SWEVY SW38A

Contents

SWEVY SW38A Digital Refractometer User Manual

Model: SW38A

For accurate measurement of sugar content in fruits, beverages, and other solutions.

Introduction

The SWEVY SW38A is a precise LCD digital refractometer designed for quick and accurate measurement of Brix (sugar content) in various liquids. Featuring automatic temperature compensation (ATC) and IP67 waterproof protection, it is suitable for a wide range of applications, from fruit cultivation to beverage production.

SWEVY SW38A Digital Refractometer, front view with display showing 25.5°C and 8.8 Brix%
SWEVY SW38A Digital Refractometer, front view.

Parts Identification

Diagram showing parts of the SWEVY SW38A Digital Refractometer: Measuring slot, Prism, LCD, Zero button, Start button, and dimensions.
Key components and dimensions of the refractometer.
  • Measuring Slot: Where the sample liquid is placed.
  • Prism: Optical component for measurement.
  • LCD: Digital display for temperature, Brix%, and refractive index.
  • ZERO Button: Used for zero-setting calibration.
  • START Button (Power Button): Turns the device on/off and initiates measurement.

Setup

Battery Installation

This instrument is powered by two AAA batteries. To install or replace batteries, remove the battery cover on the back of the device and insert the batteries according to the polarity markings. Ensure the cover is securely closed after installation.

Initial Power On

Press the START button to turn on the device. The LCD will display the current temperature and '0.0%' or a previous reading.

Operation

Zero-Setting (Calibration)

Before each use, or if accuracy is critical, perform a zero-setting calibration with clean water or pure water.

  1. Ensure the measuring slot is clean and dry.
  2. Place clear water (distilled or pure water) into the measuring slot. Ensure the water covers the prism completely, about 1mm deep, with a capacity of approximately 0.3ml.
  3. Press the ZERO button. The display should show '0.0%'. If not, press ZERO again to reset to zero.
  4. Wait for the device to stabilize (approximately 20 seconds for temperature compensation).
Image showing a hand dropping water into the refractometer's sample slot for one-click zeroing calibration.
Performing one-click zero-setting with clear water.

Measurement Steps

  1. After zero-setting, clean and dry the measuring slot.
  2. Drop the test sample (fruit juice, beverage, etc.) into the measuring slot. Ensure the sample covers the prism completely, about 1mm deep, with a capacity of approximately 0.3ml.
  3. Press the START button. The measurement results will be displayed within 3 seconds.
  4. For best accuracy, you may extract the solution, clean the slot, and repeat the measurement several times.
Four-step diagram illustrating the measurement process: power on, drop sample, press start, clean slot.
Step-by-step guide for taking measurements.
Demonstration of measuring sugar content in various fruits.

Language Switch

To switch the display language between Chinese and English, press and hold the ZERO button for 2 seconds to enter the settings interface. Use the START button to navigate and ZERO to select the desired language (LANG [EN] or [CH]).

Maintenance and Cleaning

Cleaning the Measuring Slot

After each measurement, or if the instrument has not been used for a long time, the measuring slot should be cleaned thoroughly. The device has an IP67 waterproof rating, allowing it to be fully flushed.

  • Drip clean water onto the prism and gently wipe with a soft paper towel. Repeat this process at least three times to ensure all residue is removed.
  • If the slot contains oily substances or is difficult to clean with water, use ethanol or soapy water, then rinse thoroughly with clean water.
Image showing the SWEVY SW38A refractometer being rinsed under a tap, demonstrating its IP67 waterproof feature.
The refractometer is IP67 waterproof and can be rinsed under running water.

Cautions for Measurement

  • Cold or Hot Measuring Solution: Drop the solution and wait 20 seconds before measuring. The instrument requires time for temperature compensation to ensure accuracy.
  • Solutions with Suspended Substances: Remove suspended solids using a filter spoon or gauze. Ensure the solution is mixed evenly and avoid scratching the optical prism with metal or hard objects, as uneven solutions or suspended solids can lead to inaccurate measurements.

Troubleshooting

Error Message Reason Solution
Excessive light External light is too strong to measure. Move to a less brightly lit area or shield the measuring slot from direct light.
High Temp / Low Temp The temperature in the measuring slot is out of range (10-40°C). Allow the instrument and sample to reach room temperature (10-40°C) before measuring.
Re zero Zero-clearing step was not performed correctly. Follow the zero-clearing steps again carefully.
Less solution Too little solution in measuring slot. Add more sample to ensure the prism is fully covered (approx. 0.3ml).
Less water Too little clean water in measuring slot during zero-setting. Add more clean water for zero-setting.
Out of range Excessive concentration. The sample's Brix value exceeds the instrument's measurement range (0-38%). Dilute the sample if necessary.
Low voltage Low battery voltage. Replace the two AAA batteries.
Fault Possible damage to components. Contact customer support for assistance.

Specifications

Feature Specification
Model Number SW38A
Measurement Range 0-38% Brix
Brix Min. Division / Resolution 0.1%
Measurement Accuracy ±0.2%
Temperature Compensation 10-40°C
Weight 113g
Size (L*W*H) 117mm * 55mm * 29mm
Power Supply 2 x AAA batteries (not included)
Protection Level IP67 (Waterproof)
Certification CE, RoHS
Reset Calibration Function Yes

User Tips

  • Users have found this refractometer to be highly accurate and reliable, with measurements matching analog devices.
  • The device is noted for its ease of use, making it suitable for both beginners and experienced users.
  • The quick response time (results in 3 seconds) enhances convenience during repeated measurements.

Warranty and Support

For detailed information regarding warranty, service, or additional support, please refer to the official user manual PDF. A digital version of the user manual is available for download:

Download User Manual (PDF)

© 2024 SWEVY. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.