or Ardupilot), press and hold the BOOT button on the flight controller while connecting it to your computer via USB. This is typically required for initial setup or firmware updates.

5.2 Battery Capacity Indicator

The flight controller features a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, eliminating the need for external checkers.

Battery capacity indicator on H743 FC
Image: Diagram showing the 4-level battery capacity indicator on the H743 Flight Controller.

5.3 Black Box Logging

The built-in 16MB large memory FLASH continuously records flight status, including sensor data, control commands, and fault codes. This data can be retrieved for accident analysis even in the event of a crash or power outage.

Built-in 16MB large memory FLASH for blackbox logging
Image: Close-up of the H743 FC highlighting the Winbond 16MB flash memory chip for blackbox logging.

6. User Tips

  • GPS Performance: Users have reported that this FC provides faster GPS fixes and clearer blackbox logs compared to some older F405 controllers.
  • Capacitor for OSD: If you are using an analog OSD and notice noise, consider adding additional capacitors in parallel to the OSD output if you have the necessary soldering skills. The included 1000uF Low ESR capacitor is crucial for overall power stability.
  • General Reliability: The stack has been noted for its good quality and reliability by users.

7. Troubleshooting

  • GPS Not Working / Stuck on UARTs: If your GPS module is not functioning or appears stuck on UARTs, first verify all wiring connections according to the diagram. Ensure the correct UART is selected in your flight control software (Betaflight/Ardupilot) and that the GPS module is properly configured. If using with a DJI Air Unit, ensure no conflicting SBUS signal wires are connected.
  • SBUS/ELRS Receiver Issues with DJI Air Unit: As noted in the installation section, if you are using an SBUS or certain ELRS receivers alongside a DJI Air Unit, you may need to disconnect the SBUS signal wire from the DJI Air Unit harness to prevent interference and ensure proper receiver recognition.
  • Power-up Burnout Prevention: Always connect the provided 35V 1000uF Low ESR capacitor to the battery pads to protect the stack from voltage spikes during power-up.
  • General Malfunction: If experiencing unexpected behavior, check all solder joints for cold joints or bridges. Verify power connections and ensure no components are shorting. Re-flash the firmware as a first step for software-related issues.

8. Maintenance

  • Cleaning: Keep the FC and ESC clean from dust, dirt, and debris. Use a soft brush or compressed air to gently clean the components. Avoid using liquids directly on the electronics.
  • Inspection: Regularly inspect solder joints, wires, and connectors for any signs of damage, corrosion, or loose connections.
  • Storage: Store the stack in a dry, cool environment, away from direct sunlight and extreme temperatures.
  • Firmware Updates: Periodically check for new firmware releases for Betaflight or Ardupilot to benefit from performance improvements, bug fixes, and new features.

9. Warranty and Support

DAKEFPV products are designed for enthusiasts and require careful installation and handling. Damage resulting from improper installation, incorrect wiring, or misuse is not covered under warranty. For technical support, please refer to the official DAKEFPV website or contact your retailer. Ensure you have your product model and purchase details ready when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.